Just received my Fly Sky FSi6x and your tutorial video was OUTSTANDING, thanks dude! I love how the manufacturer entirely blows-off even offering a manual, too funny

Thanks again!I'm 54 years old noob and about to fly my first fpv drone!Great video for beginners like me!

This is the first 2.4ghz radio I've brought after a 20 year absence from the hobby,and its brilliant for the price. Its range is excellent and relatively simple to operate and reliable. I used to fly with Sanwa Vanguard 35mhz back in the day.

Some moments were helpful, like the dual rate. But it would not hurt to explain what some terms mean. For example, what does EXP in the dual rates mean? Or which output should be selected and when? For example, there are two connectors on my FS-i6X receiver for connecting to the FC marked PPM and i-Bus. Which combinations should be used for using each of them? Or what is the i-BUS Setup menu for?

just set up my yachts with the dual rate for the rudder. Excellent instructions thank you

awsome that press and hold cancel was everything i needed THANK YOU!!!!!! awesome instructions some of the functions were also helpful!!

You are a very good instructor. Thank You. John Meksa 76 Year old beginner.

Just received mine today! My plane will arrive by next week hope all goes well thanks for this! :D

Thanks for this demo.. just trying to learn how to set up switches to do different functions on the aircraft, for example trying to set up switch C to do the three functions of my ZOHD Nano Talon so that 1 might be stability mode, 2 would be stability off and 3 using the the bigaole stability module would be the return to home if the aircraft got out of range on me. Still trying to figure it out. Will read your channels and switches again to see if i can do it. Thanks again. Happy Flying

This had some very valuable information, thank you!! I'm a 56 year old *flying* N00b... but have been in RC Ground for over 35 years... If anyone can help, it would be appreciated. 👌 I've got the FS-T6... all I can afford. It's just for FliteTest Foamies anyway. Are the functions much different from the i6 and i6X?? This Video got me started, and I really appreciate it!! 😎👍👍 One thing not covered was Channel Mixing... Specifically, until I can stay in the Air for longer than a Minute - I'd like to mix about 3-6 Degrees of Up Elevator with my Aileron input. (Automatic Bank & Yank??) Is that even possible? I flew the real ones in the Air Force back in the 90's... I've been told that could actually hinder my learning. But remember, I'm also very experienced in RC Ground and at least have a firm understanding of Control when the Vehicle is coming towards me. Other than that, I've still got a LOT to learn!! 😋😳 I hope someone can help me with Mixing.... Carmine ✈🚂🚙

I have ordered this transmitter for a beginner rc plane. Thanks for your helpful video.

Awesome video! Thank you. After seeing your video the first time I decided to give Flysky a try. Been flying Spektrum. The Fs-i6 and x models are fantastic for the price. May try the FS-i8. Incredible technology for around $100.00.

Well worth looking at l am learning all the time at 64 years old Thank you

Dude you cracked me up when you said if you reverse channel three crazy shits going to happen, I got 30 stitches and 9 staples on my arm when I did just that with a 200srx. Ouch!

Thanks from India 🇮🇳 Sad to see you have only 9k subscribers

Thanks for this! Your tip to turn on the switches helped me get the trainer/student buddy box working.

Would you please explain how to set up the fsi6x to use IBus?

Ahh that explains it..so to dampen the sensitively around the centre of the stick you use positive expo in this case the "up" botton will make the movement less sensitive around the centre and the opposite with down button - minus ..been flying 20 yes but this as always confused me because without flying it you can't tell what is minus and what is positive. .Thanks for that.

Great video. It would be nice if you explained the “expo” though. I am new at this and have no clue what expo is…

This was very helpful. My first digital radio and just getting back into it after a 20 yr. layoff. I was not able to access switch A for my dual rates, so I put it on B. I still don't know why A was not available. This is a four channel nitro trainer. How do you set up an idle and kill position on the throttle?

I need a lay down in a quiet room for a while. Thanks for a very valuable video, but setting up systems with just those buttons and needing to learn the difference between a quick and long press was a pain lol.

Buliding a tank from scratch and learning this is the hardest part, lol

Thank you ,i was having problems setting switch to reverse as i am new to rc. i watched other videos none helped, your video you say to save you have to hold cancel button i was just pressing and releasing it,

best flysky videos online. Thank you.

I got it i got it !!! lololol from your instructions I figured how to assign channel 6 to the switch plug, so I put it in the receiver 6 position, and yes, it worked but was backwards 3-2-1 .. so I wondered if there was a way to reverse a switch and voila !! there is, and I reversed it and now the third position is return home. Merry Christmas and Happy Flying

Fs i6x is mixing channel 3 throttle with channel 4. 30a esc wont stay programmed running an Amazon 2200kv. Wont go full throttle unless I full rudder and full thottle at same time. I've google but can't find this problem. Thanks! You make some great videos!

