Gsender Complete Tutorial for CNC Routers
Рет қаралды 10,082
Күн бұрынThis video is a complete tutorial of the gSender control software for your CNC router! Whether you're just beginner with your CNC router, or you've been around the CNC router block, this video is a comprehensive guide to mastering the gSender control software.
gSender is a free control software for CNC routers to do CNC router woodworking. It processes gcode to run CNC machines. Not just for CNC routers, but any CNC machine that uses the Arduino circuit board with the GRBL firmware.
I cover all aspects of gSender, from the basics of manual control to the the features that make gSender carve CNC projects. When comparing gSender to UGS, gender is by far superior. NOTE...gSender will run for ios MAC and Windows
It works for Longmill, Shapepoko, Onefinity (some units), BobsCNC, Millwright and others.
What you'll learn:
- How to set up gSender with your CNC router
- The ins and outs of manual control for precise movement
- How to use the probe feature and remote operation
- Setting your project's XYZ start points like a pro
- Monitoring your project's progress on your CNC router
- Tips and tricks to make the most of gSender's features
- gSender surfacing feature, macro, error messages, and troubleshooting
gSender also runs CNC lasers so it is good to run them too!
Download gSender FREE → sienci.com/gsender/?ref=IDCWO...
gSender manual → resources.sienci.com/view/gs-...
DOWNLOADS
gSender error and alarm messages PDF → bit.ly/42LzEGY
------------------------------------------------------
ROUTER BITS FOR CNC ROUTERS
→ 13pc complete CNC router bit set (w/ free design files) www.idcwoodcraft.com/11P-SET-W
→ 1” Surfacing bit required for surfacing your spoil board: www.idcwoodcraft.com/SU-10
→ Glass engraving drag bit: www.idcwoodcraft.com/ED-14
-----------------------------------------------------
VIDEOS MENTIONED
Ultimate CNC router buyer's guide → • The Ultimate CNC Route...
Longmill CNC router review → • Expert Insights: Revie...
Homing sensor/switch video → • Homing Sensors & Work ...
------------------------------------------------------
OTHER ‘MUST HAVES’ FOR CNC ROUTERS
→ Calipers: amzn.to/338MAt3
→ Hearing protection (plugs don't work): amzn.to/2Hs1RgW
------------------------------------------------------
Recommended Design Software
→ Vcarve Pro (RECOMMENDED)→ bit.ly/3d4WrEU
→ Vcarve Desktop → bit.ly/3D4CwjH
→ Vectric Aspire → shrsl.com/37pw9
→ Cut2D Desktop → shrsl.com/36xfm
→ Carveco (budget) → bit.ly/37rhVbY
-----------------------------------------------------
MASTER YOUR VECTRIC SOFTWARE with Kyle at Learn Your CNC
Take the full course ↓
academy.learnyourcnc.com/a/21...
Get Weekly LIVE Training ↓
academy.learnyourcnc.com/a/21...
___________________________
Starbond CA Glue Products
GET 10% OFF when you use this discount code: IDCWOODCRAFT10
---------------------------------------------
Join CNC ENTREPRENEURS Facebook group: / cncentrepreneurs
------------------------------------------------------
CNC FREE STUFF AND MORE
CNC Insiders sign up (free files and more): idcwoodcraft.com/cnc-lp2-free...
------------------------------------------------------
PLAYLISTS
CNC FOR BEGINNERS: bit.ly/3rg4WTl
CNC ENTREPRENEURS: bit.ly/3mxz6Ok
VECTRIC VCARVE & ASPIRE TUTORIALS FOR BEGINNERS: bit.ly/3pdmFsi
------------------------------------------------------
If you currently own a CNC router, please take a moment to take this survey to share your experience with it: bit.ly/3r5XzNh
------------------------------------------------------
Please support the IDC Woodcraft KZfaq channel:
Buy me a cup of coffee: www.buymeacoffee.com/garrettf...
------------------------------------------------------
Cool vector files for CNC router & CNC laser: etsy.me/3oxX79l
------------------------------------------------------
CNC FOR BEGINNERS PODCAST: anchor.fm/cnc-for-beginners
------------------------------------------------------
Garrett Fromme
Facebook: IDCWoodcraft
Website: www.idcwoodcraft.com
Email: garrett@idcwoodcraft.com
#cnc #cncrouters #cncforbeginners #vcarvetutorials #vectric
Phantom CNC Systems → www.phantomcncsystems.com/
-----------------------------------------------------
All-Star CNC Products vacuum mat ↓
www.allstarcnc.com/all-star-c...
