Noise When Taking Off In 1st Gear & Reversing

Noise When Taking Off In 1st Gear & Reversing - Found & Fixed

Рет қаралды 472,752

2 жыл бұрын

In this video I show how I found and fixed a clunking noise when taking off.
Thanks to everyone who watches my videos, Likes, Shares and or leaves a comment.
I appreciate everyone of you.
If I helped ya out? or just enjoy the content & you would like to buy me a drink ➢ ko-fi.com/gerardburke
Tool options that I personally use & recommend ➢ www.amazon.co.uk/shop/gerardb...
➢ For business inquiries Email : gerardburkebusinessinquiries@gmail.com
Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.
popping noise when taking off from a stop
front end noise when accelerating from stop
noise when going in reverse
noise when changing gears
single clunk when accelerating
transmission clunking when accelerating
driveshaft clunk when shifting
knocking noise from driveshaft
cv joint noise
tripod joint failure
how to diagnose a driveshaft noise
noise when taking off at the traffic lights

Пікірлер: 197

@michaelbixler87 2 ай бұрын

“Load shifting” Thank you! I've been searching for over an hour looking for exactly what term you call this issue Nailed it!

@SyFyBry 2 жыл бұрын

@Gerard Burke I’ve been looking for someone to address this noise under these circumstances for so long!!!! Thank you

@willesco5211 2 жыл бұрын

You are a truly Master Mechanic Technician...........

@MiracleMAX 2 жыл бұрын

Proof of customers' complaint is a vital part of successful diagnosis. You are right, some do their road test and after that it's guesstronics and load up the parts cannon. That joint was pretty cooked! I don't think I've seen an inner that bad before. That noise must have been there for ages. It would have been a real mess had the joint finally broke free! I don't think the dust boot would have held it in place. 😁 Thanks for sharing! 😊

@GerardBurkeBurkesGarage 2 жыл бұрын

Thankfully it didn't, would have been a bad experience for that customer if it had 😐 We just got there in time 💪🔧⚙️🔩 A much safer vehicle on our roads for everyone 🚗 Thanks for tuning in mate 🙏👍🙏

@PL-fc6hm 2 жыл бұрын

thanks for another video. these days is very hard to find a good mechanic. the first garage clearly didn't even know the basics.

@stefanhearn430 2 жыл бұрын

Have this exact same noise. This video definitely cleared my train of thought. Great video.

@MustafaMohammed-ru1mk Жыл бұрын

Great video always a pleasure watching. Thank you

@chevaliercognac8757 11 ай бұрын

Nice work and video - short and clear!

@cosimodalessio642 Жыл бұрын

Clear and concise video! Thanks!!

@shazamshazam7929 Жыл бұрын

Wow so easy and precise explaination great job.i changed so many parts of my mazda3 like shocks mounting but I know understand from wer that noise is coming .appreciate sir thanks

@raymaharaj3555 2 жыл бұрын

Excellent visuals ....thanks

@cjra8235 Жыл бұрын

Amazing..thank you..I drive an automatic transmission Honda fit 2010 and it does exactly the same sound as shown on your video..got scare thought it was my transmission...lol

@chrisellejohnson8522 2 жыл бұрын

Great detailed video

@malihaorfani 2 жыл бұрын

Hi your one of the most vise tach , we are thanksfull of you.

@Abdul-mh5zh Жыл бұрын

Thank you so much for video!

@TonyMontana-xf8fr 26 күн бұрын

Excellent work. Most useful information i ever seen pertaining to inner cv.

@heavyh13 Жыл бұрын

Thanks, Gerard Burke, for the recurrent training

@GerardBurkeBurkesGarage Жыл бұрын

Thanks for the kind words, much appreciated 🙏🙏

@user-cz8lv9uq3d 5 ай бұрын

❤ like it cause it gives a healing peace of advice on what I can fix that problem also know it straight away

@DunOpondo Жыл бұрын

Great video 👍🏿

@noumanchoudry3147 3 ай бұрын

Love a mechanic making a short to the point video 👍 have to subscribe to your channel.

@user-oq9rc3ej9l 4 ай бұрын

Omgg i been going through this for a few months everybody keep saying CV axle but this is the exact noise im getting 🤦🏽‍♀️ Thanks Im going to show this video!

@castrolgtx5064 2 жыл бұрын

Thanks for sharing Ger💥🍀 last time I came across this problem was in a Fiat Ducato many years ago… we didn’t replace the driveshaft just the hardy spicer only.