I don’t know what I did but I got my mob7, binded it, and everything seemed fine. It was SWA to arm/disarm which is what I wanted, SWC switched from Acro mode to Horizon mode or auto level mode. I switched some stuff around like turned the VRA and B knobs off, which I later turned back on. And I switched the Aux settings a bit but it wouldn’t fly... what I ended up doing was setting everything back to how it was, then I put the aux channel 1 5 to SWA and then the other one (6) to SWC I believe and what I had to do was turn on Fly mode and set it to SWA arm and disarm and now it works again but I don’t know why it wouldn’t work normal when I set everything back...

Cara muito bom preciso faser essas modificações no meu radio agora é passar seu vedeo mais vezes para ver porque não falo inglês

This is a great video but for the term beginner. As a beginner/newbee, I want to know not only the what, but the why. I.e. setting up the switches. Also, you speak faster than I can hit the pause button.

failsafe is one of the best functions for newbies incase somebody is helping you trim.

I have no clue what any of these transmitting signals do but IDGAF, I'll probably never out grow this transmitter. this thing is sooooooo bad ass though! it works perfect! i was even able to solder on a new switch that i broke on it.

awesome!

Just the right place, you hit the nail on the head for me.

Perfect instructions. Just what I needed. Thanks man :)

For RC planes , what out put should I use ?

very informative.. more than the Chinese manual :)

Great content! Thanks

Super great video. I’ve just built my 1st RC plane and I have a question: how should I setup the Ailerons? I have a servo for each wing for right and left and cannot figure out how to manage that. Thx a lot!

would it be possible to turn my servo the full 180 degrees using this controller?

thank you so much for your sharing. terima kasih

nice smile 😆😁😁 0:37

Awesome thanks for the video

I'm setting mine up now in my skytrainer , should it be in PPM, or PWM ?

How to make the alieron and elevator mix ? For example when I turn left and right with the alieron I want the elavtor to move up aswell . instead when I turn to one side the elevator goes down and when I turn to the other side it goes up . how to make the elevator stay up when I turn both sides?

Why in my assignment swich up and down button not working for cheng positions in normal and sport??????

Thanks!

This is useful for me, thank you very much, may all the good for you 🙏😁👍❤️

What does dual rates and expo means? How does it affect the airplane?

Hi and thanks for the great video. Is there a specific way of setting up the Reflex V2 gyro. It has no gyro, intermediate, and beginner ona 3 way switch. However on a 2 way switch it has intermediate and beginner. I cant seem to figure out how to set it up. I use my 3 way switch for flaps currently. Thanks very much Bob

How many extra switch stickers do you get with the remote control

Gey great video ! Only question is, how I setup a Gyro ? I have everything wired and working but I can’t get my gyro onto one of the switches to turn on and off , thanks !

Hi, Adam - I'm trying to set twin motors up, but the display is showing 66% on one side, and 100%on the other - how do I reset to 100 % for both, please?

YOU are the man

I am using the Flysky for a giant scale airplane with a gas motor. I had to reverse channel 3 to get throttle to move in right direction. Can I still use failsafe? Thanx

Do you have video for the setup of external module like crossfire

New to FPV I have a fs-16x I am using Liftoff to learn, I would like to setup the transmitter for my X220 drone what setting should I change.

Hi, I love my FS-i6X I have a problem with flying with Nitro power... MY problem is the main Throttle trim on the front of the transmitter For some reason will not move a SERVO ( try it yourself) I think it has something to do with speed controllers verses a SERVO hooked into channel 3 .... All the other trims will move servos just fine but NOT channel 3 there is no info in the user guide... and I have a different FLYSKY transmitter too (FS-ST8) which the same problem exists... Any ideas for me... Robbie

Hi, my best compliments about video...so I have a question for you I have necessity to invert the channels in "stick mode". Menu offer "mode 4" but i need to invert the position (CH1 with CH3) and (CH4 with CH2) what I can do it?? can I invert the cable inside or what? I hope to explained well. Thanks for your answer! ;-)

thank you!!!!im 3 day looking for the save button...... its really wierd tha you have to hold cancel.. i was holding the ok button like craizy.

Does the Does the isx support h1-v2 for fw200 helicopter GPS and acrobatics

Hello. What about air brakes or spoilerons? How it have to do? Thanks

How do you know what receiver set up. Mine came with a 10 channel receiver so is this ppm and s bus ????

If it looses range, and if the throttle is cutoff wont, it crash the drone? Is there a way to let the drone returne to base as failsafe option?

I noticed I have to turn on the mixes whenever I shut off the remote. Am I doing something wrong that they don’t stay on?

I need help! I have a Flysky I6X transmitter to control my tracked inspection bot. But when I first switch the transmitter on, it beeps and gives me this message: "!!WARNING!! Place all switches in their up position and lower the throttle" Sometimes I just bump my left toggle switch, channel 3, and it stops the warning and gives me full control. But all too often, it doesn't matter how many switches and toggles I move around, it just keeps beeping and will not give me control. What is it doing and how do I get it to stop? I have a simple tank chassis with a light and camera gimble on it. It's not like I need a safety switch to start with. Can you help me?

Hi noobie here just bought a i6x do you have a tutorial to setup for hexacopter f550 with apm2.8

I have flysky fli14+ but not binding..when i click bind key on remote then power it says "key stuck".

