GM 7.5 Upgrades and Install. Subscribe Here Thanks for stopping by Leave me a comment #gbodyrearend #gbody
Пікірлер: 110
@ssgang7773 жыл бұрын
Tight work bruh 💪🏾 looking good under there‼️ happy Father's day to ALL
@MRRANDOM13 жыл бұрын
Thanks Gods Image happy Father’s Day
@chevyrider2472 жыл бұрын
Well needed video my brother. I've been wanted to upgrade my 7.5.
@MRRANDOM12 жыл бұрын
Thanks my brother, I’m locked in! 💯🤝
@spraym882 жыл бұрын
I like this! Great video man. I need to do my axles. Glad I clicked on this
@MRRANDOM12 жыл бұрын
Thanks fam, I having an issue with the rear end sitting about 1/4inch to the passenger side Ima try adjusting the upper control arms hopefully that fixes it! 💯🤝
@robertkeenbuildingmylifesh34293 жыл бұрын
Salute, blessings always saving my life motivational.
@MRRANDOM13 жыл бұрын
Robert Keen 💯💯🤝
@jhewing66922 жыл бұрын
Good video. Thank you. now I am ready to tackle my rear-end
@MRRANDOM12 жыл бұрын
Thanks fam, get it done! 💯🤝
@LEFTY2GUNZ401twoGUNZ3 жыл бұрын
Yes sir my brother can’t wait till you done
@MRRANDOM13 жыл бұрын
Thanks fam 💯
@JohnBlaze-ff3lm2 жыл бұрын
🔥🔥I would of never attempted this but after this video I may try it
@MRRANDOM12 жыл бұрын
It wasn’t hard at all Fam just gotta get it down and go back up with it.
@MrVigor47 Жыл бұрын
Not hard at all just takes a little time but is well worth, I did have to change my proportioning valve.
@TeamSchaeffer3 жыл бұрын
💪🏾💪🏾💪🏾💪🏾💪🏾💯💯U doing great work bro
@MRRANDOM13 жыл бұрын
Thanks Team You Doing Great Yourself 💯💯💯
@johnmaxwell7533Ай бұрын
Found your video today😮 very helpful
@MRRANDOM1Ай бұрын
Thanks for the feedback, also glad I was about to help 👍
@deerealiist74113 жыл бұрын
Pfshhh pfshhh pfshhh bless up fam thank you for sharing this appreciated upload ☀️💯👼😁 have a bless day
@MRRANDOM13 жыл бұрын
Thanks GEE Blessings Fam 💯🤝
@CatlocosGarage3 жыл бұрын
Great vid bro.
@MRRANDOM13 жыл бұрын
Thanks Catloco 💯💯
@peggysmith84672 жыл бұрын
Nice work great video 👍
@MRRANDOM12 жыл бұрын
Thanks fam 💯🤝
@HeavyChevy19753 жыл бұрын
Puttin in work big dawg 💪🏽💪🏽💪🏽 happy Father’s Day
@MRRANDOM13 жыл бұрын
Tryna get it rite! Thanks fam happy Father’s Day 💯
@Mcdashiznit2 жыл бұрын
I needed this
@MRRANDOM12 жыл бұрын
Glad I was able to help fam 💯👊🏾
@willierebuildz91823 жыл бұрын
Yes sir looking good👍👌
@MRRANDOM13 жыл бұрын
Thanks Willie 💯
@ericwinston36513 жыл бұрын
Damn neph you getting that work in
@MRRANDOM13 жыл бұрын
Yessir Lil sumn
@drjoe2323 Жыл бұрын
Mr random you the man bro 💪
@MRRANDOM1 Жыл бұрын
Thanks fam 🫡💯
@Kayaan_thegreat Жыл бұрын
🔥
@MRRANDOM1 Жыл бұрын
💯👊🏾
@goldie_box29043 жыл бұрын
Good video 💪💪💪💪
@MRRANDOM13 жыл бұрын
Thanks Goldie 💯🤝
@robertkeenbuildingmylifesh34292 жыл бұрын
Salute to everyone grind and Motivations.
