Grease the Brake Slider pins properly and clean the bore

Рет қаралды 98,480

Жыл бұрын

Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#brakegreasing #sliderpingreasing #brakecalipersliderpins #wrong #geaseit #grease #it #howtogreasebrakecaliper

Пікірлер: 150

@KLR-650 11 ай бұрын

The drill bit trick was amazing. Also not having grease on the top of the pin. Good tips!

@RBTheMechanic 11 ай бұрын

Yup thank you bro for the feed back!!! This is a must do I had lotta car comes back with brake issues and this was it

@ivanreed-qj7uz 4 ай бұрын

Most slider pins have flats or grooves to let excess grease out....

@ashleycampbell6825 6 ай бұрын

Main reason for viewing this video was to learn how a professional mechanic cleans the bore. I was expecting something like a small bottle brush but the drill bit is SO practical. Now I should go check my brake slider pins because I am sure that I used too much anti-seize grease and particularly within the bore and the end of the slider pin.

@RBTheMechanic 6 ай бұрын

Yeah wire brush I need to get

@Zeek800 Ай бұрын

You don’t use anti seize on the calliper slide pins! It’s okay on the hub to make removing the rotor easier but silicon brake part lubricant is best and especially if you have the pins with the rubber bushing on them. Silicon won’t damage ( swell ) the rubber bushing or damage ( crack ) the rubber boot on the calliper slide pins which allows water into the slide pin bore. Grease is a petroleum product and it will “ eat up “ rubber parts.

@MidwestCombatServicesLLC 9 ай бұрын

No frills and a great tutorial. I am liking and subscribing just because you did not spend 20% of your video with ads, snake oils or fluff!

@RBTheMechanic 9 ай бұрын

Thank you

@thomasbartlett3409 Жыл бұрын

Wonderful instructions ! I have found that sliding pins and brake pads need this maintenance annually when living on dirt roads and road salt is in the mix...! From Northern Vermont here. Thanks for posting

@RBTheMechanic Жыл бұрын

Yup

@swaggerjacker1482 8 ай бұрын

Same here. In Massachusetts after winter I take off calipers and brackets, clean and relube under clips, clean and relube slide pins.

@Duke_of_Prunes 7 ай бұрын

@@swaggerjacker1482 No offense, but I wouldn't want to drive my nice car up there in the winter -- cars last me 20 years here in New Orleans.

@swaggerjacker1482 7 ай бұрын

@@Duke_of_Prunesnone taken. Growing up in Alexandria, we didn’t do it either

@JFEnterprize 7 ай бұрын

@@swaggerjacker1482I’m going for it now ohhhh 3 years after owning it 😮😢😢

@expresscontent4346 3 ай бұрын

Learn something new here. I like how you use the screw bit to remove the grease on the inside of the pin housing. Makes me want to try this out.

@RBTheMechanic 3 ай бұрын

Yup

@vossman5 9 ай бұрын

Cotton swabs work amazing to clean the slide pin chamber out. Also make sure to clean all the old grease out of the boot, I've seen many that the grease in the boot was like wax

@RBTheMechanic 9 ай бұрын

Great tip!

@newfie-dean5803 3 ай бұрын

@@RBTheMechanicGreat Q tip! 😜

@BrettHoustonTube 23 күн бұрын

Until you get cotton fibers stuck in there...

@jsoda41 4 ай бұрын

Shoot some brake cleaner in there; remove the rubber boot and let it air dry a few minutes. Then stick the blue towel in there to clean up any lingering old lube/crud in the hole. Re-lube slide pins. Use Sil-glyde- rubber safe for the boot. Clean and re-lube brakes every couple years, brakes will last a little longer and work properly.

@RBTheMechanic 4 ай бұрын

Ok thanks

@mjarzoms 3 ай бұрын

Thanks for the info, I just put in a full set of new brake pads this week and had 1/8 slider pins with much more rust than expected and not much silicone. Cleaned up with several cycles of insertion and cleaning of silicone, but plan to check out again and clean better soon with your information. Seal may actually have broken as well, will investigate a bit.

