10 Minute Cam Swap!

No video

10 Minute Cam Swap!

Рет қаралды 923,972

Күн бұрын

can you bore a 5.3 into a 6.0?
• CAN YOU BORE A 4.8 / 5...
only what you NEED to know!
• The BEST LS Cam Swap V...
Amazon now has a budget valve spring compressor!
amzn.to/2yjyw3r
Special LS Style Harmonic Balancer Puller
amzn.to/2H2w1Es
Amazon Also sells LS3 valve springs good for .560 lift! perfect for your mild budget cam swap!
amzn.to/2Y8cBnm
LS3 Chevy SS Sedan cam swap.
• LS CAM SWAP
follow on Instagram www.instagram....
🎶 🎶 🎶 🎶
Music: After All
Artist: Sovereign Sound
Music: Run
Artist: Sovereign Sound
Link To Artist Below
open.spotify.c...

Пікірлер: 1 100

@BoBuilds 4 жыл бұрын

Amazon now has a budget valve spring compressor! amzn.to/2yjyw3r Special LS Style Harmonic Balancer Puller amzn.to/2H2w1Es Amazon Also sells LS3 valve springs good for .560 lift! perfect for your mild budget cam swap! amzn.to/2Y8cBnm

@drmachinewerke1 3 жыл бұрын

Where is your shop. And how much down time with tune etc.

@FCD-dl7bk 3 жыл бұрын

Does this swap apply for a 6.2 cam swap in a Denali also.......thanks in advance for your reply and thank you for the awesome video with tools needed and specs.

@ss0073 3 жыл бұрын

@@FCD-dl7bk Yes

@twistedarrow3574 3 жыл бұрын

Takes 10 min an charge 500$ lol

@chevy4life01 3 жыл бұрын

What cam did u put in??

@chrismayes2149 3 жыл бұрын

Finally, a guy that is focused on the job and not talking throughout the whole video. This is honestly the most straight to the point no nonsense video I've found. It's also helpful to me because I want to find one an old 4.3 silverado.

@originalg6918 3 жыл бұрын

Why cam a 4.3 lol just swap it with a v8

@chrismayes2149 3 жыл бұрын

Because some people like going with the oddball engine and going against the grain instead of doing what everyone else does.

@BoBuilds 3 жыл бұрын

It's not a 4.3? Its a 4.8 V8

@jasonensley1601 3 жыл бұрын

couldnt agree more, didnt have to hear how great he thinks he is how many burnouts hes done, he fidnt show an entire photo album of himself skydiving swimming with the dolphins or advertising his daughterd girlscout sales,"granted id most likely have bought some boxes of cookies, but ya, this was one of the best tutorials ive seen.

@jasonensley1601 3 жыл бұрын

@@originalg6918 i thought it was a 4.8 v8 im pretty sure it was i could b wrong tho

@veritasvincit4178 3 жыл бұрын

10 min of professional on video= me taking two days as I refer back to this video and others on KZfaq

@chefzackkasmar6767 2 жыл бұрын

100% on point!! Lol

@tyronetripod8536 2 жыл бұрын

yeah more likely even took him a couple hours

@BoBuilds 2 жыл бұрын

Yeah its a 3 hour job if everything goes smooth. I just meant cam swap done in a 10 minute video lol

@chefzackkasmar6767 2 жыл бұрын

@@BoBuilds Great Job Man. My comment meant that When I do my Cam swap I will reference your Videos non stop, playing and pausing over and over. Thanks for taking the time to share! I am sure you have helped more than just me with this vid! At least 40 of the views on this video are from me watching it to psych myself up to have the balls to do my own swap! It worked, Im going for it! 💪💪🍻Cheers.

@jjano2320 2 жыл бұрын

It takes me 10 min. to find the right tools.

@rjack151 2 жыл бұрын

I like how homie is just over here busting out a task, and tweedle dee and tweedle fuck are in the background fiddle fucking around.

@Ka_Gg 3 жыл бұрын

Awesome video! Straight to the point. You didn't talk about some stupid story for 5 minutes about how you needed more power. You didn't spend 2 minutes struggling to find the right socket for this and that. We don't need to see you remove every single rocker arm bolt. You kept it simple. The world needs more videos like this.

