Thats what I was looking for! The EGR of my EU5 Transit form 2013 looks the same! So that clip was very helpful!
@kennedysgarage3281 Жыл бұрын
Thank you kind sir 😉😉😉👍
@dannyboi0235 Жыл бұрын
I managed to change my egr valve from this video! Super helpful, thanks a lot 👍
@kennedysgarage3281 Жыл бұрын
Well done Danny 👏👏 no bother to you & I’m glad my video helped 🙏🙏👍
@Gravstein2 жыл бұрын
The radiator fan can be removed for more space to work in. It pulls right up, lover tabs holds it in. bend them out a bit and lift the hole fan shroud. Unplug the 2 wire pugs and lay the wire harness to the side.
@kennedysgarage32812 жыл бұрын
Handy to know 😉🙏
@wackey34552 жыл бұрын
What the heck are them comments underneath some weirdo...... Great video Peter just goes to show if your not a mechanic do you homework before you mess with parts expecially with egr valve
@kennedysgarage32812 жыл бұрын
I’m just after reporting those comments 🤷🏼♂️ These egr’s seem to be a very regular thing for sticking/seizing. The motor is very easy to remove ( make sure to bring up the bottom part too ) well worth a look for any running issue. Thanks Paddy 🙏👍
@lovepreetsinghhanjra19972 жыл бұрын
Nic video sir 👍👍
@kennedysgarage32812 жыл бұрын
Well done & thank you for watching all my videos so quick 🙏🙏🙏
@billyryandoherty8 ай бұрын
hey guys great vid, im gonna give this a bash tomorrow as im sure ive done exactly what you described and snapped the little magnet off the inner erg motor head connection whilst replacing the glow plugs, if i did that would in normally result in the van not starting and just keep turning over?
@kennedysgarage32818 ай бұрын
Hi Billy, I have found on several occasions that if an EGR valve gets stuck open it will stop the engine from starting. So yes it could do that 🤞🤞
@raymondburke1261 Жыл бұрын
If I replace it at home, do I need to tell the computer that a new one is fitted or will it work it out on its own? Good video by the way👌
@kennedysgarage3281 Жыл бұрын
If you wanted to be comprehensive, clearing faults & EGR relearn would be great but just fitting it is enough and the van will relearn over a drive cycle. So yes go for it Ray 💪💪
@SkittlefabzSRT4 Жыл бұрын
Is this the gasoline engine? And is it the same as the diesel engine?
@kennedysgarage3281 Жыл бұрын
My one is the 2.0 diesel engine. I cannot remember the engine code but it is a very popular engine in the Transit Custom
@kieranmorris3640 Жыл бұрын
Can I re-use the gaskets? The egr valve I have just ordered does not come with new gaskets
@kennedysgarage3281 Жыл бұрын
Yes, I usually would. They are steel and should be in good order 😉👍👍
@Abigail_Onpaws Жыл бұрын
Thanks, replaced following your video. I do now have since though engine management light and traction control light. Will that just clear through a relearn?
@kennedysgarage3281 Жыл бұрын
I’m assuming that you had engine management & traction control light illuminated before you replaced the egr valve. General traction control or abs fault appear due to engine related faults. They might go out over a drive cycle or 2 (from cold to hot) but if not you might need to erase faults in all modules with a scantool
@SeanConroy4 ай бұрын
Great info. I was told to do the EGR ahead of a suspected head gasket replacement as the engine management and traction control lights were showing which won't show if head gasket is issue. Don't have the diagnostic tools to relearn the system, will it still work on replacement without the reset?
@salvor18 ай бұрын
what year and engine?
@kennedysgarage32818 ай бұрын
2014 and 2.0 diesel
@the_retired_mechanic2 жыл бұрын
Oooo no wonder I have a bad back. Years of leaning over the front of cars removing stuff like that.
@kennedysgarage32812 жыл бұрын
I think that’s the reason we all suffer from them 🤷🏼♂️😉
@lszek2186 Жыл бұрын
I do not like that you are dragging the old egr valve on the plastic body part of the vehicle scratching it all over like the hole vehicle would be already a scrap.If it is your own car it would be fine but other than that it's a no no no.
@kennedysgarage3281 Жыл бұрын
No plastic parts were scratched during the recording of this video, apologies if you thought they were 😔