Don’t give him any encouragement 😂

I graft hard 😉

I won’t Mate don’t worry lol 😉

They go on anything mate just need a roof rack and you can always remove it if you’re not using it

@@richardstokes2209 once this merc gone mate I’d have nothing fit it to 😂😂 I could fit my Renault 5 inside one I bet

How dis you get on with bonnet latch mate as it dosent boot on and cable to short

Thanks mate we are really happy with it and you have a good Xmas as well 💪

Where could I get the conversion kit ?

There just plug and play the rear lights

@@richardstokes2209 is the wiring loom behind the fuel cap / chassis

@@garypryor3799 it’s at the back underneath behind the rear bumper on the underneath the tub there is x2 plugs on the loom for the rear lights if you remove rear lights follow the light lome you will find the plugs

Yes

Thanks mate and no wasn’t going to as all the plugs for all the different switch’s and that will be different and be a complete nightmare had anuff of a challenge with the headlights lol

Most are Ford but arches and rear lights and grill are aftermarket

No problem mate I was in the same position as you got the truck then kept seeing the newer front then one come up in the same couloir and had to do it 💪

Unfortunately not, we had to just fit the standard bulbs back in (which are awful), as the LEDs kept messing up the BCM system. We may do a follow up video if we can get them to work though!

Thanks and yes the lights are really rubbish I keep thinking I haven’t got them on 😂

Yes there not the best as they can pull apart but I put a load of electricl tape round it but we will see

@@richardstokes2209 I did same mate it’s literally the connectors you push in i had issues not touching

Basically you need to order x2 bumper headlight brackets what bolt onto front frame you can get away with not running them Then the bonnet latch you use the t6 latch as the t7 is completely different and doesn’t bolt on and pull cable for bonnet release and open bonnet sensor are all different so you have to modify the t6 latch. how I did it was re drilled the t6 latch so it sits 10/15mm higher then you use the t7 bonnet part that goes into the latch but it’s a thicker gage steel so it is to fat for the latch so I just ground down to the same gage as the t6 then the bonnet catch will work you can also us some washers as fine tuning on the bonnet side to space it down If you’re t7 bonnet comes with the jets your fine it will plum up with pipe but if not the t6 jets are completely different and won’t work on t7 bonnet The t7 also uses bonnet struts and not a bonnet stay but I still use the t6 bonnet stay I will fit the struts at a later date

@@richardstokes2209 Legend, thank you!

All depends on if you buy new £2000 to £3000 I’d budge parts and paint

Unfortunately no but it’s not that hard to work out it’s just lives and grounds

Mine come with the front end I bought it has x2 self tapper screws in the bottom that have been fitted so you might have to do the same and the Ford logo is fixed already on mine but have no idea where it was from hope that helps 👍

@@richardstokes2209 appreciate that mate thanks, yea it came about a dozen or so screws so I did think it might be something like that. I’ve managed to find some FORD letters online for £30 they have screw holes in the back but I’ll need to find some sort of retaining clips from somewhere. I personally think this style of grill is far better than the wildtrak or raptor one. The only thing I’m not too keen on is how far it sticks out. From the front it looks great but from the side I my kinda gives it a big nose lol I’ve seen a small few colour match the trim of the grill to the truck which looks pretty smart

Use the t6 catch and you have to shave the t7 latch on bonnet as it’s to wide to fit into catch but once you reduce the width it fits 👍

Or down his shorts messing with his tackle

He don’t do a lot he’s probs got cold hands 😂😂😂😂

Lost some weight haven’t I 🤣

Get all the parts from Ford or second hand and there is company’s that do the arch kits and we only do our own cars 👍

Thanks a lot Very much appreciated

Hi, How mutch does it cost to do all of that? Thinking of doing mine

The front end I got had led bulbs fitted and it made my bcm turn the lights off so I had to fit the standard bulbs and use a code reader to go into bcm and rest and like you say the lights are shocking what I think I am planning to do is fit the mustang headlights that are led but have something in them to trick the bcm as I have led rear lights that do the same thing and have not given me any trouble

@@richardstokes2209 cheers for the reply richard so with the headlight bulbs can i still change the side light bulbs fog light bulbs and projector bulbs all to led just not the other bulbs that are none projector

@@theanton9633 yes if it’s fused at the fuse board you should be fine if it’s through the bcm or cambus system it can play up but the other way to get round this is if the led has a resistor in and tricks the bcm and cambus system as I have fitted led rear lights with no problem as they have resister in to trick the car this is also the same when I get some aftermarket front lights like the mustang headlights they all work as they have the resister in hopefully that all makes sense 🙈😂

Brill job guys So how much to change my 2015 wildtrak?? And can you do the job for me?

Just down the road, not too far from yourself!

It come with all the parts I bought second hand so don’t know we’re it was from originally sorry

@@richardstokes2209 no problem at all 👌 it's look really nice on your car 👌

Really easy and makes a real difference to how it looks

I am good mate think Dave is good jacks a bit hungover but we are all good hope your well Martin

@@richardstokes2209 all good here good to see the team back together

I’m back mate I don’t wanna be cocky but take more them Covid/hospital to get rid of me 😘❤️ I’m here to stay 💪🏽

The front end is all Ford parts so you can get them second hand or new the arch kit a lot of companies do them for the ranger all you need to convert to t7 is bonnet x2 wings bumper x2 headlights front grill x2 headlight supports you have to modify bonnet catch and the t7 bonnet uses gas struts instead of bonnet stay but you can use either also you have to wire in some of the t6 lights to t7 headlights just the dipped and main beam and sidelights it is not a hard conversion if you know how to us a spanner you will be fine

The front end is all Ford parts then there il lots of companies that sell the grills and arches

We have a bmw e46 track car that we are going to go all out on so stay tuned for that as we are just collecting parts at the minute for it

There is lots of options in the uk for the ranger

Unfortunately it’s about us and the cars we work on that’s the point of our channel 👍