-----------------------------------------------------
LONGMILL CNC ROUTER WEBSITE:
sienci.com/product/longmill-m...
@debbieleasure1637 10 сағат бұрын
I am new to cnc. This was the most informative information on g-sender i have found. I have just ordered my longmill and cant wait to start. Thank you for all your videos.
@seniorchief48 7 күн бұрын
Thanks for this info on GSENDER. It has fully cleared up multiple problems that I have been having with my machine settings for the past few months.
@IDCWoodcraft 6 күн бұрын
seniorchief48, I'm glad to hear that the information was helpful for you and that you were able to solve your machine setting problems!
@carld4621 3 ай бұрын
Another timely and valuable CNC resource you are becoming well known for providing. Very much appreciated.
@IDCWoodcraft 2 ай бұрын
carld4621, im glad to hear it brother! Happy CNCing.
@Sh1tzboutagodown 2 ай бұрын
I am proud of you bro, I put my CNC journey on hold and hadn’t seen your vids almost 2 years…….You look great and the content is top notch.
@IDCWoodcraft 2 ай бұрын
Sh1tzboutagodown, thanks brother! Im happy to hear my videos have been helping you for so long. Happy CNCing!
@christophermeade5097 2 ай бұрын
Thank you Garrett! Hoping to get up and running more as April continues.. great content
@IDCWoodcraft 2 ай бұрын
christophermeade5097, you are so welcome brother! I am excited for you to get started.
@eddieyoung8629 3 ай бұрын
Thanks Garrett, I haven't gotten my longmill set up yet because I'm waiting on spindle to set it all up first, so I will be coming back to this timely video again.
@IDCWoodcraft 2 ай бұрын
eddieyoung8629, you are so welcome brother! I am excited for you to get alll set up so you can get to cutting.
@PaulLeenerts 2 ай бұрын
Great job! Very clear tutorial. Thank you.
@IDCWoodcraft 2 ай бұрын
PaulLeenerts, you are so welcome brother!
@joseguevara184 2 ай бұрын
Almost 2 years using it, is the best, the helper to configure my DIY CNC was amazing, it´s really practical and simple, the interfase is very pleasent. Love this. The best for me.
@IDCWoodcraft 2 ай бұрын
joseguevara184, so glad to hear you like gSender just as much brother!
@ifiwooddesigns 3 ай бұрын
So much better watching your videos than going through the manuals! Thanks Garrett! You the man!!! P.S. Something I believe is very important is pausing a job, getting the router/spindle out of the way, and then resuming from that point. That is critical to know especially for beginners.
@IDCWoodcraft 2 ай бұрын
ifiwooddesigns, very good point brother! Glad to hear this one helped you so much. Happy CNCing.
@MegaShedWoodWorks 2 ай бұрын
Garrett, thanks so much for this video. I use both Easel Pro and Vectric Pro to design. I send gcode from Vectric Pro to Easel Pro for carving. I have been using Easel Pro for a few years now since it was what I learned on. I could never get UGS or gsender to connect to my X-Carve Pro. Yesterday, I got it connected and used it to flatten a piece of wood. Then I flattened a few more. Tonight, I did my first project with it. It turned out great. I will be using it more now. All due to you. I always watch your videos to learn from.
@IDCWoodcraft 2 ай бұрын
MegaShedWoodWorks, you are so welcome my friend. Keep working hard and learning everything you can.
@Sbregher 2 ай бұрын
Thanks for the great video!
@IDCWoodcraft 2 ай бұрын
Sbregher, you are so welcome my friend.
@hamanjam 3 ай бұрын
You skimmed completely over the job history which covers maintenance reminders and timings. Very useful for people who don’t know when or what maintenance to do. I would recommend also covering with the home sequence enabled which shows the home and quick move buttons to replace the macros to move out of the way. Warning in workspace reset was highly requested because people click by mistake so that saves having to reset. Numerous other items skipped for a complete video. I would recommend collaborating to fully cover some of the topics
@IDCWoodcraft 3 ай бұрын
Hi Hamanjam. Thank you. I'm sorry this video failed your expectations. I hope you got something out of it regardless. We will definite;y have to colab
@hamanjam 3 ай бұрын
@@IDCWoodcraft I wouldn’t use the term “failed”. Just suggesting to pick up a couple points of the new features we’ve been asking for which shows they are indeed listening to the community and adding new features.