@secretariatslew Жыл бұрын

Good tips. If you are changing the slide pin boots anyways you can completely clean out that hole with break parts cleaner. The gunk will melt and pour out. Break cleaner obviously melts rubber.

@RBTheMechanic Жыл бұрын

Yup thank u for ur tips

@MrRedHotChiliMan 4 ай бұрын

Can you not pull out the boots and reinstall them if they are still in good shape?

@datatran07 11 ай бұрын

Great idea for the slide pins and cleaning when working on the brakes.

@RBTheMechanic 11 ай бұрын

Yup!!

@ronaldmagyor80 11 ай бұрын

I just spray brake cleaner with the little hose that comes with can in hole and use a long wooden q-tip to clean it out. Works everytime.

@RBTheMechanic 11 ай бұрын

Good idea!!

@grantmurray2480 2 ай бұрын

Thank your for the excellent instructions. Great video!

@RBTheMechanic 2 ай бұрын

You are welcome! Appreciate the good comment

@cesarbeg 9 ай бұрын

Excellent class, was worried about whether I had put too much or too little grease

@RBTheMechanic 9 ай бұрын

Every brake job

@RBTheMechanic 9 ай бұрын

Yup

@michaelhaynes5059 2 ай бұрын

Thanks for the instruction. Very useful and well presented.

@RBTheMechanic 2 ай бұрын

Welcome

@daveweeden8632 Жыл бұрын

The drill bit is a clever idea

@RBTheMechanic Жыл бұрын

Yup

@user-ts7gr8vq6p Жыл бұрын

Thank you very much! I did exactly like you showed, everything working great! I saved money and basically I like to do everything myself.

@RBTheMechanic Жыл бұрын

Good job I got ton of videos on brakes and every one is more details to learn lot more and do the job 100% like professional

@stevendiffy768 6 ай бұрын

Great video man! Thanks for all the tip.

@RBTheMechanic 6 ай бұрын

Welcome

@swavekbu4959 2 ай бұрын

Fantastic teacher, thank you VERY much!

@RBTheMechanic 2 ай бұрын

Yup thank you!!

@atticusrussell1225 11 ай бұрын

great video. Thanks for the tip about the drill bit

@RBTheMechanic 11 ай бұрын

Yup little but time doing this will work out well

@anonymousperson4363 6 ай бұрын

Best source I trust.

@RBTheMechanic 6 ай бұрын

Yup me too

@stormcrowe9820 6 ай бұрын

Great video explanation!

@RBTheMechanic 6 ай бұрын

Yup thank you

@zingo2664 3 ай бұрын

great video, very good idea using drill bit ! ,thank you for posting 😁 10/10

@RBTheMechanic 3 ай бұрын

You bet!

@jerryweigl4730 10 ай бұрын

I think the video is generally good, but I didn't see anything about making sure the ends of the little rubber boots go in or around the pins and the caliper. You can't just push the stuff together and expect the boots to slip in place. If the boots are on correctly, there is no water or dirt that will get onto the pin and cause rusting, etc.

@RBTheMechanic 10 ай бұрын

Yeah need the boot on

@homuraakemi9556 9 ай бұрын

He says this at 6:03

@jaimecabrales8514 10 ай бұрын

Thank you for sharing.

@RBTheMechanic 10 ай бұрын

My pleasure!

@HerbertAtkinson 9 ай бұрын

I just replaced a plastic bushing that goes around on a sliding pin on Toyota Camry I had to take off the caliper frame removed the rubber boot to get into the hole to remove the remaining worn plastic bushing & replace with new one which auto zone sells the kit for these way cheaper then dealership that wants 15$ just for one bushing which part store was only 6$ for extra parts.

@bobm9509 Ай бұрын

I'm starting to believe the grease does more harm than good. I've never had more problems with uneven pad wear since i learned to 'properly grease' the pins.

@RBTheMechanic Ай бұрын

Too much grease on pin will cause issues I did video just on that

@bobm9509 Ай бұрын

@@RBTheMechanic I used less than you did, not even a year ago, and here i am with another pair of rotors wasted on one side. I'm sitting here now, debating to try them dry.

