Love the honest and sharing in hopes that others can learn from your mistakes ✊… FYI, you don’t have to change between phase 1, and phase 2 the only reason for doing that is to place the camshafts in a non-tensioned position. If you lineup, your right bank, your left bank and your drive chain and have all of the marks correctly then you will be lined up correctly for timing (as long as you are on the compression stroke)… if you don’t use the cam holders and don’t change the phase you just might have to manually turn the camshaft to get the left bank chain on the markers correctly . This is not advised because the cam can free spin to release tension and be a knuckle breaker lol …The right and left chains have to be 10 links between the intake and exhaust cam sprocket marks and the main drive chain is 17 chain links…. One last thing one mistake a lot of people make when doing phase 1 to phase 2 is that they don’t realize they have to turn the crank an additional 360° when REMOVING the chains to keep on the compression stroke, but then when reinstalling the chain, you just have to turn it to the next mark. 🧐
@FoolsAmongUs4 ай бұрын
I tip My hat to You Mr. Bilt's. There are two T's that I will never mess with, on Any Vehicle..............The Transmission, and the encased Timing Belt. You are Brave for attempting this project.
@dwreed63 Жыл бұрын
This guy is hilarious! Thanks for the great video. This was highly entertaining and certainly informative 👍🤙🍻
@josephrutz42482 жыл бұрын
Thanks Mr./Mrs. Bilt ! I enjoyed your adventure and admire your intestinal fortitude to learn, overcome all obstacles and succeed in your quest for accomplishment. You deliver many good lessons in this video and are quite inspiring. Well Done !!
@fd9431 Жыл бұрын
Done a few timing chain jobs gm 3.6vvt motors. No way I could do job with motor in vehicle. Thats impressive man. I include head gaskets with the job. Take heads to machine shop square and inspect valves and seals. Machine shop remove about 5-7 thousands off head, has been about average. Hasnt caused interference issues. Lastly clean up the mega amounts carbon from pistons. Sounds like a lot but not bad really. But again I pull the motor. Dont have a lift and pull motor out front..take off grill, bumper, radiator, condensor, etc etc. Not terribly involved but tedious. Time consuming. But knock on wood worked out so far. Thanks for posting vid.👍
@knock9045 ай бұрын
Yea sum timing jobs are best did with engine out like factory 🏭
@Poaf-17 ай бұрын
Gotta be a record for redo’s 😂😂😂😂😂😂😂lol 😂😂😂😂😂😂😂😂😂😂😂. You are officially a shade tree mechanic now 👍
@johnw302 жыл бұрын
Don't be hard on yourself. That is a huge job. The engine it suppose to come out of the car. It can be done in the car as I'm sure you know. I have been an Mechanic for 35 years and i have screwed many time.That's how you learn.
@mr.biltsgarage48322 жыл бұрын
I've always been my biggest critic in the situations I care about
@johnw302 жыл бұрын
@@mr.biltsgarage4832 I think everyone is. I know i am.
@curtisgore16119 ай бұрын
Hats off to you dude! Stay with it
@PaulRevere130am4 ай бұрын
Dude you forgot the upper hose clamp on the inlet hose. And by the way why it kept jumping timing on you was because the chain tensioners were not pumped up with oil pressure yet and the spring they put in them is just to hold enough tension to put the chain on and have it stay in place long enough to get the cover back on. On this specific engine I ALWAYS soak the tensioners over night in clean oil put them in the oil then pull the pin out and let them suck in oil over night rather. Yes they are a complete mother fucker to compress to out the pin back in but it is worth the colorful language you will learn during this process and ALWAYS USE AN A/C DELCO OIL FILTER the other filters will allow your tensioners to bleed off over night and you run into that problem once agin and change the oil every 2600 miles religiosity not the 5000 miles hat they say you can run them because that is complete bs all the way. Yea gm. I said it so 🖕🏼. And you will be good to go for many miles. Safe travels my dudes Oh and one more thing i forgot to mention to GM 🖕🏼🖕🏼🖕🏼🖕🏼🖕🏼. Have a wonderful day fuckers
@kw57rx8dr.92 жыл бұрын
If it's like mine the valve cover seals will leak if you didn't use silicone which you're not supposed to have use, but that's probably what is leaking down the back, I hear they're notorious for that.
@scarter9447 Жыл бұрын
Well done bloke. Im learning from lots of vids to do mine..
@axlejohnson91562 жыл бұрын
With any RTV, you must strip all the oil off all the surfaces. Clean them real good and then clean them again. Spray brake cleaning solvent seems to works the best.
@AGuysGarage Жыл бұрын
Sir my grandpa was a hard man, and he told me when I was young he said boy sometimes your butts going to itch. If you fail to scratch it well that's your own fault.