@DavidToyotaHead13 Жыл бұрын

The OG KZfaq videos with minimal editing. Subbed!

@Ka_Gg Жыл бұрын

@@DavidToyotaHead13 yep. Back when videos were to the point. Now it's about being a "content creator" and being entertaining.

@LJimenez0185 4 жыл бұрын

Finally a complete guide, I’ve watch different videos on how to do a Cam swap but this one is the best, simple and pointing the right angle on the video, great video, thanks for sharing!!!

@BoBuilds 4 жыл бұрын

Thank you!

@justingriffith2991 3 жыл бұрын

@@BoBuilds wa t kind cam. In it

@jacobnicoletti1235 3 жыл бұрын

I always thought you would have to remove basically the whole top end so you could get to the lifters. But then you used that wooden dowel. Didn’t even know that trick existed. Good work brother, you taught me a few things today.

@BoBuilds 3 жыл бұрын

That's what it's all about! Glad this video helped you!

@doctorboylerdemexicali8905 3 жыл бұрын

How many extra horses did it gain with the swap?

@SuperchiefApache 3 жыл бұрын

Yeah, I thought that was just freaking awesome!!!

@SuperchiefApache 3 жыл бұрын

@@doctorboylerdemexicali8905 Man, I have not a clue, but it sounded NASTY!!!!

@doctorboylerdemexicali8905 3 жыл бұрын

@@SuperchiefApache awesome

@kirkmcknight113 3 жыл бұрын

I am thoroughly impressed with the work you did. I'm 70 yrs. old and don't know if I would try that, but your video would be my go to on how to get it done. This was an awesome video and made a big deal seem like changing a set of plugs. Y'all do good work!!! Kirk n TX.

@gtcp85 3 жыл бұрын

Finally... A tech that is not afraid to get his hands into the job. Seen guys go through what seems like a box of gloves a day when the shop pays for them. Oh yeah.. Content is great too.. Thanks

@SuperchiefApache 3 жыл бұрын

Super good, straight forward, no stupid stuff in between!

@skeetermcswagger0U812 3 жыл бұрын

The best Cam swamp video for an LS motor I've ever seen in my entire life!!!!!!!

@BoBuilds 3 жыл бұрын

Thanks a lot man! I tried to be straight to the point and no Bull shi%

@skeetermcswagger0U812 3 жыл бұрын

@@BoBuilds You have successfully managed to do just that!!!👍

@vincebermudez869 4 жыл бұрын

This is hands down the best cam swap video on the internet as of yet. You guys give the average Joe the confidence to take on this project and complete it from start to finish with all the details thrown in. Thank you for taking the time to show us shade trees hows it done properly and effectively. Liked and subscribed. 👍

@coarsegrind 4 жыл бұрын

Instead of pulling the top hose off the pump, pull it off the radiator. Then use a shop vacuum to pull the remaining antifreeze out of the block. No Mess!

@YungJackie22 3 жыл бұрын

Came here to see a cam swap but I heard east 1999 aswell, my day has been made

@sxs4l245 3 жыл бұрын

Best no bull spit video I have seen yet! 5 stars and 2 thumbs up.

@reed_shaw1816 2 жыл бұрын

Thank you sir for actually working/showing and not talking

@donellis5005 3 жыл бұрын

I get the feeling he's done this a couple of dozen times

@Usmc913 3 жыл бұрын

You have made my cam swap so much easier. Thank you. People make it sound so much more difficult than it is.

@tanneralexander5886 2 жыл бұрын

Does the truck need to be tuned after cam and headers

@Usmc913 2 жыл бұрын

@@tanneralexander5886 yes you do

@savagesock3598 Жыл бұрын

@@Usmc913 what's do you need to do to it? Pcm reprogram?

@shedred1967 3 жыл бұрын

Stock is good, an aftermarket cam for your specific needs is just great. That sounded soooo much better.

@brandonbressman8577 5 ай бұрын

That video was perfect and simple. I hope you find an extra 10mm or two! Thanks!