@musicfashionstyle9269 9 ай бұрын

Teach very well.

@RBTheMechanic 9 ай бұрын

Thank you

@deedle6073 10 ай бұрын

A gun cleaning rod with brush cleans the bore out good.

@RBTheMechanic 10 ай бұрын

Yup great idea

@johnjones4453 4 ай бұрын

Thank you !!

@RBTheMechanic 4 ай бұрын

You're welcome!

@andridabel Жыл бұрын

thanks information👍, im from indonesia 🙏

@RBTheMechanic Жыл бұрын

Welcome!!

@TheAriiiiii 3 ай бұрын

Thanks for the video, question about the slider pin that you didn't remove from the calliper, why? And do you not need to screw that slider with the rubber grommet in?

@RBTheMechanic 3 ай бұрын

No what u mean y I think I did

@thepiecesfit5049 3 ай бұрын

I like to remove the rubber boots, clean the inside. They will have old dried up lubricant in there too. Then hit the chamber with some brake cleaner. Roll a shop towel into the size of the chamber (cigarette) and twist it inside till I get it clean and all the old grease out.

@RBTheMechanic 3 ай бұрын

Yeah do so!!

@abemohsin4469 7 ай бұрын

I just had my rear end brakes and rotors done, but one side I had an issue with the longer slider pin not compressing after greasing it and cleaning the caliber whole, it was a big gap, I eventually replaced the longer sliding pin with the smaller sliding pin and it worked just fine, now the issue I'm having now is when I brake, my car makes clunking loud noise. Could the removal of the longer sliding pin be the issue since it was replaced by the same smaller pin as the one on the bottom?

@RBTheMechanic 7 ай бұрын

Not sure I would check all the bolts and double check my work

@adamsjay212 Ай бұрын

Its like cleaning your ears from built up ear wax but just for vehicles.

@RBTheMechanic Ай бұрын

Nice example exactly like it

@junzilla13 11 ай бұрын

What are your thoughts about using the black brake grease for the slide pins? The Amazon reviews say no but the description says safe on rubber

@RBTheMechanic 11 ай бұрын

I have used it didn’t have issues but silicon works good for me

@homuraakemi9556 9 ай бұрын

I used CRC stuff and it swelled the rubber like crazy. Avoid anything that's not silicone grease.

@vossman5 9 ай бұрын

@homuraakemi9556 I've ended up just removing the rubber sleeves many times due to them being swollen, they aren't necessary, just used as another anti rattle piece.

@homuraakemi9556 9 ай бұрын

@@vossman5Going to do my front brakes today or tomorrow. Considering doing the same.

@jasonpierce1980 3 ай бұрын

Does that rubber sleeve on the slide pin always go on top? Working on 2003 Saturn Vue.

@RBTheMechanic 3 ай бұрын

Usully u gotta check to see where it came from not alway is on top

@jasonpierce1980 3 ай бұрын

@@RBTheMechanic not worried about what I did I'm worried about what the person did before me. I lined all the parts straight in front of me and did them one at a time. Can't get much information about this on the internet.

@sheerwillsurvival2064 Жыл бұрын

👍🏻

@godzilla_son4383 9 ай бұрын

Hi there I have a 2020 Altima just did a brake pad job on it and still squeak, though I had a defective set of pads so I replaced it again and still squeak. I replace all the shims bracket but noting helps, rotors looks good I even used the quite stuff on back of the brake pads still squeak?

@RBTheMechanic 9 ай бұрын

What brand ur using brake pads and rotors if there are wagnersbur gonna need some ear plugs cuz they Squak like train

@godzilla_son4383 9 ай бұрын

@@RBTheMechanic Bosch and power stop

@RBTheMechanic 9 ай бұрын

@@godzilla_son4383 no bad well check ur work maybe hardware is scraping against the rotor

@seragali1353 7 ай бұрын

I always have this problem. I lubricate the pins and after a short while I find them stuck and not moving... So what is the solution and what is your advice? Note: Silicone grease is not available in my country, so what is a good alternative?