@GerardBurkeBurkesGarage 2 жыл бұрын

Not a common fault to come across but a good one to remember 👍 Thanks for watching Eric, always appreciated 🙏

@jithin1518 Жыл бұрын

Thank you…! Great video

@la3102 3 ай бұрын

Very clear video, thanks Dai

@GerardBurkeBurkesGarage 3 ай бұрын

🙏🙏💪💪

@bythesea2784 2 жыл бұрын

That was perfect how to easily identify this kind of problem thanks to your video it's help me very well keep on making this lovely videos to help people in this awkward situation

@patkelly7999 2 жыл бұрын

Great job and tip Gerard, Thank You:):)

@GerardBurkeBurkesGarage 2 жыл бұрын

Thanks Pat 🙏🙏🤗

@manuelmagalhaes8186 2 жыл бұрын

Very informative thanks very much.

@GerardBurkeBurkesGarage 2 жыл бұрын

Thank you Manuel, I appreciate the kind words 🙏👌🤗

@shawnpa Жыл бұрын

Excellent use of camera in diagnosing. I want to look into doing that.

@hollysalazar1062 Жыл бұрын

This video was so helpful! Do you have any videos on, my truck only makes a loud noise when I pull into reverse and when I drive an idol it makes a sound like something is circling and it needs more lubrication?

@jgeorges3061 2 жыл бұрын

AWESOME thanks for sharing.

@GerardBurkeBurkesGarage 2 жыл бұрын

Thank you 🙏🙏

@legrognard6699 5 ай бұрын

Great stuff

@robertsarabia7801 2 жыл бұрын

Thank you for showing the mechanics of this problem ! I am getting a loud clunking with my 5th gen Camaro . I’ve had previous problems with the thrust washer and axle nut but it sounds a lot worse now.

@adriontaegraydon1031 Жыл бұрын

Did u ever find it? Same problem with my 5th gen

@asianarw 11 ай бұрын

Same here , i have a 2018 Camaro SS

@LookInDJProduction 2 жыл бұрын

realy great info about symptoms, and video very good ..thx

@GerardBurkeBurkesGarage 2 жыл бұрын

Thank you

@user-wf8wl8mc5c 3 ай бұрын

Thank you for your helpful video. 🙂 👍🏼

@GerardBurkeBurkesGarage 3 ай бұрын

🙏🙏👌👌

@henrysevilla15 2 жыл бұрын

It's exactly 💯❗❗❗ thanks.

@freddyn2254 Жыл бұрын

Perfect 👌

@s.a.mdaniels1545 Жыл бұрын

That was great. Thank you

@GerardBurkeBurkesGarage Жыл бұрын

Thanks very much for the kind words, appreciate it.

@phumlanibrian8366 2 жыл бұрын

Dude you are the best 🏆

@GerardBurkeBurkesGarage 2 жыл бұрын

🙏🙏

@sasindudinusha3847 6 ай бұрын

Legend 🫡

@2013Start 2 жыл бұрын

Thank you.

@tsbkttkr Жыл бұрын

Great presentation

@GerardBurkeBurkesGarage Жыл бұрын

Thanks 🙏

@Salvatore3333 2 жыл бұрын

Hi Gerard, i just got the 4 engine mounts replaced and the mechanic didnt tell me about this, i have a rattling noise when moving off in 1st gear and reversing, parking etc... low speed vibrations, they did replace the driver side drive shaft both inner and outer boot so i guess they should have detected if it was the drivers side drive shaft so my guess is,,,since they did nothing to passenger side drive shaft then the near side drive shaft must be the culprit..correct? please tell me what you think.

@antof1235 2 жыл бұрын

Thank you again ☘️☘️☘️great, fully explained tutorial.

@GerardBurkeBurkesGarage 2 жыл бұрын

Thanks Anthony, very much appreciated ☘️ :)

@antof1235 2 жыл бұрын

@@GerardBurkeBurkesGarage I miss the stone walls from your old test drives☘️☘️

@GerardBurkeBurkesGarage 2 жыл бұрын

@@antof1235 🤗 and I do some days as well 🇮🇪 (not the rainy test drives 🌧️☔🍀😅)

@antof1235 2 жыл бұрын

@@GerardBurkeBurkesGarage 😂😂🙏🙏☘️☘️

@emma-je6ty 2 жыл бұрын

Question. I hope you see this, but my smart car fortwo makes a squeaking noice when I am in reverse aswell as just driving down the road/whenever I push the breaks, it may be just the break pads except that it squeaks even while I’m going 40mph (on and off with squeaking past 40mph)but I wanted to see if you could confirm. I have videos of the noise

@sollykhan2385 2 жыл бұрын

awesome video, thanks for sharing this, please do more 🙂

@GerardBurkeBurkesGarage 2 жыл бұрын

Thanks 🙌🙏

@sollykhan2385 2 жыл бұрын

@@GerardBurkeBurkesGarage LEGEND 😇

@DJManny254 5 ай бұрын

Earned a sub

@WuTangChillaBee Жыл бұрын

What about a rattling noise only when under load in reverse? No noise if i let off the gas... Many thanks for any hints!!