@MRRANDOM12 жыл бұрын
Motivation and Grind 💯💯🤝
@itsthamal93392 жыл бұрын
💪💪
@MRRANDOM12 жыл бұрын
💯💯
@alkrwchyh3 жыл бұрын
👍👍👍👍👍
@MRRANDOM13 жыл бұрын
💯❤️
@BLACKRAIN3903 жыл бұрын
GRINDING ✊✊✊
@MRRANDOM13 жыл бұрын
Gotta get back on the painting
@BLACKRAIN3903 жыл бұрын
@@MRRANDOM1 I GOTCHA BACK FAM,,,,JUS HIT ME UP!!! 🍻👍💪💯💯💯
@abackey13 жыл бұрын
Happy Father's Day Random
@MRRANDOM13 жыл бұрын
Thanks You can’t handle the truth
@lamarcusburston80522 жыл бұрын
Mr Randooommmmm good work man. I just had gears in my rear end and just install rear upper and lower trailing arms. I’m stuck cause I read in the instructions to tighten everything down when the tires hit the ground but the jack is under the rear end and won’t lift the car off the frame jack stands. What did you do? I can see why they say lower the car… so the rear end will level itself out.
@MRRANDOM12 жыл бұрын
Still.haven’t tightened the lower control arm and adjusted the upper yet but I will do it with the tires on the ground. Thanks fam 💯💯
@MrVigor47 Жыл бұрын
What's the wheel stud size you used, I need it for my upgrade??
@ericchris86552 жыл бұрын
Yo bro. Great video. Was curious if you were able to hook up the parking brake. Looking to do the same upgrade but want to keep the parking brake
@MRRANDOM12 жыл бұрын
Thanks fam I deleted the parking brake but it was easy to hook up I would have just needed the brake
@patrickmacord8725 Жыл бұрын
Great video! Are those Blazer or Camaro rear brakes? Looks really good. Give us a update video on how it stops.
@MRRANDOM1 Жыл бұрын
Thanks. Blazer Front and Rear. Stops on the Money 💰🫵😜
@iiNgONYaMa Жыл бұрын
@@MRRANDOM1 s10 blazer?
@Burdysc Жыл бұрын
@@iiNgONYaMa yes s10 blazer. 98-04 will work
@BigRichEHhthang1003 жыл бұрын
Yeah unk
@MRRANDOM13 жыл бұрын
💯🤝
@ebritanica2 жыл бұрын
Good job. Check mine too.. Caprice 1992 complete conversion kit with modern gm opel insignia trw calipers with emergency brake and w221 mercedes rear disk brakes. Plates are made from scratch by myself. All parts are domestic buying and new, except complete used rebuilded calipers from domestic partshop. More info on impalassforum in brakes category: 300mm rear disk brakes...
@MRRANDOM12 жыл бұрын
Nice Build fam keep up the great work 🔥🔥
@ebritanica2 жыл бұрын
Thanks. @@MRRANDOM1 i can repeat it 1001 times. But need very simle axle machining and disk brake redrilling to 5x127 bolt pattern. Can make it on 300, 315, 320, 330 and 345mm rear disk brakes. Axle machining kzfaq.infoQbA1RtPoDug?feature=share
@ibiusgroup28272 жыл бұрын
Do you have an extra set of the jimmy rear brake line brackets?
@MRRANDOM12 жыл бұрын
No I don’t sorry
@bjsearles44092 жыл бұрын
Good video bro! Where can I find those Red bushings?
@MRRANDOM12 жыл бұрын
Thanks fam, EBay
@ibiusgroup28272 жыл бұрын
What was it you was welding? Will the gbody stock break lines work with this conversion?
@MRRANDOM12 жыл бұрын
I was the brake line mounting tab. They will work just need some massaging, I think I kinda made a lope In the stock hard line, then connected it to the rubber line where the tab comes in, hardline may be a little long
@ibiusgroup28272 жыл бұрын
I like to start by saying you are the man. How did you get the break line brackets off the blazer? I just finished the front and working on back. Did you have to change master cylinder to the blazer as well?
@MRRANDOM12 жыл бұрын
Thanks @@ibiusgroup2827 I unbolted the off the front I believe and cut the bracket down. I used the factory booster.