@leatherman1934 3 жыл бұрын

Idk about 10 minutes, but cool swap! Sounds sweet!

@BoBuilds 3 жыл бұрын

Just meant the video is 10 minutes lol but thanks!

@BCooper89 3 жыл бұрын

@@BoBuilds what cam and lifters did you install? And did you have to have it tuned?

@chrisjeanotte9879 3 жыл бұрын

Cam?? And did it need to be tuned

@carlosbermudez4444 3 жыл бұрын

I bite click, lol and I bit

@Kingbuzz92 3 жыл бұрын

Of course any cam needs to be tuned

@migicman02 3 жыл бұрын

Only a real professional would share torque specs at the end of the video, big fan!

@tedwarne8236 2 жыл бұрын

They do make books for that

@rupertburrows9767 3 жыл бұрын

Wow this is definitely one of the best instructional videos i've watched. Thanks!

@BoBuilds 3 жыл бұрын

Thank you!

@theredfive 2 жыл бұрын

this is the best step by step cam swap video without all the bullshit commentating, straight to the point , very informative. keep up with the great videos, thanks for the info . will be doin swap asap

@TexasGTO 5 ай бұрын

Learned a new trick to remove fan clutches. Thanks!

@King87brougham51 4 жыл бұрын

A true complete guide to ls cam and valve springs swap👍🏿👍🏿👍🏿👍🏿💪🏿💪🏿💪🏿💪🏿👌🏿👌🏿👌🏿👌🏿💯💯💯💯🔥🔥🔥video

@BoBuilds 4 жыл бұрын

Thank you man, glad you liked the vid! Hope it helps!

@King87brougham51 4 жыл бұрын

Man I love this video it helped me do my first cam swap thanks

@BBB-ly8ro 3 жыл бұрын

Total pro video and work. I have to mention to other viewers, if your working outside and a wind blew all those pecan leaves down on the your project it would have been a preventable disaster. I’m so glad I don’t have to take my cam out at this time. Good luck all. Great video.

@jessewalz 9 ай бұрын

Most well done tutorial on KZfaq period!

@erickuribe9860 3 жыл бұрын

Thanks for the torque specs👍

@ishotjustin 4 жыл бұрын

Absolutely the best step by step video! Had everything I needed to know and good audio for end result. Thank you for making a straight to the point video!!

@BoBuilds 4 жыл бұрын

Thank you so much for this comment!

@ishotjustin 4 жыл бұрын

GreaseMonkeyMods well thank you so much for such a useful video!

@josephstalin9500 2 жыл бұрын

This video gives me the confidence I needed to do it at home. I'll be back in a couple months once I have everything ready for an install

@loafoftrees7046 2 жыл бұрын

Best of luck

@raymondcbaker30 Жыл бұрын

I was literally giggling at the sound of that cam... it sounds so sick!

@nickboucher7339 3 жыл бұрын

Great title dude!... Nice editing. I thought you were going to hole saw the grill, AC condenser, trans cooler, and radiator to put that cam in, in ten minutes......

@rb1602 3 жыл бұрын

Love the vid. No bullsh!t intros. All business.

@narule2695 3 жыл бұрын

I wish all videos were like this

@ccale03 2 жыл бұрын

I know way late to the game, and only watched 2 of your videos so far but definitely it sure why you don’t have more followers. Best how to I’ve seen on KZfaq, love that you put torque specs at the end. 👍👍

@BoBuilds 2 жыл бұрын

Thanks man that means a lot

@micahmallett2989 3 жыл бұрын

I usually don't comment but this video was perfect! Step by step captions with music are nice. No talking. No bs. Thanks for throwing in the torque specs at the end. Keep it up! 🤘

@juanlanda2441 Жыл бұрын

It left me with lots of questions.

@MadballBaby 3 жыл бұрын

Love tha sound of that lope ,want a cam in my 5.7 Tahoe,Maryland showing ❤️

@SuperchiefApache 3 жыл бұрын

Go Maryland....what part? I’m northern Fredrick County!