@DiamondScuff 2 жыл бұрын

How did you get it so the driveshaft would rotate. I would like to perform the same test thanks.

@delanacastevens3933 Жыл бұрын

Thank you

@hcs.media.720 2 жыл бұрын

Thanks now i know my problem

@andyd1006 Жыл бұрын

My 2002 F 350 super duty 7.3 liter diesel 6 speed manual does this. When starting off from a dead stop. Also on and off the throttle. I'm thinking drive shaft u joint or one of the front axle u joints. What are your thoughts. Thank you

@martinbadzo153 5 ай бұрын

Thanks

@duas7799 2 жыл бұрын

What you can tell me if my truck have the same problem but is in the rear wheel driver side

@jurgeenhandazola3006 Жыл бұрын

I have a similar problem, and CV axles are fine, ¿will this be related to transmission mounts?

@manjunathreddy1773 Жыл бұрын

My Q5 is giving me glow flash error and terrible black smoke. I have already got the EGR cleaned but no joy. Please suggest what could be a permanent fix . Thank you

@samotszriagencija8933 Жыл бұрын

I have octavia mk3 FL 2017 1.6tdi , I have approximately the same symptoms, only a little milder, is it possible that it's the sound gearbox, or the joint

@wrkls_ 2 ай бұрын

I’m having a similar sound going on intermittently when I change the position of the gear selector usually when going into reverse park and drive. It’s hard to tell where it’s coming from by myself but when I open the door it sounds as if it’s coming from the back side.. Before this I had been trying to diagnose another issue which is a noise or similar clunk that I’m getting from the front driver wheel. I can feel it when I’m either releasing the brake or pressing on the brake when changing direction. Only at very slow speeds. I suspect either the FL lower control arm and bushing or something to do with the front brake pads or calipers. But now that I am hearing this I’m not sure. Could it be the CV?

@eruerahardman6776 Жыл бұрын

So my 96 primera is an automatic and when I take of and it goes to shift into 2nd from first it clunks hard out. Would it be the same

@shanemcgovern2204 2 жыл бұрын

Well diagnosticed,strange there was no vibration on open road driving.. Great video

@GerardBurkeBurkesGarage 2 жыл бұрын

Cheers Shane 🙏 Customer never mentioned one (as they didn't notice any difference) and at lower speeds there was none present with my test drive. I also suspect at higher motorway speeds a vibration of some sort would have been felt with how unbalanced that shaft had become.

@arifeewanazman6531 2 жыл бұрын

force are applied in one direction, while the wheel was driven by the inner cv. Could braking cause this clunking noise while decelerating?

@danielpromero 2 жыл бұрын

@@arifeewanazman6531 yes that is what happened with mine. It would do the noise when accelerating and braking

@tupapi6989 Жыл бұрын

I have have this same issue on my 2020 Toyota Camry Se . It happens most when i shift into reverse, i csn heat the metal clunking noise. How much does it cost to get it replace?

@bradmadeira6807 2 жыл бұрын

Will it make that noise when letting pressing and when letting off on the gas pedal

@pillaroffiretv8850 2 жыл бұрын

Thank for sharing this great information here God bless you

@emaxxracer9931 Жыл бұрын

My 2007 Scion tC acts like this - clunk shifting forward to reverse and vice versa. CV axles were not worn like this but boots were tore so I replaced both. Actually replaced the left one two times since I thought the clunking was from it. The noise persists. I think it’s in the transmission now. How can you help me here?

@tekasaiservices Жыл бұрын

Thank you for sharing such an exclusive video on this issue. In my case I feel a jerking (no metallic clicking as you have demonstrated in this video) only when the gear shifter moves from drive to reverse. But when I move the shifter from reverse to drive then there is no jerking at all. What could be the possible causes in my case?

@muhammadhashimirshad1208 Жыл бұрын

Same question

@jjfernandez5044 Жыл бұрын

did you ever find out ? i have this problem too on my 05 maxima

@dinvenalbert5862 Жыл бұрын

Good evening sir I'm from Cameroon I have a similar nice but I have changed the shop RAV4 2001 and I still have the same problem so what can I do

@clintonbirdsr.8598 Жыл бұрын

09 chevy equinox does that. When put it in reverse or drive, theres a click noise on front wheel drive. My thought was drive shaft end that connects into the transmission. Is there a bearing or seal there that would do that in the tranny? Just happens on driver side.

