Honing / Deglazing a CRF50 Cylinder

Рет қаралды 13,567

3 жыл бұрын

After ditching the crappy Chinese knockoff cylinder I needed another. I picked an old stock cylinder on Ebay and the bore was fairly glazed. Time to learn and practice a new skill!
Affiliate Links:
Cylinder Hone - amzn.to/3qn2Q2x
Follow me on Instagram!
/ garageaddiction
Tees & Stickers:
teespring.com/stores/garage-a...
Music
Outro:
Retnik Beats | www.youtube/c/retnikbeatsbe/
(As an Amazon Associate I earn from qualifying purchases at no additional cost to you. This is a great way to support the channel!)

Пікірлер: 23

@86z50r Жыл бұрын

Thank you!

@TheChaz81 9 ай бұрын

Shit I'm definitely taking it to heart This is the only video I can find to show me how to do this It's all writing on you bud!

@jessebrown9046 2 жыл бұрын

I like the stick hones way better then flex, I tried a 320 flex hone on my DT200 cylinder and I had to take the topend apart because the rings didnt seat, it dropped to 90psi after a couple kicks, it was likely to fine of grit but I can hone a cylinder mint with the stick hone medium grit

@GarageAddiction 2 жыл бұрын

Yeah after running this one through I'm pretty pleased with it!

@willcountypowersports6338 Жыл бұрын

Nice little tutorial. The only thing I would recommend to stop the drill, decompress the tool and then remove it so it doesn’t fling out of there like that. And clean with soap and water until a white rag comes out clean

@GarageAddiction Жыл бұрын

Yeah good tip, I was a little concerned with stopping the hone in the bore but realistically it probably wasn't going to mess up the crosshatch.

@chriauc2976 10 ай бұрын

more oil constantly that what you need its called honing oil SUNNEN

@WilliamNyberg 2 жыл бұрын

pretty much my exact situation, 'cept mine's an XL100s. good stuff

@GarageAddiction 2 жыл бұрын

Ah nice, good luck with it!

@WilliamNyberg 2 жыл бұрын

@@GarageAddiction thanks UPDATE: it's back together, seemed to work perfectly, but now the carburetor gremlins have struck...

@GarageAddiction 2 жыл бұрын

@@WilliamNyberg Nice! Just need a carb clean perhaps?

@WilliamNyberg 2 жыл бұрын

@@GarageAddiction nah, it's jetting I think. brand new carb, see. (I also might have to fiddle with the timing)

@djnortz5449 2 жыл бұрын

Did you go in both directions on the drill or just one?

@GarageAddiction 2 жыл бұрын

Just one direction

@Bee-fr7zk 2 ай бұрын

I’ve sat here for a hour with that tool that did nothing lol

@tuntony8787 Жыл бұрын

What size of the stick for that size of cylinder, Sir!

@GarageAddiction Жыл бұрын

amzn.to/3qn2Q2x - 1-2.5 inch, this was the exact one I used. Cheers!

@robwinter3183 10 ай бұрын

Will this work on a 2 stroke cylinder?

@GarageAddiction 10 ай бұрын

Only steel lined cylinders, it’ll destroy a nikasil plated cylinder.

@lettuce953 2 жыл бұрын

Did it turn out good?

@GarageAddiction 2 жыл бұрын

Turned out great, runs like a champ!

@masonfrazee4039 Жыл бұрын

what brand honer?

@GarageAddiction Жыл бұрын

amzn.to/3qn2Q2x