@MadballBaby 3 жыл бұрын

@@SuperchiefApache /Prince George’s county,ayeyyyy

@SuperchiefApache 3 жыл бұрын

@@MadballBaby Ha! My old stomping grounds! I went to Northwestern Sr High in Adelphi, and lived in Lanham, Hyattsville, Beltsville, East Pines, and Bladensburg area! PG county enough? Lol!

@radomark408 3 жыл бұрын

Nice! Made that look super easy with all the right tools! If you were closer would love to take my truck to yall! Well done

@cargotoolshop5319 3 жыл бұрын

Expect the cam swap to take the better part of a day not just ten minutes

@radomark408 3 жыл бұрын

@@cargotoolshop5319 well obviously..

@JordanKline 10 ай бұрын

I have never found a more helpful to the point video.

@mrorganic13 5 ай бұрын

Sometimes I’m thankful for a my lil 4 cylinder Honda

@mrhookups 4 жыл бұрын

BEST HOW TO VIDEO!! EVEN MY MOM CAN SWAP A CAM WITH THIS VIDEO!💯👍

@BoBuilds 4 жыл бұрын

Thank you!

@mrhookups 4 жыл бұрын

GreaseMonkeyMods Question....What’s the Specs on that Cam You Installed?

@davidshull8929 3 жыл бұрын

Great summary! I wish it was this easy for removing DOD. :-)

@eddieroberts6242 2 жыл бұрын

Like most, I'm very picky about who I trust to work on my 2007 Tahoe LTZ. After watching this excellent video, I'd let you get your hands on my girl any time. Meticulous and exact work demonstrated. You da man.

@zincyellowmach1523 2 жыл бұрын

Good straight and to the point video. I would caution everyone that the crank pulley is a one time use unless you drill and key it. Just installing the old one can result in a spun crankshaft pulley. That's muy mal

@mygtr2021 3 жыл бұрын

That was very relaxing.. good job dude.

@BoBuilds 3 жыл бұрын

Thank you!

@Stingyduce 3 жыл бұрын

Man I sold my 04 Tahoe the cam was bad on a lobe causing mis fire was told it would be 2500to3k to do the job wish I knew this stuff . Great video bro!!!

@cargotoolshop5319 3 жыл бұрын

They told my parents $7500 and $500 later in my shop we had the afm/did delete done with new gaskets and bolts and new cam and lifters, new exhaust studs and oil pump o ring fix, stay strong and smart

@billyd0468 3 жыл бұрын

If you already lost a cam lobe, the metal has already went through the engine. Any repair will most likely be short term. The damage has been done. Band Aid repairs will destroy a shops reputation. The shop needed to explain this along with their quote.

@ramondhunter8191 Жыл бұрын

Best video on a cam swap I have seen on YT

@shickenchits8123 3 жыл бұрын

Step 1, Clean your engine first. You don't want to take the chance of letting Any dirt in.

@TheTexican05 2 жыл бұрын

This. I’m amazed how many techs don’t do proper engine bay prep prior to internal work. Takes very little time compared to dirt and debris falling down into the motor. Valve cover removal alone will allow dirt from hoses and harnesses above to just float right down into the heads and oil areas.

@cruisingthethaiway6881 2 жыл бұрын

Very dirty unprofessional work. That would not be tolerated in my shop. He would either learn very quickly how to to correctly or be fired.

@zachariahmagallan5738 Жыл бұрын

I see your pissed he is helping people save money

@shickenchits8123 Жыл бұрын

@@zachariahmagallan5738Go away troll

@JORGE4757S Жыл бұрын

@@cruisingthethaiway6881 KZfaq videos and profesional don't go in the same sentence Don't look for that here

@whowho7969 3 жыл бұрын

Best cam swap video 👍 thank you

@MADMIKE74 24 күн бұрын

Shouldn't tighten down the timing cover bolts until the crank pulley is fully seated on and into the crank seal. That is the alignment tool for the timing cover. Torque afterwards.

@hasve978 3 жыл бұрын

I have to say if you can do that in 10 minutes I want you as my mechanic.