@RBTheMechanic 7 ай бұрын

Clean and liber light amount and make sure broke is clean

@musicalokaoficial 6 ай бұрын

Hey captain I saw another video somewhere else that is not recommended to use silicone. The reason why I’m asking is cuz I want to do mines pretty soon because I’m 100% these mechanics haven’t grease my calipers pins properly and I would like to do them. Any suggestions I will appreciate it.

@RBTheMechanic 6 ай бұрын

I like the greasing I use make sure u clean old grease out inside the bore also here a video tips on greasing kzfaq.info/get/bejne/qbGid5uD1Ne2oZ8.htmlsi=oWwJ--yIwUKjOhv_

@musicalokaoficial 6 ай бұрын

@@RBTheMechanic thank you I already had watched the video too. 👀😀. Thanks for all the great videos you do mi amigo great help!!

@RBTheMechanic 6 ай бұрын

@@musicalokaoficial cool ur ahead of the game!! Good luck update me how it goes

@israel9294 4 ай бұрын

I used caliper grease from AutoZone on the pins, months later I checked the pins and they were stock on tight the grease turned into hard clay. I don’t know why that happened and know I don’t know if I should replace the caliper.

@RBTheMechanic 4 ай бұрын

Clean it out well and use silicon grease

@Grrrnthumb Ай бұрын

Which one from Autozone did you use?

@israel9294 Ай бұрын

I used CRC synthetic

@newfie-dean5803 3 ай бұрын

I recently changed the front brakes on my 2019 ford escape but I did not clean out those bores. I cleaned up the bracket and the pins and greased those but since doing the brakes sometimes I hear scraping as I come to a stop but only when almost stopped. And my gas mileage has decreased. Do you think failure to clean out the bores is my issue causing the pads to not release? I had replaced the rotors and the pads. I’m not sure why it scrapes. What would cause the scraping? It seems to sometimes go away and then it comes back. I hear no scraping when driving.

@RBTheMechanic 3 ай бұрын

I would go back and re due it also make sure brake are free in bracket

@newfie-dean5803 3 ай бұрын

@@RBTheMechanic yes, that’s the plan. I’m not too enthused about taking it all apart again! I took my time doing it so I did not think I would have any problems.

@newfie-dean5803 3 ай бұрын

@@RBTheMechanic I cleaned the caliper bores really good and greased it good and my I problem is solved! That was my issue. I went from 19 mpg mainly city to 24 mpg since doing that so it was really killing my gas mileage! One pin does not slide as loose in the driver side caliper as the other one but it’s moving ok and both pins in the passenger side caliper move loose. Not sure why the one pin was a bit stiffer. Maybe the heat messed up the plastic insert in the caliper as it is clean and I can’t think of what else could cause that. I did receive new inserts with my new pads and I considered to remove the old insert but I was concerned that maybe it’s not a perfect fit and then I have to replace the caliper if I mess it up. Do you think the one pin being not as loose will be ok? As mentioned, the gas mileage is significantly improved and there is no scraping and the wheel was feeling hot after being driven in the city for a while before, but now each wheel feels only slightly warm to the touch and the back wheels feel cold to the touch. I think that is normal considering the front has so much weight.

@RBTheMechanic 3 ай бұрын

@@newfie-dean5803 not sure I would check to see if they are moving freely

@1marcelfilms 9 ай бұрын

You dont really need the rubber bushing if its swollen you remove it there is only a small chance of rattle

@RBTheMechanic 9 ай бұрын

Yeah true

@x-lue1066 Жыл бұрын

People will think why you’re using a drill, it might damage the rubber pieces

@RBTheMechanic Жыл бұрын

There is none rubber inside

@howtodoitdude1662 4 ай бұрын

If you have rust inside, the bore, you’ll need the wire brush

@RBTheMechanic 4 ай бұрын

Yes

@davidjohnson2185 5 ай бұрын

The one with the rubber on does it go on the top or bottom

@RBTheMechanic 5 ай бұрын

Here’s I made a video on that kzfaq.info/get/bejne/n7hyiaV0rqe7pmQ.htmlsi=gMOLWE9WEFnd_IQ8