@ibiusgroup28272 жыл бұрын
How much would you charge to upgrade g body brakes to blazer brakes?
@MRRANDOM12 жыл бұрын
Too much on plate
@MrBhustle3 жыл бұрын
Happy father's day
@MRRANDOM13 жыл бұрын
Thanks Mr Hustlehard happy Father’s Day
@arminplummer6843 Жыл бұрын
What is the part number for the studs for jegs
@MRRANDOM1 Жыл бұрын
I ordered them from Jegs
@michaelfreeland54542 жыл бұрын
Nice mane, what brake lines do you go with? And what size studs did you use?
@MRRANDOM12 жыл бұрын
I used the stock Montecarlo lines just curled the ends. Welded the mount to the rear end. 2-1/2 inch studs from summit racing . 2” is enough
@michaelfreeland54542 жыл бұрын
Thanks for responding I’m doing the same setup now
@MRRANDOM12 жыл бұрын
Nice I’ll check out your channel
@michaelfreeland54542 жыл бұрын
Hey Sir, had another question, did you need an adapter piece for the rear axle hard line to the soft brake caliber line to be hooked up or they connect with no problem?
@stevefranklin99208 ай бұрын
What calipers and backing plates did you use?
@MRRANDOM18 ай бұрын
02 Blazer
@stevefranklin99208 ай бұрын
@@MRRANDOM1 gotcha! I saw a video where a guy was showing how to put C5 or C6 brakes on the front of a G body using '02 2wd Blazer spindles and aftermarket brackets.
@BillyRay501 Жыл бұрын
Was u able to use the same brake lines and brake booster?
@MRRANDOM1 Жыл бұрын
Yes
@MRRANDOM1 Жыл бұрын
Recently upgraded the front to Russell
@BillyRay501 Жыл бұрын
@@MRRANDOM1 brakes?
@MrJose1237042 жыл бұрын
What car are the backing plates from?
@MRRANDOM12 жыл бұрын
98 - 03 blazer
@user-sz2nn2vr5q Жыл бұрын
Hey can you tell the parts # for the studs that you used
@MRRANDOM14 ай бұрын
Jegs studs
@BluuSmurf Жыл бұрын
Bro how you get the upper arm bolts out what did you use to get in the tight space
@MRRANDOM1 Жыл бұрын
Magic 🤣
@BluuSmurf Жыл бұрын
@@MRRANDOM1 lmao I’m about to get them shits out today
@MRRANDOM1 Жыл бұрын
I used a socket and extension to get in the hole of the frame, I think that was for the lower. The upper I used a wrench I think and air impact for sure, air chisel work good to, the stuff moving as well. Use penetration oil to help also
@BluuSmurf Жыл бұрын
@@MRRANDOM1 i was trying everything it kept falling off the back but i just cut the bolt off lol good looking out bro
@MRRANDOM1 Жыл бұрын
I think I do remember cutting a bolt I’m not sure it was a while ago 💯👊🏾
@carmelnanez26252 жыл бұрын
Got a part number for those wheel studs???
@MRRANDOM12 жыл бұрын
I got them from summit racing they where the cheapest I’ve live around $40
@lsbackyardbuild16732 жыл бұрын
@@MRRANDOM1 you remember the part number
@iiNgONYaMa Жыл бұрын
That's a posi? Can you put posi gears in?
@MRRANDOM1 Жыл бұрын
Yes , Yes
@shaun4bigblocks9939 ай бұрын
In my opinion it kind of defeats the purpose of the video to not go over the parts used. Like I am assuming you used a F-Body rear disk setup but from what year? Hou should add fine details in the crotch box to make this go from a "look what I did, Mommy" video to a "How-To" video. You tracking??
@MRRANDOM19 ай бұрын
What
@elreyyakko5 ай бұрын
@@MRRANDOM1 he wants a parts list of what you used
@MRRANDOM15 ай бұрын
@@elreyyakko I used 98-02 blazer front spindles for dual piston calipers and for rear i used back plate from blazer as well with the calipers. Jegs wheel studs and BMR Rear suspension kit
@queezytarantino14564 ай бұрын
@mrrandom1 What is the part number for the studs you used bro?