@clarksgarageofbadhabits6803 3 жыл бұрын

Can’t forget about getting it retuned tho👀👀👀

@Nakira2000 2 жыл бұрын

Oh no, I was afraid of this. Thank you for the video its very helpful. This will be one project I cannot do physically., but gives me an understanding of what needs to be done

@sethmccartney6844 2 жыл бұрын

I like how the tailgate sticker said Humphries Jena la that’s where I’m from small world we live in

@chriseller757 7 ай бұрын

I cant believe he didn’t put new lifters in. Your right there. Whats a couple hundred more vs all that labor to change them later. This is a clear example of the difference between a technician and a parts changer.

@BoBuilds 7 ай бұрын

The technician doesn’t dictate what the customer can afford, I can recommend everything but can only do what is afforded. Being my father I explained the risk and he understands the risk of not replacing other parts. Truck has been about 20k miles on this cam swap with no hiccups

@james10739 3 жыл бұрын

I was confused about the changing springs 2 cylinders at a time but I see without using air just having the piston keep the valves from falling

@cargotoolshop5319 3 жыл бұрын

That is correct, I like the air method better but the piston trick is fail proof

@1975ssnova 3 жыл бұрын

Thanks for the video! I’m doing a BTR stage 1 cam in a couple weeks. Along with the Diablosports i3 intune platinum tuner to compliment it. Then will get the Lew from Diablo to hook me up with a custom tune for me.

@amax4409 14 күн бұрын

No BS straight to the point appreciate it 👍🏾👍🏾

@brandonbennett1564 3 жыл бұрын

Awesome work man!thanks for showing this.

@shanefoster2367 4 жыл бұрын

Thanks, I plan on doing this to my 5.3 HO

@PaulysAuto Жыл бұрын

My guy you are so talented...uninterrupted too 😂 Brilliant job of making this video, you did a great job of filming here!

@fredstone3875 3 жыл бұрын

Finally a how to video for grown UPS with some Common sense excellent editing thank you.

@mr.Bowtie40 3 жыл бұрын

I like the sound of that I have a 06 chevy avalanche trying to put some extra peep to it

@mr.Bowtie40 3 жыл бұрын

I will look into it ty george

@1975ssnova 3 жыл бұрын

I’m going to be installing a bar stage one in my 04 Silverado 1500 within the next couple weeks. I just got a diablosport intune i3 platinum and was messing with it yesterday and today. I highly recommend you check it out also. You can pretty much make a custom tune yourself if you know what you are doing! Also if you buy it from doable lew you get a custom tune just for your truck.

@westcoast2797 4 жыл бұрын

A Pro tip for the future ..clean all derby before working on an engine shop vac or blow some air around the area your going to work in. Keep up the work otherwise.

@rodrogers6895 2 жыл бұрын

Derby? Debris maybe?

@3pilot 2 жыл бұрын

Derby, KS could use a clean. But I don’t know what the city has to do with this.

@drewmurray2583 Жыл бұрын

So I just used the dowel rod trick on a 2007 4.8 but not the way you are thinking. I had to put the engine on a stand and turn it upside down so I could remove the oil pan, windage tray and poke the lifters out of the way enough for the cam to come out. PITA the lobes do not go as far out as the journals on that stock 4.8 cam so there is no way to raise the lifters enough.

@datzee3458 3 жыл бұрын

Now can you make a video on the setup you use for tuning? I think that will really help everybody out.

@jwpranzo 3 жыл бұрын

Great vid with lots of gear tips, especially using wooden dowels to hold the lifters up instead of removing the intake and taking out the lifters. But reusing the old timing gear/chain set? Why not replace them since you have it open already?

@cerberous741 3 жыл бұрын

You can't do that on this engine. This not a 350. This is a 5.3 that is ls based. You have to remove the heads to get to the lifters. I do agree that he should have changed out the timing chain but it requires removal of the oil pump which requires the oil pan to be dropped.

@iamtheoffenderofall 2 жыл бұрын

Entire job is shade tree mechanic work.

@stephenwhite5444 2 жыл бұрын

@@iamtheoffenderofall I'm sure someone who knows just enough to think they know, would think so. Nothing shade tree about it. Its excellent work.

