Fusion 360 | Faceted Vase

Рет қаралды 15,642

Күн бұрын

Creating a faceted vase in Fusion 360.
The workflow shown in this video is based on the proposed workflow by daveBYYPCU on the Autodesk forum with some slight variations.
Link to the forum post:
forums.autodesk.com/t5/fusion...
Link to file with starting sketch:
a360.co/3WC0NIc
If you have found this video useful and would like to support me, you can buy me a coffee at
www.buymeacoffee.com/fusion36...
or you can also support me on Patreon at
www.patreon.com/fusion360scho...
Disclosure: Autodesk has kindly sponsored the full version of Fusion 360 that is used to produce the videos on this channel. That being said, Autodesk has no editorial control over the content on this channel. I am still an independent creator with the aim of creating videos that help viewers in using Fusion 360. These videos are not meant to promote Fusion 360 as a product.
#fusion360school
0:00 Intro
0:43 Revolve
5:10 Vertical strip
11:31 Circular pattern and combine
12:45 Decorative rings on base and other details

Пікірлер: 50

@Fusion360School Жыл бұрын

You might want to try experimenting with using a loft for the vertical strip and let me know your thoughts. Here's wishing everyone a good year ahead!

@Flygtraktor Жыл бұрын

This is the way to do it. No music, no drama. The relevant steps are shown without repetitions.

@Sun0faBeach1 Жыл бұрын

Probably one of the few contexts where saying "let's hide the body" doesn't get you into serious trouble :D

@alexanderfpv6655 Жыл бұрын

Love your videos. The stuff you demonstrate is always just outside my level of understanding - so I'm always learning new things. Nice job.

@adambergendorff2702 Жыл бұрын

WOW, I would have struggled trying to figure this one out! 99% of the parts I make are sheetmetal, but I learn so much wachting your videos, Thank You

@lovecastle7154 Жыл бұрын

Every single one of your videos I find myself saying “I didn’t know you could do that”

@JeffBradway Жыл бұрын

That was an interesting tip with the arc projection constaints. That could come in very handy. In this case you could also re-sketch an arc and make it co-radial to the original arc. (Maybe first projecting the original arc as a construction line. I forget if F360 allows constraints to non-projected geometry.)

@Fusion360School Жыл бұрын

Come to think of it, a better way would have been to sketch a centerpoint arc. With a centerpoint arc, I can start by clicking on the center of the original arc and then clicking on the top and bottom horizontal lines. And then dimension the offset.

@WMBayouLures Жыл бұрын

Awesome technique and explanation!

@beaugalbraith3242 11 ай бұрын

This is next level. Thank you

@johnnycomelately6341 Жыл бұрын

Very well done

@JoNorthkeeper 2 ай бұрын

Thx very good work.

@WPGinfo Жыл бұрын

🤓WOW very impressive! Thanks!

@mattiasfagerlund Жыл бұрын

Very clever!

@stephenedwards3397 Ай бұрын

Superb

@piranin666 11 ай бұрын

thx!

@chrisleech1565 Жыл бұрын

Thanks

@chrisleech1565 Жыл бұрын

Merry Christmas @Fusion 360 School

@Fusion360School Жыл бұрын

@@chrisleech1565 Thanks for the support again! Merry Christmas.

@rimbachfull Жыл бұрын

Hello excellent video as usual I just have a little problem I can't change the length of my project line

@Fusion360School Жыл бұрын

Hi, are you referring to the projected arc? An alternative way is to sketch a centerpoint arc instead. With a centerpoint arc, you can start by clicking on the center of the original arc and then clicking on the top and bottom horizontal lines. And then dimension the offset.

@EthanMitchell_YouTube Жыл бұрын

How do you add the rough surface texture to a solid at marker 15 seconds. Great videos! Thanks

@Fusion360School Жыл бұрын

I applied a rough powder coat appearance.

@EthanMitchell_YouTube Жыл бұрын

@@Fusion360School Would that come through if you were to 3D print the model?

@Fusion360School Жыл бұрын

@@EthanMitchell_KZfaq Unfortunately, appearances are superficial. They are just for rendering purposes. So they won't appear on the print. Does your slicer program have the ability to add texture?

@Fusion360School Жыл бұрын

I use Cura and I think there is a "fuzzy skin" setting. Haven't tried it out yet though.

@EthanMitchell_YouTube Жыл бұрын

@@Fusion360School You can add what is called fuzzy skin but it effects the entire model.is there way to add texture to a specific faces/surfaces in fusion 360 that is actually physically there and will come through in a 3D print?

@AnkaObezanka Жыл бұрын

6:26.... how did you get the project automatically?

@Fusion360School Жыл бұрын

Go to preferences -> general -> design. And activate auto project edges on reference.

@ChrisWard74 Жыл бұрын

I wish you included how to do the revolve to cut the inside of it.

@anthonyricci5380 Жыл бұрын

You just need to select the same profile at 15:18, then Create > Revolve, and finally set the operation to Cut.

@randybasil1715 Жыл бұрын

how do you design shoes in fusion?

@stevemcgraw7479 Жыл бұрын

Right at 8:03, where you hover over the endpoint for Body2(1), the body created from the 15 degree revolve. You cursor changes from an X to a square and allow you to snap the start of the line. Mine never does, it remains an X. Can't make it snap even with "Snap" ticked in the Sketch panel. Has anyone encountered this before???

@stevemcgraw7479 Жыл бұрын

I did figure this out. My default settings for Fusion 360 didn't have "Auto project edges on reference" selected. Once I toggled that (under Profile->Preferences) it snapped without any issue.

@Fusion360School Жыл бұрын

@@stevemcgraw7479 Yes, sorry that I did not mention this. This is a rather common question. I'm still trying to figure out a good way of mentioning this without being repetitive.

@samuelmorshed3364 Жыл бұрын

how did you drag the point to terminate the top edge? it wasn't locking on the edge whats so ever

@vladislava927 Жыл бұрын

I have a slight problem with the patching feature (as shown at 15:22). When I select the three lines to patch on top of the shape, my "OK" button is grey and I cannot press it to complete the procedure. Do you know where the problem could lie? I've already tried many things, but it stays and I cannot proceed with the design

@shabu49 Жыл бұрын

i have the same problem. I can only select the two front edges but not the back one.

@PierreMilcent Жыл бұрын

I am trying to reproduce your design, but when applying the patch function i can only select the straight edge 1 & 2 and not the curved one, either at the top or the bottom. So i am not able to close the body at the step. Any idea why this cannot be done ?

@redryderaus Жыл бұрын

Is it possible you have a gap somewhere? That may prevent the patch from working.

@PierreMilcent Жыл бұрын

@@redryderausi will check. How to identify a gap easily ?

@ianpendlebury3704 Жыл бұрын

@@PierreMilcent I haven't done this (yet). Maybe the mirror did not join the two surfaces?

@PierreMilcent Жыл бұрын

SOLVED : I think i found the problem : there is a gap indeed, it comes from the line during the sketch at 8'04".

@fotiskroi3048 Жыл бұрын

how the hell do I pick the line for the pattern in the beginning

@phakalanep7241 Жыл бұрын

Link to file with starting sketch: does not work - please fix

@Fusion360School Жыл бұрын

There seems to be a problem in posting a file without any bodies. I have reposted the file with the revolve. Please refer to the new link in the description. Sorry about this.