@andrewtaylor4554 2 ай бұрын
Make ur own vid with the minimal voids n u might get a utoob plaque …. Cheers
@josephkickbusch340 Ай бұрын
As always you r the best
@IDCWoodcraft 29 күн бұрын
josephkickbusch340, Thank you so much for your kind words! I'm glad you enjoy the content.
@ramijali6964 2 ай бұрын
Wow that's awesome great video thank you sir❤❤❤
@IDCWoodcraft 2 ай бұрын
ramijali6964, you are so welcome my friend.
@riazmughal2922 3 ай бұрын
Very nice new information
@IDCWoodcraft 2 ай бұрын
riazmughal2922, so glad to hear that brother!
@davidwagner8356 2 ай бұрын
I’ve used gsender on raspberry pi 400 to control my cnc. Works good.
@IDCWoodcraft 2 ай бұрын
davidwagner8356, that is a good setup you have there brother! Happy CNCing.
@DustyWoodcutter 3 ай бұрын
Thanks Garrett
@IDCWoodcraft 2 ай бұрын
1HughJardon, you are so welcome my friend.
@danneil7806 2 ай бұрын
Tried to send a tip. denied twice. Wanted to encourage you to do more videos going deeper into this. Had the latest version of GSender, but had too many "funky chickens". So downgraded to 1.2.2. Now it only hiccups on one item that I can easily deal with. Learned a few things that are nice to know. Looking forward to part 2 !!!
@IDCWoodcraft 2 ай бұрын
danneil7806, im sorry to hear you are having difficulty with the latest version of Gsender brother but it sounds like you are right on track with v 1.2.2! Happy CNCing.
@oldmanwoodcraft Ай бұрын
Thank you so much for this deept step by step tutorial.i got 2 questions. 1. can you operate the spindle (speed and operating test) 2. how do you control and run 4th axis like a rotary ? in Gsender
@IDCWoodcraft Ай бұрын
oldmanwoodcraft, I recommend reaching out to longmill directly on this one my friend. They should be able to give you a little better guidance than I can on this one. Here's the link to their contact page →sienci.com/contact-us/?ref=idcwoodcraft.
@oldmanwoodcraft Ай бұрын
@@IDCWoodcraft Thank you so much i will send them a message
@mikeprestone8367 2 ай бұрын
Thanks for all you do and the effort you put forward to teach us. Been watching you for a while and just started using Gsender. I would love to know what happened between 13:00 and 14:00 when you were describing using macros. It seems like you wrote a macro, ran it, and things went south. No biggie, but where you describing how the alarm and unlock works? Why did the macro go bonkers or where you trying to show how to handle an error???? I picked gsender because it has the macro capability, but now I'm a little confused about it not working like you thought it would, or was that on purpose and I didn't get it??? Again, thank you for all you do for us CNCers. You are killing it!!!!
@IDCWoodcraft 2 ай бұрын
MikePrestone, I’m thrilled you’ve been finding the videos helpful and are diving into Gsender! Macros can be pretty nifty, but also a tad tricky. So about that hiccup during the live demo-ah, the joys of live tutorials, right? It wasn’t exactly planned to go awry, but it did turn into an impromptu lesson on troubleshooting and using the alarm and unlock features. CNC adventures often include unexpected twists, and it’s all part of the journey. When writing or running a macro, a slip in the code or a machine quirk can send things off course. It’s not the macro capability itself but more about the details in the script or the machine's current state that can lead to surprises. If you’re keen on using macros, go for it! They can be huge time-savers. Just remember to test carefully and maybe not on your prize piece of stock right off the bat. And if you hit a snag or something doesn’t work as expected, it’s all part of the process. Unplanned lessons are sometimes the best teachers brother! Keep at it, and Happy CNCing brother!
