A really good watch, a touch of realism was injected when it didn’t fire up, keep them coming.

That's so brilliant your friend from Egypt 🇪🇬 greetings

My favorite video segments is where you measured the thread pitch and then resized the bolt to M12 and pressed the bearing into assembly AND removal of the sheared bolts! Thanks!

Холостые большие, сцепление выйдет из строя раньше времени. На холостых режущая часть не должна работать(что на бензопиле, бензокосе, бензорезе с алмазным или корундовым диском и тд). С опора на поршне нужно было земенить(они уже разбиты), по хорошему вовсе поршень под замену, а цилиндр нужно было проверить на зазор колец в нем(если большой - замена), коленвал в подшипники нужно было садить на анаэробный клей(посадка просажена, убьёт со временем его). Короче ошибок простых хватает

My favourite channel bro

24:42 im glad to see that you're don't afraid show your mistake) it's strongly!

Great Job Sir. That valve thing inside the carburetor, is almost always bad... diaphragm, you called it.... Just plan on changing it..... It's always bad. They get brittle, they get messed up, they don't work....

Very good restoration 👍👍👍Thank you for sharing. Be safe🇨🇦

Youre amazing bruh. We are so lucky to have u here. thanks

This was very informative. I' ve watched many of your videos and the were always inovative and fun to watch. Very nicely done. Keep on!!!

I’ve watched your channel from the beginning. You are so interesting and your work is great. It encourages me to repair things…not to your skill level, but at least to have a go! Thank you

I found him some time ago and i love every video of his. One of my favourite channels for sure. I wish he uploaded videos more often. But i understand every piece needs its work and its not easy at all. Keep it going!!

Konitywa, Master! Thanks for video!

I loved watching how you working ☺

Наконец-то хоть в этом ролике он не устанавливает аккумуляторные батареи.

Your inspirational, I'll restore my own trimmer now. Good Job well done

Приветствую, люблю тоже реставрацией таких инструментов заниматься. Вам лайк 👍

good to see your face a bit. keep up the excellent videos!

Wow you are extraordinary and genius thanks sir for sharing this wonderful video.

Very good restoration

Very grateful work bro, and I have enjoyed the work, god bless you.

Nice job my friend congratulations

great work

Excelente video Gear Show

Genio. Muy buenos tus videos. Me encantan! Muchas feliciraciones. Saludos desde Argentina.

Second life,for old tools💪👍

I follow you from Egypt and I love your content so much

Exhaust close by gasket 🙄?... Nice job bro

i saw the gasket for the muffler and thought to myself... yep, been there, done that lmao

This should be a small engines repair video. You did a great job!

Thanks a lot for nice explanation.

My favorite channel, keep the good work man 👍🏻👍🏻

Gratidão GearShow!

Well done 👍

Çok güzel bir paylaşım olmuş 👍🤝🇹🇷

Great job, thank you brother. You are so talented

Exelente video son muy buenos saludos desde Honduras.

If you press Ball Bearings in like at 15:15 you should press them in at the outer ring. In you'r scenario the Balls had to translate a angular force to the outer ring. This will most likely damage the Ball s in the Bearing and can lead to a much quicker failure. But i think you know that, thats why you use a older Bearing ontop but just wanted to let ppl know.

Fantástico, que laburo !

Very wonderful one of the best channels I have to watch ❤❤❤❤❤❤❤❤❤❤❤❤

Good job👍

Very cool, well done. 👍

Nice job man

Cool

Прикольная пила😋 впервые вижу

한국분이셨군요 가끔 이 채널영상 봤었는데 이제알았네요...ㅎㅎ 구독누르고 가용

Muy bueno !!!!!

انت مبدع 🌹👍🏻

Ótimo trabalho 👏👏

I used to own the exact same one under a different name, which was called Moutfield

Vườn nhà đẹp quá!

What's the name of that small power tool your using

أحسنت بارك الله فيك

Absolutely amazing work my friend!!! You did an awesome job bringing this hedge trimmer back to life. My only question is why didn't you clean the carbon off the top of the Piston?

You don't usually break out big tools on your videos but this time they were big, very big.

very nice👍👍😘

What assembly grease do you use?

What are. You using for cleaning the parts.?

Gooooood~~~

Super

I have one of these but it called a T-Maker. Identical to your HT230. WhenI replaced the carb it ran ok. In your video the shears are moving after you start the machine on the bench, mine was the same. The shears are moving at idle, I have since been looking at videos to see if this was common, but I think not. This was part of the reason why I cut my finger badly, because the shears are moving even when not pulling the trigger. In your second start up on the grass I noticed the shears were not moving at idle speed, This way the machine is much safer to use. I will try to set my machine up so the shears don't move at idle speed. Are you able to tell me how you set up your machine in this way, do I tighten the bar screws? Great video, a fluke I have the exact same machine.

watching after 5 minutes video was released.

Love your videos, just wondering what's with the "gear show" watermark?

Nevermind... You caught it. Lol

Dam.... 10min to take i all apart 🤤

What about the exhaust gasket. No center hole?

Good ii boss 👍👍😊😊

Just realized these little machines must have a non-float carburettor (UK spelling). They work upside down!

I liked your threader set. Which brand is it?

i thought its a saw to cut wood but it seems i was wrong in the end xD never seen these tools in my life

Классные штаны у чувака в конце видоса-фИрма!!!

Was that epoxy that was holding those sheared bolts in? That gray stuff on bottom of bolts looked like dried up JB weld.

👍👍👍

👍💯

I wish I had access to channels like this when my father’s reciprocating saw needed restoration. It burned up, so I discarded it. (There was no internet back then).

Please convert petrol chainsaw to electric chainsaw with motor

How many of you were screaming at the screen when the muffler gasket was put on the first time? Heh! Good catch!

hi. I have been following your channel for a while. I love the restoration theme and I'm a fan of you. I am also doing a restoration channel and hope that you can give me some suggestions about my restoration videos. I'm really grateful.

Nice, But why u blocked the exhaust with the gasket xD 24:40

😮

Bel video bravo. MA TROPPA PUBBLICITÀ!!!! 😦

Niceeeeeeeeeeeeeeeeeeeeee

Would have been perfect candidate for DC conversion... :(

👍👍👍👍👍👍👍👍👍👍👍

13:45 Что-то пошло не так: и бензиновую технику стал обслуживать, и ёмкость для мытья запчастей стала больше, и воды больше использует.

Kênh này ở vn hả bạn

Great video but I do not understand why you don’ t replace the clutch and use original gaskets, it can’ t be that expensive…

Can you make glue gun cordless ?

OK

I think the engine is a Zenoah clone?

...ни какая это не бензопила!-, это бензокусторез!!!

Yeah more gas stuff.

the greese looks like curse d sweet n sour sauce

I wonder if you heard us all yelling about the exhaust gasket the first time you put it together before it had a hole in it. As if millions of voices suddenly cried out in terror and were suddenly silenced.

МОГО МОГО МОГО МОГО БЕНЗИНА КУШАЕТ УЖАСС УЖАСС О БОЖЕ.😱😱😱

I don't know why all trimmer come with lot of plastic pieces is not solid at all

It's only cleaning ! 🤣😂

21:59 😨 horror, beat with a hammer on a balanced crankshaft! The seat must be heated with a burner, and the bearings must be cooled, no force should be exerted on the crankshaft.

Bạc zin sao ko để sai

Very good job👍👏 Thenkyou very much!!!Send with Ukraine 🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