@jerbear795210 ай бұрын
What in the heck are you on about
@CowboyBleepBlop2 жыл бұрын
Not a relief cam but it's a direct injection engine so that exhaust cam on the left bank drives a high pressure fuel pump
@mr.biltsgarage48322 жыл бұрын
Yes I'm learning as I go Thanks
@dpipiles Жыл бұрын
awesome tips, going to try my first one soon
@TheMenace173 Жыл бұрын
Have fun Take your time Learn as much as possible
@kw57rx8dr.92 жыл бұрын
You don't need the top dead center tool on a simple (?) timing chain repair do you? Only if you are changing cam phasers? I'm on my third time on a Cadillac CTS 3.0L and I think I may have mine correct this time🙏, it's so easy to do on a table where you can see the timing marks well, stupid Gm to put them on the bottom of the crank, but even still I've never seen one of these where it was running afterwards in the videos to know if they got it right or not? I'll know tomorrow when I finish but the vids I saw never said anything about top dead center just for changing timing belts and just that the cam flats needed to be up which was also not quite right because the heads are approximately 30 degrees so up to me is up. IMO, should have said even with the top of the head. Anyway, during assembly the intake on my left bank was not straight up even with the tool because the tools are not precisely machined but all timing marks etc. line up perfectly and of course the chains are also on their marks. So I'm wondering if a bad phaser can cause the cam to be out of alignment visibly? If my car still has a problem after finishing it tomorrow (godforbid!!) that's my next suspect.. BTW it's amazing that you didn't totally F this engine given it was so far out of time and it is an interference engine.
@longracing25 Жыл бұрын
You were correct, there is a right and a left phaser. Put two rights or two lefts on,...wont run right or at all.
@dcounce442 жыл бұрын
I think the reason it jumped time during the 3-4 th try, it is a interference engine so if a valve hits the piston it will cause the chain to jump and or bend a valve.
@mr.biltsgarage48322 жыл бұрын
I didn't turn the engine enough to seat the chains I think they said 5 rotations Now I rotate the engine a few times by hand and then pull the fuel and spark fuses and crank it with the starter about 4 cycles to make sure it's seated before trying to start it
@lewisderful03 жыл бұрын
Love the honesty..shit happens. Having issues wit 2010 3.6 malibu..uuugh
@donlovelace2127 Жыл бұрын
Practice makes Perfect
@klyell062 жыл бұрын
I replaced my timing chains and everything else when I rotate the engine the chain wants to try and to slip around the exh cam phaser on left bank
@BuickPerformanceSupportCha160510 ай бұрын
If I had to do that job 6 times, I would throw myself off a cliff!!!! Cloyes and SA gear are the ones that don't rotate the crank to get proper timing. I'm Going to do this job on my 2010 GMC Acadia NOT looking forward to it all!!!
@bluesky2k2 жыл бұрын
I have been entertained, Thank you ! Realistic how to video for home gamers: I don't want positive reinforcement, I want to know if I should be scared to attempt this in my driveway ... And yup, this one is something... But how did it end ? Found out what was the knock ?
@natal7772 жыл бұрын
I have to give credit for trying that big job in the first place ! Hope I am wrong but that motor sounds like it has a nasty knock
@mr.biltsgarage48322 жыл бұрын
Not a knock in the block I took it apart recently It runs smooth on the bottom side and the crankshaft and bearings look good Yes I heard something to Lots of clatter at the top I'm not giving up To much effort to stop now No SURRENDER
@natal7772 жыл бұрын
@@mr.biltsgarage4832 I wish you the best for sure ! I have that same engine in my terrain
@nathanielneblett3331 Жыл бұрын
With it being an interference motor if timing is off even a little piston meets valve. Compression test to be safe. If not next video will be a motor swap.
@alien-workshop Жыл бұрын
Can you explain the third issue more? Timing to exhaust stroke. I'm having same issue but I'm figuring out how it can be backwards if the timing marks line up. Thanks
@javierperalta8243 Жыл бұрын
When you put the rtv seal do you applied to the cover or the engine?
@wildwoodtop Жыл бұрын
Cover
@jasonmassey7883 Жыл бұрын
Craziest unexplainable thing happened to me. Last week come out the store starter wouldn't work. Change the starter now my car skip time the whole bank too don't work anymore. Never heard of someone skipping timing from changing his starter
@TheMenace173 Жыл бұрын
That doesn't sound correct
@jasonmassey7883 Жыл бұрын
@@TheMenace173 what
@jasonmassey7883 Жыл бұрын
@@TheMenace173 that's what I said until changed the timing chain
@MartinMora92 Жыл бұрын
Question Guys My Intake Left Phaser actuater has some play in it, i have tried several brands including ac delco and they all have a slight play on it, is this normal?