@acehealy6102 3 жыл бұрын

so is there a 4l60 swap video after this cam one? haha

@sbranham86 Жыл бұрын

You can do it in 2 steps. Step 1: drop it off step 2: pick it up. Nice video bud, makes it look simple

@Large_Sarge Жыл бұрын

A god amongst men. Thanks for the amazing guide.

@MrLocz209 3 жыл бұрын

Two days later! The timing chain goes out!!!!! Repeat 1/2 job again!!!!!

@BoBuilds 3 жыл бұрын

Well it's been about a year now, sometimes you gonna send it

@MrLocz209 3 жыл бұрын

@@BoBuilds nice job! But why didn’t the chain get replaced? A few years ago I had my Transmittion rebuilt and the mechanic didn’t ask me if I wanted to replace the main seal and NOW I have to put a Quart of oil once a week and it’s frustrating and expensive! I wish he would’ve called or said something about it!

@joshfrank1680 3 жыл бұрын

@@MrLocz209 The question is why didn't your mechanic just replace the seal? That's a no brainer on a job like that.

@1975ssnova 3 жыл бұрын

It’s not a common thing with these engines! The chains and gears pretty much are not a issue.

@fbrtube 3 жыл бұрын

Hey great video, I’m about to swap just about everything mentioned at 150k miles... I have a few questions just double checking here. 1: which way did you rotate cam sprocket when you were doing 45* turns? 2. Would you follow the same turning process on valve springs if you’re replacing lifters as well? Or just pull the whole cylinder? 3. Did you mean to say torque valve cover bolts to 106 lb in or 106 lb ft? Thanks for the great video - really awesome stuff.

@blueridermg 3 жыл бұрын

Something I had in mind as well. If you look at the marks he made with his fingers on sprocket you can tell which way he turned it. Hope this helps

@SuperEastcoast 3 жыл бұрын

To the point video!! Thank you for the professional work and easy to follow video.

@james10739 3 жыл бұрын

The last minute was just clips of it running and stuff that's a 9 min cam swap

@mydogma7116 2 жыл бұрын

After watching this I know why my mechanic charges lots, lol.. great video

@cristiangarciamoreno1001 2 жыл бұрын

Yoooo what a guy, impressive!! Haven’t seen a video like this in a very long time

@arlenecarrisalez8300 3 жыл бұрын

what part of texas are you at and what do you charge to do this on a 2011 chevy silverado with a 5.3

@ls4.8frank 4 жыл бұрын

I wish someone could tell me how to properly bleed air out of the cooling system on a 2011 Silverado 4.8L.

@BoBuilds 4 жыл бұрын

You need this kit amzn.to/33VsXnv Attach to reservoir, fill with coolant and let engine run at operating temp. Give engine some revs and let run until no bubbles are visible in the funnel

@ls4.8frank 4 жыл бұрын

@@BoBuilds thanks brother. 👍

@jose72arvizu94 3 жыл бұрын

Always turn on heater full blast begin to fill. Full then burp thru bleed

@richardvermillion2784 3 жыл бұрын

Airlift is your friend! Or fill upper rad hose first.

@kuwaitiazrg 3 жыл бұрын

Bleeding air out of cooling system

@joedavis4389 2 жыл бұрын

10 minute cam swap, now that's some funny shit!! I watched it anyway knowing that way BS!! Good job!!

@routtookc8064 3 жыл бұрын

Step 9: Remove transmission.... WTF.....oh "lines" blended in with the alternator...

@BoBuilds 3 жыл бұрын

Lmao

@FARTNREDNECK 2 жыл бұрын

should have been step 1: remove the garbage 4l60

@MrJAV418 3 жыл бұрын

what cam is this?

@josemaldonado8157 2 жыл бұрын

Excellent video only issue I have why go to all that trouble changing the cam and not installing a new timing chain and cam and crank gears I'm just saying everyone has a reason.

@sergeantseven4240 5 ай бұрын

Need something like this for the VVT guys. Its nice to be able to keep that wide torque range but there isn't a ton of info on here about a VVT cam swap.