@davidjohnson2185 5 ай бұрын

On a Mazda 2009

@davidjohnson2185 5 ай бұрын

Thanks bud

@RBTheMechanic 5 ай бұрын

@@davidjohnson2185 welcome

@RBTheMechanic 5 ай бұрын

@@davidjohnson2185 follow how u disassemble it other wise if u lost the track might need diagram from dealer because they choose where to put

@cesarbeg 9 ай бұрын

How often this must be done?

@joehawthorn3018 8 ай бұрын

yearly, I clean out when I change summer tires to winter. So that s 1 time each year in Ontario, CANADA

@seragali1353 7 ай бұрын

Can it be replaced with joint grease?

@RBTheMechanic 7 ай бұрын

Yes

@bobtakealook6420 Жыл бұрын

I hide extra grease with a putty knife in the caliper

@MrRedHotChiliMan 4 ай бұрын

Do you have to remove the caliper to clean the slide pins?

@RBTheMechanic 4 ай бұрын

Yes

@MrRedHotChiliMan 4 ай бұрын

@@RBTheMechanic thanks for your reply. Is it necessary to compress the piston as well?

@RBTheMechanic 4 ай бұрын

@@MrRedHotChiliMan ur gonna have to it will not go back in easy so if ur luck u can manage it without compressor other wise push it back slightly

@MrRedHotChiliMan 4 ай бұрын

@@RBTheMechanic right on, thank you! Much appreciated!

@dannynica7480 Жыл бұрын

Are you sure you are not doing it wrong?? In my honda the Rubber bushing on the pin goes on the bottom, not the top

@RBTheMechanic Жыл бұрын

I noticed and did video on many many cars video is coming up soon the rubber goes on top but I don’t see it doing any harm in bottom but mostly seen it on top

@allentig Жыл бұрын

Any grease is ok? Drill bits? Bad advice

@RBTheMechanic Жыл бұрын

Just to clean it out u can use bit since it has the mechanics to chew up and pull out the grease. And no not any grease watch my greasing vide use slider pin grease most companies that make calipers use silicon base slider pin grease

@nbowling10trio 4 ай бұрын

Good idea bro. Nice way to use your noggin😂

@RBTheMechanic 4 ай бұрын

Thanks 😅

@sehpengpng7631 Жыл бұрын

Maybe i'm doing wrong , because i'm already put the grease on the tips of the pin.....and get the wheel stuck

@RBTheMechanic Жыл бұрын

Yeah I would avoid it

@carroll6 Жыл бұрын

man- that stuff is expensive.

@RBTheMechanic Жыл бұрын

Yeah

@hailuu7062 Жыл бұрын

Hello master brother

@RBTheMechanic Жыл бұрын

Hello there

@z33thr33 Жыл бұрын

There's not that many "p"s in "properly"

@RBTheMechanic Жыл бұрын

Yeah the auto txt did it I can’t go back change it but I guess it’s gonna be PPLY

@ivanreed-qj7uz 4 ай бұрын

Well you spent 'properly' wrong !...Not a good start !

@RBTheMechanic 4 ай бұрын

@cranercrew9836 3 ай бұрын

@ivanreed-qj7uz You probably shouldn’t worry about the spelling of others if you can’t spell ‘spelled’

@Grrrnthumb Ай бұрын

Haha, yeah I thought this was hilarious, that the spelling police can't spell spelled.

@VEDATOR_official 4 ай бұрын

A couple of my pins wouldnt go back in all the way. Next time I do pads ill try doing this first

@RBTheMechanic 4 ай бұрын

Yes this is a must clear out the slerance

@VEDATOR_official 4 ай бұрын

@@RBTheMechanic no matter how much I clean everything, even with 0 grease, the pin didnt want to go in all the way. The rubber bushing was the problem. I cut a small channel off of the rubber bushing o ring and it worked