@mr.biltsgarage4832 Жыл бұрын
From what I see tiny amount of play is normal. There are a few videos out there that show a good one and a bad one next to each other. Couldn't tell you what channel though sorry. AC Delco shouldnt have any issues if its a new one. Those are built directly to OEM specs. I've only had issues with their electronic shit, not mechanical lol. Thanks for watching!
@brandonsmith67128 ай бұрын
It might be running but it's not supposed to sound like a 4 Wheeler.
@arealmaintenanceandrepairl11038 ай бұрын
I have yet to see a video where somone wait that was wrong everyone mixes something up lol but I’ve noticed the gears are all the same it the vvt phasing that’s off a little which makes it left or right
@msgaming71601 Жыл бұрын
All I need to do, is take the cover off and clean off the old gasketmaker and re apply. The guy that did my timing chain replacement didnt use the gasket maker correctly. Still hesitant and worried to do myself. Its causing a big oil leak.
@TheMenace173 Жыл бұрын
That sucks
@Psycho_9123 жыл бұрын
The only explanation is someone messed up and put the old one back on because it wasn't worn and didn't realize the difference. Therre slight and after watching hundreds of these videos that's what I'm seeing because your right the exhaust are the same. The intake are different there made different so you can line up for timing purposes.
@rockinws65673 жыл бұрын
lol there is no relief cam. Just so you know. Do a compression test before you go any farther, you probably have some bent valves.
@mr.biltsgarage48323 жыл бұрын
I've got a lot more learning to do Thanks
@pianoguy49492 жыл бұрын
Wouldn’t timing also cause low compression?
@rockinws65672 жыл бұрын
@@pianoguy4949 Of course but you still need to check for compression once you straighten the timing out.
@Psycho_9123 жыл бұрын
But did you get it running and what were your symptoms for doing the chain obviously wrong sprocket some issues were there.
@mr.biltsgarage48322 жыл бұрын
No it's not running I think it's got a cracked head Coolant into the exhaust It's just been sitting for now
@TheMdavila8253 жыл бұрын
Torque spec for cam phasers?
@mr.biltsgarage48323 жыл бұрын
43 lb ft. 58nm
@mr.biltsgarage48323 жыл бұрын
43lbft. 58nm
@vintageking_7117 ай бұрын
What are you celebrating man that sounds like a 2 stroke dirt bike lol
@Poaf-17 ай бұрын
That’s the 3/4 cams he installed 😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂
@kimberlychowning18823 жыл бұрын
As of august the 2nd, how’s it running?
@mr.biltsgarage48323 жыл бұрын
It's not. It's got a bad head gasket or something along those trouble spot. I've only done one cylinder head job And that was on a 1981 ford escort back in the early 90s. I plan on doing that job at least twice before I get it right.
@pmscalisi3 жыл бұрын
What brand kit did you use?
@mr.biltsgarage48323 жыл бұрын
@@pmscalisi Dorman and yes I learned my lesson really fast. Cheapness has got the better of me.
@pmscalisi3 жыл бұрын
@@mr.biltsgarage4832 thanks I have a 2008 Pontiac g8 3.6v6 109K miles on it and I know this is coming. I’ve been looking at some of these full on chain sets trying to decide which one to buy. Lots of opinions out there! Would you consider the Dorman to be good quality? Been looking at Cloyes, Melling and a few others on Rock Auto. Thanks for the reply.
@mr.biltsgarage48323 жыл бұрын
@@pmscalisi I changed out the cam phasers as well. Not good quality on those parts. I'm only assuming that the chain set is the same. I did notice that GM redesigned the chain for the better. Unfortunately for those who buy Dorman get the old design. Like my self. I would not recommend Dorman brand to any one. I've purchased Dorman switches for power side mirrors and power windows and they don't act like they are quality. I'm learning the hard way because I'm cheap. If you're flipping by Dorman they are cheaper. If it's your to keep don't buy Dorman.
@Poaf-17 ай бұрын
That’s the 3/4 cams he installed. Louping
@quadscrib229 Жыл бұрын
Sheesh
@Arcade-fix Жыл бұрын
Engine sounds terrible.
@mr.biltsgarage4832 Жыл бұрын
It sure does haha. If you dont put the sound deadening back around the fuel injection, that high pressure direct injection is pretty noisy isnt it? Clickclickclickclickclick Thank you for watching!
@SimonBarsinister Жыл бұрын
If you get 5 years or more on any piece of GM junk, get rid of it.
@BB-kw8vw Жыл бұрын
My 2012 Acadia has 140k. No issues but I am a maintenance freak.
@ronjeremyjnr8 ай бұрын
I have a Traverse that is on its 2nd set of chains, it only has 155k. The owner has it dealer maintained. And it has been brought to me needing another set... awful cars.