Thanks nice clean work and good video info. Cant get more easy to understand than that keep going we're new to the channel but im glad we found it
@hueyfabllc4987 Жыл бұрын
Thanks! I appreciate the feedback!
@boogiechassis7726 Жыл бұрын
Man, thank you for this video! Always wondered how low you can get a CV swap! Really appreciate the highlight on the Outcast Autoworks control arm mount, too!
@hueyfabllc4987 Жыл бұрын
Thanks man! Kyle makes great parts that hold up and look great, too.
@boogiechassis7726 Жыл бұрын
@@hueyfabllc4987 I'm in Dallastown, PA. Really glad to see local(ish) vendors making such nice solutions. Looking forward to more content, big guy!
@leviunruh439 Жыл бұрын
Great job man. Thanks for showing us!
@hueyfabllc4987 Жыл бұрын
Thanks for the response and for following along!
@rodriguezadventures865 Жыл бұрын
Looking good dude!!! Solid dude and work all the way around!
@hueyfabllc4987 Жыл бұрын
Thanks bro!!
@matthewremines4954 Жыл бұрын
Awesome work. Looking good.
@hueyfabllc4987 Жыл бұрын
I appreciate it!
@Backwoods_8709 ай бұрын
👍🏾👍🏾👍🏾👍🏾👍🏾
@dannychiguina3962 Жыл бұрын
Awesome 👍 job guys
@hueyfabllc4987 Жыл бұрын
Thank you 😁
@hugecat27 Жыл бұрын
Nice work brotha.
@hueyfabllc4987 Жыл бұрын
Thanks man!
@edwardlocke874 Жыл бұрын
Thanks !
@hueyfabllc498711 ай бұрын
You bet!
@infamous_d4011 Жыл бұрын
Is that the ride height on the front with stock crown vic springs? Amazing work, and content! Love your channel brother.
@hueyfabllc4987 Жыл бұрын
It would be close, maybe 1" higher, but this setup has aftermarket coilovers adjusted to sit low. No motor or trans in here yet, so it will settle another inch, inch and a half once that weight is in there.
@matthewmanning9578 Жыл бұрын
Heck yeah brother looks good. You made it look to easy.
@hueyfabllc4987 Жыл бұрын
Thanks man! Realistically, it could all be done in 20hrs or so. Not bad at all.
@matthewmanning9578 Жыл бұрын
@@hueyfabllc4987 id be afraid id mess it up. I've got my 70 going back together now so hate to take it back apart. Hope to go to grand nationals and take over again this coming year.
@hueyfabllc4987 Жыл бұрын
@@matthewmanning9578 looking forward to it myself....and seeing all the great f100 folks.
@randydarcey2947 Жыл бұрын
5 stars
@hueyfabllc4987 Жыл бұрын
Thanks Randy!
@Moneypit330 Жыл бұрын
I am interested to see your 4v in Frank with the frame Z. It looks like the vic crossmember naturally sits the engine lower. I swapped a 5.4 2v into my 67 using the the Ibeam suspension. It barely fit under the hood.
@hueyfabllc4987 Жыл бұрын
Yep. The vic cradle sets the engine several inches lower than stock. With the frame zee, it still puts the 5.4 intake below the cowl pinch weld under the hood.
@lariat8653 Жыл бұрын
It’s been along time since your last video, I was wondering if you had just quit with KZfaq videos. Film more of the whole process of the work and post it up on here. I’d love to watch it when I can fit it in.
@hueyfabllc4987 Жыл бұрын
I sure will. Was just thinking today I need to capture more. Got some co stuff coming, so I think I'll do build series to keep content coming. Thanks for the response and for following!
@w.jaybradford1309 ай бұрын
Is it possible to do this workout removing the cab from the frame, is there enough room to do that with can bolted down?
@hueyfabllc49878 ай бұрын
Unfortunately no, the cab mounts need to be removed and re installed to make a cut far enough back for the vic trailing arm. Now, if using a different front suspension, it is possible.
@johnjordan286911 ай бұрын
Whats the measurements of the line's you marked on the frame. And whats the measurements on the front. Thanks
@hueyfabllc498711 ай бұрын
In this case it was 2.5", but its based on how much you want to lower the truck around the suspension. Anything more than 3" is going to require more sheet metal work to the cab for Driveline clearance.
@mikeilikeit968511 ай бұрын
I want buy those suspension ,where can I get it?
@toolmantommy9561 Жыл бұрын
How low is the pinch weld on bottom of cab from the ground
@hueyfabllc4987 Жыл бұрын
At the cab mount or the rocker?
@procharged6854 Жыл бұрын
Im trying to determine the amount Im zeeing my frame, Im wanting it to sit low (not quite as low as frank sits but close), I purchased all of outcasts rear suspension, but then also got the viking front coilovers that are already lowered from stock crown vic stuff. Have you ever zee'd a truck using coil overs up front? If so how much did you go?
@hueyfabllc4987 Жыл бұрын
Every truck I've zee'd had coilovers. This one has ridetech, did another one with vikings from f100performance. My green truck (video on this channel) is zee'd with ridetechs as well, but I'd consider it as low as you can get. Meaning, you could adjust the coilovers up 1-2" and achieve your desired height. The Fred truck (video on this channel) is stock frame rails, cv front, viking coilovers adjusted as low as you should go on stock rails. Hope that helps!
@procharged6854 Жыл бұрын
That helps a lot thanks! I was thinking of just doing 1" zee, Ill look some more at the other trucks youre referencing and judge how much lower Id want it from there.
@PeterHatch-mx7zc Жыл бұрын
Do you have a template for crossmember and yes would you sell me one ! Thks