@OMGITSAAAJ 3 жыл бұрын

This video gets an A grade from me! (Would’ve been an A+ if you had thrown in the tiniest eensey weensey REDLINE REV!

@louiscardenas6637 4 жыл бұрын

So I'm thinking of doin my 5.3. My question is the front cover, how do you make sure it's perfectly centered over the crank? Do you use the centering tool I've seen on the net? Also, is there a front main seal on the crank pulley? I need to do my rear main seal and seen vids where they use a tool to align the rear plate and get it centered. That's why I ask about the front. I've never done a cam swap but the more vids I watch,its boosting the confidence!💪 Thanks!

@johnsimun6533 3 жыл бұрын

LS or Vortex? I have the LS4, and along with this, need the dod delete.

@BoBuilds 3 жыл бұрын

The crank pulley seal would be considered the "front main seal" ive never had an issue just torquing the cover down and install pulley through seal. A quick way to center is to wait on tightening the timing cover until the crank pulled is installed through the seal then torque timing cover. Some bolts may be tricky to reach tho

@BoBuilds 3 жыл бұрын

Yeah ls4 is essentially a gen 4 aluminum 5.3

@johnsimun6533 3 жыл бұрын

Just got me a ‘06 Impala. Every once in a while, when she switches to V4 mode. I hear the dreaded tick tick tick. So I am searching for a temporary fix till the DODD. The transmission is a little rough, and suspension is a little banging, but as smooth as a impala running across the savanna full speed. Is there anything else that I need to do while I’m in there?

@eddiej.2354 2 жыл бұрын

WoW if I lived close by I'd have you swap my Z71 cam for something in-between stock and what was swapped as I prefer a sleeper. But Awesome Video! Awesome Step by Step! My only thing is I would have wanted my oil pump replaced as the stock unit isn't know to last. Other than that.. Thank You! 😊 Super Appreciated 😀! Eddie J. Long Island N.Y

@designsinorbit 2 жыл бұрын

I wish more videos like this were in the Tube.

@aaronyork6173 3 жыл бұрын

What camshaft did you use?

@eekl1p271 Жыл бұрын

That’s a btr

@morganthechevyguy 4 жыл бұрын

What are the cam specs on this one?

@jerryrogers2516 2 жыл бұрын

thanks so much please keep the 5.3 coming lol I need all the info I can get. your a life saver

@erictjones Жыл бұрын

Anybody catch the Whitesnake playing while the pushrods were coming out? Oooo Baby!

@Cameron78998 4 жыл бұрын

I'm going to use the 5/16th wooden dowel method! But how can I be sure the lifters are all the way up? Will the dowels get stuck if one is down? Thanks

@loganterry9826 4 жыл бұрын

Yessir, if they don’t go all the way back you still have a lifter down

@thefoot957 4 жыл бұрын

Step 1 should've been to clean all that crap from the cowl. You don't want that crap falling in the engine

@mlm7536 2 жыл бұрын

you da man!!! wish you lived closer because I would hire you to work on my 5.3 sucks that car manufactures get by with flaws in design and manufacturing defects. Chevy AFM and failed lifters the Ford 5.4 Triton spark plug fiasco.

@lexustech48 3 жыл бұрын

Lexus techs getting it done. Nice job.

@TheMastblaster 3 жыл бұрын

Step 50 edit video so it looks like it only took 10minutes when it was actually 8hrs.

@atomic2903 3 жыл бұрын

did u want the video to be 8 hours long ???

@Lwrthnu64818 3 жыл бұрын

Not necessarily 8 hours I’ve done several cam swaps and it typically takes around 4-5 hours for an inexperienced mechanic.

@coreyalvarado666 3 жыл бұрын

What was the point of doing a before rev up? I really wanted to hear the difference after of the new cam besides an idle.

@slickrickjones Жыл бұрын

Welp, it’ll probably take me 6 weeks, $200 in gas running to the parts and tool store, 15 hrs on the phone with friends and KZfaq, $100 tow bill to take it to a garage and finally $1000 for the mechanic to fix my fuck ups that I should have never started. It’s going to run and sound great though! Excited to get started!!