@jesuszuniga1257 Жыл бұрын

Hi I have a 2012 civic lx sedan with 190k miles . What can cause a grinding noise when shifting from park to reverse and drive. Doesn't make the grinding noise when driving on street or highway

@ateeqafzal4444 Жыл бұрын

My 2011 ford ranger manual transmission is making a hissing sound when Im in neutral and move the shift lever all the way to the right as if I’m going towards reverse or 5th only makes this noise in neutral I’m confused any idea what it could be

@remus-liviudragaescu9870 5 ай бұрын

hello, I have the same problems, I have a volvo xc60 from 2010, front transmission, automatic transmission, when I switch to R, it does the same thing as yours, is it the same problem?

@FKNSENDIT Жыл бұрын

Think that is the exact sound mine in making 2020 hd8 thank u

@eduardofortini4633 Жыл бұрын

I just bought a new 2022 Chevy Blazer 3.6 L last September. In a couple of ocasions I had a weird noise shifting in reverse when parking. The car has 2000 miles. I hope that when I take it to Chevy for the first oil change, they will be able to scan the problem.

@shazilanwar7502 7 ай бұрын

I have watched your videos i am facing the same loud clunk noise when i shift from reverse to 1st gear and turn steering left then it makes a loud clunk noise which feels on floor. Even when I reverse it and turn it makes same noise. I have Suzuki Aerio/Liana 2006 model. All suspension done but the noise doesn’t clear.

@jessieurgea9899 Жыл бұрын

I have A 2016 300 3.7 Chrysler 300..I have a Clicking noice coming from under the Transmission different then the noise on your Video; It started going in Reverse only; Now its doing it when I drive Forward!! Any tips???

@adrianstacey5484 2 жыл бұрын

Hi, Excellent descriptive video, I have a Skoda Fabia Vrs 2006 1.9tdi I’ve got a clunk when changing gear mainly at lower speeds. I have a quick question, in this car was there play in the driveshaft when stationary ? As I’ve checked both driveshafts and there is zero play? I intend after watching this video to jack my car safely and get a friend to change gear. Much thanks Ade

@livinlifeat60mph 2 ай бұрын

Hey, were you able to diagnose this?

@leopard2008 Жыл бұрын

I have 2014 Durango, automatic transmission. the clunk sound is only when deceleration from 3rd speed to 2nd. Can you help?

@drrobert2120 2 жыл бұрын

Thanks great troubleshooting!!!👍👍👍👍

@GerardBurkeBurkesGarage 2 жыл бұрын

Thanks very much 🙏🙏

@islergucler4470 Жыл бұрын

Hi Gerard, I have the same axle movement on my BMW X5. I recorded this with my camera and added it as a (short) video to my KZfaq channel. Please, if you watch it, do you see the same issue? Thank you very much!

@deejay4837 4 ай бұрын

Was there play in the shaft when you grabbed it??

@sherrehman3316 Жыл бұрын

My Vehicle Corolla noise when press acceleration in neutral Gair.what is reason? Please tell me regarding of these issue.

@bandenaccount Жыл бұрын

If my car is FWD and is having the exact same sound under those conditions, could it be a front axle?

@munkhtsogtemuun8831 Ай бұрын

Hello i have a 2010 vw tiguan whenever i switch gears it makes loud clunky noise like this any solution?

@andrewcarey2674 Жыл бұрын

I got a similar problem knocking when pulling away in fist and second but sound like maybe coming from the gearbox I changed 1 drive shaft can you be off any help please

@randomjack477 2 күн бұрын

My car has the same problem in slow 1st gear and Reverse gear, but with a Clack Clack sound is it probably the same problem?

@tigarrtaz Жыл бұрын

Really appreciate your videos, do you think it will be the same issue if it only clunk's going into first or would that be something else

@caitlinmilewski620 Жыл бұрын

Did you find that out?

@tigarrtaz Жыл бұрын

@@caitlinmilewski620 turns out it was the gear stick, sticking. I've stopped parking on a hill and problem seems to have solved its self

@tigarrtaz Жыл бұрын

@@caitlinmilewski620 or the rear breaks, one or the other lol

@georgegirgis6435 Жыл бұрын

Hi there , Same sound but only once at start ( on and off ) at start and only on going forward

@Adam.minyan 2 ай бұрын

Is this an automatic gear car or a manual?