@eileenbaker6419 2 ай бұрын
hello..will be first time CNC user at a community workshop.. they gave a quick lesson on the actual machine use and will supervise first cut.. they have Gsender set up on their computer.. my first project will be to resurface a 2 inch cypress shelf I want to install in the cabinet space over my refrigerator.. i was going to try to find free software to design the necessary file to surface my project but I see from this video that Gsender has a surfacing feature.. could i accomplish my project resurfacing using only Gsender? i purchased your 1.5 surfacing bit which i plan to bring and use..thank you for this video and your other content.. who knows, maybe i'll get my own CNC at some point.. you sure make it look learnable and fun!
@IDCWoodcraft 2 ай бұрын
eileenbaker6419, you sure could brother! I also have a video that should really help you with surfacing. Here is a link: kzfaq.info/get/bejne/gpOka7KH09-xmJs.htmlsi=97ypugYrN85Ytfko
@eileenbaker6419 2 ай бұрын
@@IDCWoodcraft thanks Garrett..actually a "sister" here .. i have previously seen and learned a lot from your referenced video about surfacing.. As you responded, i was actually editing my original post to ask about something i saw in that video..I see in the creating toolpath section, the need to "add" the surfacing end mill and check for correct settings.. if i only use Gsender (i dont have design software and and wouldnt acquire just for this project, unless there is something free to use), would this step of adding the bit be necessary or accounted for? thanks again, Eileen
@rbwoodwork1890 2 ай бұрын
Good video as always. Not sure you will see my question but when I hit the zero xyz button my z goes all the way up to the stop switch and I lose the z zero setting and have to reset it again. Not sure whats going on or how to fix it. Thanks
@IDCWoodcraft 2 ай бұрын
rbwoodwork1890, you are so welcome my friend! Happy CNCing.
@bloomqmx 2 ай бұрын
Hey Garrett I'm wondering if this g-sender will work with my Nextwave HD500? I am using Ready2Control pretty basic. thx for what you do!!
@IDCWoodcraft 2 ай бұрын
bloomqmx, reach out to Nextwave on that one brother. They would be able to determine compatibility for your specific machine.
@mikeamescreations 2 ай бұрын
Hey Garrett, Can I change the feed rate on the fly while job is running?
@IDCWoodcraft 2 ай бұрын
mikeamescreations, you sure can brother! This would be a great idea for a future video. Ill add it to the list!
@JackNess-yq8hk Ай бұрын
Hey there. I've been learning a lot from you, but I have a small problem. My gcode sender tells me I'm connected, but the screen below says I'm disconnected. I'm using another computer, much slower than my laptop that I'm waiting for parts to fix the charging jack, but is this normal??? Let me know! Thanks again for giving us all what we need to know about CNC.
@IDCWoodcraft Ай бұрын
JackNess-yq8hk, Unfortunately, I am not much help here. I am not a tech guy when it comes to CNC machines. I may be good with the programing and operation but when it comes to troubleshooting, I'm an absolute deer in the headlights. I recommend reaching out to your machine manufacturer regarding your issue. They will be able to help you the best my friend!
@w4fej 16 күн бұрын
Is Gsender for Longmill only ?? I have two machines, are there post processors built into ?? I have the Shapeoko XXL 3 and the "CNC One Max".
@IDCWoodcraft 16 күн бұрын
w4fej, Gsender is compatible with a variety of CNC machines, but it is best to check with your machine manufacturer to determine compatibility. Feel free to give it a try and see how it works for you!
@SenniMusic Ай бұрын
I am trying to use this software with my cnc xprov5. the software do not connect to my cnc. It recognizes that I have two firmaware, but I cannot click on the arrow appearing in the drop down menu. It works with CNC3D Commander. I would like to use this sofware but I wonder it is for their cnc machine.... Is it possible to use it with CNC xPRO V5?
@IDCWoodcraft Ай бұрын
SenniMusic, for this one brother I would recommend reaching out to your machine manufacturer. They can help you with your specific CNC on compatibility.
@ramijali6964 2 ай бұрын
Sir I have port connected but visualizer is not connecting. I was all of try but I can't connecting visualizer. If there any else. Give me feedback. I'm helpless
@IDCWoodcraft 2 ай бұрын
Unfortunately, I am not technical on this. You might want to contact longmill since they are the makers of the software.
@pw3111 2 ай бұрын
I would have gone into detail on setting up the probe in settings. You covered setting up the bit diameter but totally missed setting the thickness of the probe material in Z, X and Y directions which is essential for accurate zeroing. Otherwise a good video.
