I love it when kinda ordinary folks do amazing things that save the kinda average guys like me some money and time. Great video! I hereby subscribe!

Thank you for this video. It showed me this is not a DIY project that I can complete. Will be calling a repair person later today.

I like the way you showed how to remove the transmission when it was stuck. Nice work

Mine is three years old and just started doing this. At first it was squeaking and grinding like a bearing was going out. A few loads later this noise. Since then I have researched the replacement item and can buy it for around $150. Thanks to you I will be doing it with a handyman coworker at my work. Our shop has all the tools.

Great videos very informative, good job

This is by far the best, to-the-point guide on replacing the transmission. Fixed for me, too. The most trouble I had was the unit's four bolt sizes for the transmission - not 3/8". I had to work with 10mm. Thanks for the great show!

thank you so much for the video. saved me a lot. it was impossible to remove the transmission from mine. would not budge. finally grabbed a 30 lb. sledge hammer and banged it out to the very end.

Ours doesn’t make noise while spinning like here…. Buuuuut, damn it makes a super hard knock at the end of spin cycle.. not sure what to do there. Just replaced the dogs in the agitator(noise is not new). I’m guessing it’s some sort of brake? If you have any ideas,I’d appreciate it. I like that fast forward ya got goin’.. cool to watch!

Mine is 3 years old and it just started doing this. Thanks.

Excellent video. 9.9/10 just because I had a lot of trouble getting that plastic U-Clip back in the hub but i finally figured it out by shaving with a steak knife and whittling it down and then putting it all the way clicked in before I put the hub down over the transmission i had to force it down but after getting to the end of the job and spending over an hour just on that U-clip. (Last step) i was very relieved to see it was in, then i just tapped it back far enough to get the screw in that slot and I was able to tack it back into place.

thanks for the video. My problem is when it first 2 spin (when it rinse and spin), it's shaking the machine with a banging loud noise that it move the machine around. However, the last spining ( I assume less heavy load because the water is almost empty) is very quiet. Any advice?

I would love to see the transmission repair. My transmission has rusted splines😢

Thank you sir. Mine is doing this and I cant afford a new one right now.

Excellent video. Thanks!

Great work and nice video, I do not have the skills like you, I am going with a new machine. Thanks.😀

My mvwc565fw1 maytag washer bangs around even with no clothes in it. Replaced springs already same thing thing. What could be the problem. Would a bad transmission cause this?

My whirpool not only made loud noise, it shifted as well and cloth were not draining if I used large and super load.

I encountered this problem after I replaced the actuator on my washer. That's crazy if my sealed bearings went the very next wash cycle after I replaced the actuator/tachometer

Can I do the same with my g e washer

The bearings are probably common. I’d like to see you try to replace them after removing trans and shaft. Might need a press.

My whirlpool washer only screams during the braking cycle of spin, when it is trying to slow the tub from spinning. Any ideas. Is that a transmission issue as well?

Mine squeals when it spins, even when I turn it by hand. Any suggestions on why that might be? I've already changed the seals & bearings.

What if it makes a grinding/screeching noise at the end of the spin cycle?

love the name of your channel

I have an washer that just started doing this. It’s an older top-loading Frigidaire. It doesn’t have the sealed transmission box like this one. I’m looking for a video on how to fix it. I think it will be more complex than this repair, unfortunately.

Very helpful video I have subscribed

Thanks so much very helpful

So if I don’t have the extra $175 available till next payday(not for two weeks) and I can deal with the loud noise, is it ok to use the washer??? Basically, is it just annoying but since I can deal with the freight train in my washroom, it’s ok to wash clothes??? Really appreciate anyone that helps with their knowledge!

Thanks, my toploading Maytag screeches during spin cycle. Could it be the same problem? Also there is no tag with serial number on machine.

I have the same washer and it makes the same noise when it spins

Mine sounds like its slipping and never engages in a full fast spin. Cranks up to spin, makes an awful noise and just lets it free spin until it winds down. Could this be the problem?

Great video. Thanks for sharing. New subscriber here

great video thanks

What causes the bearings to go bad? I have a whirlpool doing this and it’s only two years old.

Never buying Maytag again, this thing hasn’t lasted 3 years and it’s already falling apart.

I have a whirlpool washer that makes a horrible grinding noise at the end of the spin cycle not during any idea ?

Very helpful

What is the trick to get the wash plate out of a rusted spindle?

My Crosley sounds like a freight train in the spin cycle

How can i test the spin or rinse spins without putting water on it? So i can fix and work on it much better

Might as well replace the washer lol

Fantastic video this is exactly what's wrong with my washing machine but how do I reach him? I want to talk to him and see if he would be able to come and repair mine but I have not been able to find any way to contact him does anybody know? 🤷🏾‍♂️🤷🏾‍♂️🤷🏾‍♂️🤷🏾‍♂️🤷🏾‍♂️Does he have an email address or a phone number there's nothing listed on these videos!!!🤬😬😡🤦🏽🤦🏽☹️☹️

solid

My washer is really loud in the spin cycle, I do have some videos of my washing machine spinning that you can watch:

That’s a lot of work. I will never buy a Whirlpool again

Diy milestone

What’s the part number

This is too much! My machine is a Whirlpool, not even a year old, and making a sound just like in the video! I’m sick of it and will never buy another Whirlpool ever again!