My RX receiver led blinking not pairing with TX what is the solution

Is there a way to make channel 3 and 4 controlled via the switches normally used for aux channels 5-10? I need to make channel 3 controlled via SWA or VRA

thenks.amazing

How can i make channel 5 swA turn on and off a cooling motor with 2 wire red and black.

geht es das man zb den linke steuerknüppel doppeld belegt einmal zum beispiel zum fahren kettenantieb und dann wenn man ein schalter umlegt zum arbeiten nutzt brauch man beim bagger zum beispiel linler knüppel zu drehen un arm heben senken und mit dem rechten steuerknüppel schaufel un vorder arm nutzt

Love the end of the intro with the smile, classic infomercial “your about to get ripped off just 99 easy payments of $99.99....” (que smile)

How would you bind it to an Eachine P51d mini mustang? I have the module that you plug in but cant work out the rest lol. Great video.

Is 4 channel flysky i4x compatible with fpv

Hello Adam, Lou here. I just saw your video. Having a heck of a time setting up this transmitter with a PicaSim flight simulator... are you familiar with it? I do have to say that I did pick up more on your video. I went through the motion mentioned on sim set up but cant get the plane joysticks to function. Any advice to remedy my issue?

Hi Adam! Need some help! Got a quad with fly sky FS A8S receiver and the radio FS-i6x. There is an issue when I hit full throttle on my quad.. it says rx loss for abt 1sec and after it gets normal.. but it's not very safe to fly like that.. maybe u got any idea what could it be? Receiver issue, radio or even some kinda vibrations on high throttle? 🤷‍♂️

Im building a rc mower. If I heard you right you can set two channels to fail safe? I have a servo to close throttle and kill the engine. And a remote relay to cut power to the motor controller.

could ayone tell me what the maximum control range of this radio

ppm output is off if i turn on the receiver bind everything work?? or just lets it off?

thanks for the tutorial, I use my fs-i6x for tanks but I wanted to ask if you have a tutorial on how to set up the i-bus on this tx?

you could also cover the difference between positive and negative expo

is this compatible with receivers that have gyro?

Have you done any Flysky firmware updates to your i6X? How did you handle the virus infecting Flysky's firmware image? I haven't been willing to sacrifice any of my PC's to try and work it out.

Hello and thank you s overy much for your awesome video as it helped me setup a few features in my i6X. One question though if you don't mind? Is there a way in which the gimbals can be calibrated. Because if I setup failsafe on my throttle it only goes to 93% and not 100% like in your video. Thanks

Can you help please in regards to setting the no. 3 output to be able to be used for throtal forward and throtal reverse ie for a boat????

What are the 2 iner switches for the one to left and the 3 position one

Thank you for your tutorial. Problem, hoping you can help with please. When I have channel 1-4 as factory sent, channel 5-10 off and unassigned and all switches in down position, remote starts pleasantly, except I cannot use channels 5-10. Once I assign all channels up to channel 10 their each switch or control, and save with cancel button, then when turning remote on it yells that all switches must be in down position. THEY ARE DOWN! If I go back in and turn off channels 5-10, starts perfectly again. I would like to use additional channels and cannot figure out what I am doing wrong. Can you please help?

Any body know what I set the receiver out put to with there 10ch receiver. Pwm or ppm, I bus or s bus ????

Thank you, thank you, thank you!!!

What is the farthest range of this transmitter?

So many thanks man. That helped! ;-)

Yea uam new and need all the help o can get I have the echine wizard 220x with the flysky i6 s ready to fly

Hi I've had a lot of signal losses recently and I was wondering whether I could set the failsafe to elevator up or if that was a good idea with throttle at 25% Thanks for your help

Great video. One question: I have a FMS Reflex v2 gyro and I want to use this with my Flysky i6x and receiver fs ia10b?

Great video thank you 💯

Great video! I was wondering if anyone knew of a way to reverse a channel by flipping a switch. I have a bot that can drive upside-down if it is flipped over, and was wondering if there was any way to map one of the switches to reverse the directions of the motors. Thanks in advance!

Thank you very much. One thing is puzzling me - the 'display' is only showing six channels, instead of ten? Ten is on the Aux etc. Den, Wales

I know this is a 5 yr old video but I'll ask anyway. I'm getting into this hobby and since it is a good budget Tx for beginners, does it have gyro settings? In the manual it says it does, but under the "Helicopter Settings" section. Dunno if that works the same for planes... or I would have to get a different receiver than the one that comes in the box?

PLEASE HELP 😫 I’ve watched dozens of your videos..watched HOURS of videos for almost a week.. I haven’t found a single one, that shows if you can set the endpoints for channels 7-10.. Everyone shows the aux page, and how you can set 5-10 to any switch/variable knob.. but I haven’t found a single video that shows if you can adjust the endpoints across all channels. I just can’t make myself buy another radio, until I know if I can do this. Please help! (P.s. your channel is incredibly informative, and entertaining, btw! 👏🏼)