Front sway bar bushings replacement on a Toyota Camry Avalon

Рет қаралды 3,746

4 ай бұрын

Пікірлер: 26

@Aziz-wl1xf Ай бұрын

Thank you for this video! I was very frustrated with this design but the idea to only remove one bolt didn’t occur to me. It was still tricky to get the bushing out and in but within a few mins of trying I got it.

@Sagemeister007 Ай бұрын

Thank you!

@elchanojose4633 Ай бұрын

Hello! Thank you for taking your time to watch our video and hope this was helpful. Take well care!

@jorgevega238 Ай бұрын

Thank you

@elchanojose4633 Ай бұрын

Hello! Thank you for taking your time to watch our video and hope this video was helpful. Take well care!

@Ervinsantiz 6 күн бұрын

Mi amigo necesito se tu ayuda, tengo un tercel 94 y tengo un problema al momento de poner en modo parking se bloquea y no puede salir de ese modo y tengo que usar siempre el plan B. Me puede ayudar a resolver el problema 😊

@irisbaez1972 2 ай бұрын

NOOOOO. Those bushing must be installed dry. Do not put any grease or you will have to do the job twice like me.

@Aziz-wl1xf Ай бұрын

You can use vegetable oil since it’s gonna dry up fast and won’t damage the rubber. That’s what Hynes manual recommends

@irisbaez1972 Ай бұрын

@@Aziz-wl1xf Wrong. Do not believe in Hynes Manual. I believe in what Happened to me. I asked a lot about this and all sop, dealers, mechanics do not recommend this with any grease. Must be dry like a bone. I put grease in a new one and starter to squeak noise.

@Sagemeister007 Ай бұрын

WD-40 is not a grease. It's a lubricant. Vegetable oil/olive oil are fine too.

@tomm2271 3 ай бұрын

Hello from Ohio! I have a 2017 SE and it makes a terrible noise when bouncing in the front. My thought is the bushings like you suggested. It only has 33K but I've read that the bushings are known to be a problem. Should I change them.... What do you think? Great video sir!

@elchanojose4633 3 ай бұрын

Hello! Thank you for taking your time to watch our video and for reaching out to us with your really good question. If your car suspension is making a terrible noise when bouncing at the front, I would lift the car and do a visual inspection to see if the are any loose bolts or obvious problem. The bushings for the sway bar are not that expensive they are about $20 dollars at Autozone. The expensive part of this would be labor. Some times we think is this but it ends up being other parts. For peace of mind, have the sway bar bushings replaced being the cheapest parts and at that moment the person doing the job can see if other parts are needed to be replaced. Hope our point of view is helpful. Take well care!

@tomm2271 3 ай бұрын

ok, thanks again! Very good video sir! @@elchanojose4633

@lroc4st 3 ай бұрын

Recently I replaced my struts , control arms, sway bar links & bushing , the issue I’m having is my sway bar link is rubbing the bottom struts when turning L or R and clunky noise, how can I fix this ?

@elchanojose4633 3 ай бұрын

Hello! Did you put them the way the old ones came out. Sometimes what end up happening is that we put them in the wrong way. To better help you on this issue, we are going to share the link to how we did the replacement on the front link kits to our Camry and how this can be helpful. Take well care! kzfaq.info/get/bejne/bcWlY66S38fUZ2Q.htmlsi=ypO8glFpj3fer3Nq

@willpage79 2 ай бұрын

Do you have to take the sway bar link because that aint move anything or loose anything?

@elchanojose4633 2 ай бұрын

Hello! We did not have to disconnect the link but some times what worked for us might not work for others and they have to go one step farther on disconnecting the link kit. We did not disconnected the link. Take well care!

@Itzvinnyboii 2 ай бұрын

Nice video bro. I’m doing my 2004 Lexus es 330 bushings. I have basically done the whole front suspension and this has been the hardest part 😂😂. The bolts that’s under the subframe is rusted as hell and the 12mm won’t grab it I’m looking for a small vice grips and gonna try to use some heat again to get this mf out!!!

@elchanojose4633 2 ай бұрын

Hello! Some times replacements can go so smoothly until the one bolt that is the most hidden and hardest to grab and will not cooperate to come out. Hope this issue is resolved on your side so you can finish replacing what’s left to do. Take well care!

@Itzvinnyboii 2 ай бұрын

@@elchanojose4633 thanks bro. I ended up bending the bracket and sliding in the new bushing and bending it back down and re installing it 😂 hey it worked and on a 20 year old Lexus it’s all good

@davidkomas7563 2 ай бұрын

Is it the same for a 2013 Avalon XLE hybrid?

@elchanojose4633 2 ай бұрын

Hello! We did some reference for the part and looks like is the same for the 2013 Avalon XLE hybrid. When you buy parts, always save the receipt for exchange or return. Take well care!

@luisramos4284 3 ай бұрын

How much you would charge for this job?

@elchanojose4633 3 ай бұрын

Hello! I have seen shops or mechanics charging up to $200 for a job like this. If I was to replace or do this job, I would start by calculating how many hours it is going to take me to do it. This job can be done in 2 to 3 hours depending if you have the tools for it. I would charge around $150 and up. This job can be challenging do to the limited space but in same cases you can charge more. Take well care!

@irisbaez1972 2 ай бұрын

@@elchanojose4633 If you have the right tool, you could this job in 30 minutes both sides. Just the right wrench and you done.