@itsuplike9947 Жыл бұрын

I have vibration only in drive or reverse gear when idling and when i take off at lower speeds i hear a rumbling that kinda sounds like my tires are falling off the wheel but it’s definitely the engine or transmission

@jordanmercier3616 2 жыл бұрын

Lmao, I've had this issue on my vehicle for like a year and a half and this whole time I thought it was an issue in the driveshaft because my vehicle is known for having a clunk in the driveshaft. I'm in the middle of changing the CV and I stumble across this video just watching random things. I can't believe this may have been my issue all along.

@honestone490 6 ай бұрын

This video shows It was indeed the drive shaft on this rear drive vehicle that was the culprit. The equivalent on a front wheel drive vehicle would be the cv axle. This vehicle in the video had a very badly worn drive shaft. The driver ignored this issue way too long. If they had caught it sooner possible only the u joint could have been replaced and would've been less costly a repair for the customer. In your case, with a front wheel drive vehicle if you catch the problem early enough sometimes only the boot needs to be replaced and if it deteriorates further then it's the cv joint or later the entire cv axle which needs to be replaced. The master mechanic should have explained these differences better when it comes to rear drive vs front wheel drive vehicles. He could have offered better advice on saving money for the consumer by catching this common place problem sooner rather than later.

@chevr6887 2 жыл бұрын

I need help my Audi s3 2015 is clicking when I turn the steering especially on the drivers side and it’s making clunking noise aswell which is annoying

@nozimanzi4020 Жыл бұрын

I also hear noise on my Volvo S80 2.5t, first I was told that it's a time belt. They change the whole thing#tensioner but the noise continued and now it's too much This time I was told it's the gearbox. What could be the problem?

@johnwoolfrey5093 2 жыл бұрын

Thankyou /John

@GerardBurkeBurkesGarage 2 жыл бұрын

Thanks for watching John 🙏🙏🤗

@BLACKPURP_4.6 2 жыл бұрын

I have this problem on my 08 mustang v6 and the gears are kinda stiff sometimes so i think its the drive shaft

@horaciogaztambide8565 4 ай бұрын

I replaced the cv axel in my 2015 mazda cx9 and it's stil making clicking noise when i accelerate from a stop and take off

@12vLife 2 жыл бұрын

My FWD 4 cylinder van got stuck in deep sand last month. Trying to get out it made some nasty popping noises. A few weeks later I noticed it makes a single popping noise now sometimes reversing or driving out when parked for a while. it does not make the noise when the van has been driving for a while. What's the best way to diagnose this?

@fluffycat6489 Жыл бұрын

I have a similar problem did you find out what the noise was? Mine only does it when it's cold.

@12vLife Жыл бұрын

@@fluffycat6489 Mine was the transmission engine mount. Swapped and it fixed it but seems I damaged again with another minor offroad incident where I bottomed out in sand. Seems the one in my 2018 Promaster city is made out of very fragile rubber.

@user..Aa..Bb.. 7 ай бұрын

I think this could be the same noise. Clunk noise when setting off and when change to second gear but your right a load shift type noise. I thought it was mounting and a mechanic said he coudnt find anything. This could be the fault. Thank you

@nishanishu4894 2 жыл бұрын

Car pulling problems full deatalis please

@travisparker7804 2 жыл бұрын

getting out of the army in 6 days, i can do it myself but don't want to take the job on at this moment. i believe i have this exact problem the broken bearings in the joint. do you think it's safe for me to take the drive?

@quintenelijah6586 2 жыл бұрын

I mean I do have Gods angels with me and anoint my car to keep me safe and I’ve been driving my car with these issues and more perfectly fine for months. But you should also be fine

@charlesroybal4764 8 ай бұрын

I'm running into this same thing. I just wanted to be sure if there is anything else that could cause those same sounds when going into reverse and driving forward?

@honestone490 6 ай бұрын

In some instances, it can be a transmission solenoid issue and checking the water pump as well for leaks is always a good suggestion. Be leery of mechanics who immediately recommend replacing the motor mounts which may not actually need to be replaced.

@bamgy1 11 ай бұрын

THANK YOU FOR THE VIDEO. BUT I HAVE CHANGED THE U JOIN 3 TIMES UNDER ONE MONTH IT KEPT BROKEN TIME TO TIME AND THE NOISE HASNT STOP AFTER EACH CAHNGE

@motanel Жыл бұрын

Hi I have a question. I have a loud noise when accelerating, if the acceleration is louder it is louder, if I reduce the speed the noise decreases. Can the driveshaft break if it is new (aftermarket)? I mean the noise is very loud? Can you please answer? Thank you 😊

@autogirl53208 Жыл бұрын

Would be nice to explain the noise...there are lots of diff noises. Humming?