@IDCWoodcraft 2 ай бұрын
pw3111, good points brother. I will focus in on that more in future videos.
@RVE7777 2 ай бұрын
Hi,I want to ask did the Gsender is compatible with all CNC routers ?I am waiting my from China it will arive at the end of April and Im wonderin if I can connect it to this software.Thank you I appreciate for all the videos you make Ive learned a lot !
@hamanjam 2 ай бұрын
gSender should be compatible with controllers running grbl firmware. There will be configuration you will need to research with your manufacturer but if you can use UGS, you can use gSender
@RVE7777 2 ай бұрын
@@hamanjam nk105 g3 control system this is the controler .Can you help me ,does it have this firmware?
@hamanjam 2 ай бұрын
I’m not familiar with this controller but it does not appear to support .gcode or .nc files. It looks like a Cortex A8 processor so my guess is that it would not work for you.
@RVE7777 2 ай бұрын
@@hamanjam thank you!
@IDCWoodcraft 2 ай бұрын
radoslavevtimov6448, that depends on your machine brother! Your best bet is to reach out to your machine manufacturer to determine compatibility.
@richardwilliamsjr.6090 2 ай бұрын
I use Carbide Motion as my Cam software. Is G sender better ?
@IDCWoodcraft 2 ай бұрын
richardwilliamsjr.6090, I recommend giving them both a try and seeing what you think brother! As long as they are both compatible with your machine!
@geegonzalez8042 28 күн бұрын
looking for a laptop to run gsender do you have any recommendations thanks
@IDCWoodcraft 27 күн бұрын
geegonzalez8042, I recommend looking into laptops with at least an i5 processor and 8GB of RAM to run gsender smoothly. You might also want to consider a laptop with a dedicated graphics card for better performance. Here is a video that should help: kzfaq.info/get/bejne/j9GWp9Vlvt6zgqs.htmlsi=Fk6_6HbgLyFARwoY
@kennethduke9383 25 күн бұрын
Will G-Sender work with a Shark CNC? And can a Vetric file be emported to G- Sender.
@IDCWoodcraft 24 күн бұрын
kennethduke9383, consider reaching out to Shark brother! They will be able to give you the best compatibility suggestion for your specific machine.
@arbjful 2 ай бұрын
Does this have feed overrides?
@IDCWoodcraft 2 ай бұрын
Yes. That was notes in the video. I don't remember the time stamp when I discuss it though
@Barry-mw6tk Ай бұрын
Will this sender work with X-carve
@IDCWoodcraft Ай бұрын
Barry-mw6tk, your best bet is to reach out to x-carve on that one brother!
@JavierDeJesusSr 2 ай бұрын
I've been using UGS up to now. Is there a reason to switch?
@IDCWoodcraft 2 ай бұрын
JavierDeJesusSr, if UGS works for you then stick with it brother!
@JavierDeJesusSr 2 ай бұрын
@@IDCWoodcraft not married to it, just haven't tried anything else.. I'll give gSender a go and see if I like it better. Can I set up a game controller for it?
@donripperger6764 3 ай бұрын
does Gsender software work on a Mac?
@IDCWoodcraft 3 ай бұрын
Yes!
@coreyjackson1594 2 ай бұрын
do you have cnc classes?
@IDCWoodcraft 2 ай бұрын
coreyjackson1594, not yet brother! But that is something that is in the works my friend. Thank you for the nudge.
@IceCreams62 3 ай бұрын
Hi. In a Mac it runs also on M1 family processors ?
@hamanjam 3 ай бұрын
The "official" response in GitHub as of 3 weeks ago: "We had plans to add the macOS ARM64 build for gSender a little while back but we unfortunately need to push it back for now as we have other features to focus on. We will add it to the patch notes once ARM64 is part of our build process :)"
@IceCreams62 3 ай бұрын
@@hamanjam thanks a lot
@IDCWoodcraft 2 ай бұрын
IceCreams62, not yet brother but I know they are still working on it and hopefully it is out soon!
@IceCreams62 2 ай бұрын
@@IDCWoodcraft Thanks a lot, i will wait 🙂
@booyahhh4642 3 ай бұрын
Man I’ve had all kinds of issues with gsender. It connects sometimes and other times it won’t connect no matter what I do.
@IDCWoodcraft 2 ай бұрын
booyahhh4642, im sorry to hear that brother. Try reaching out to Sienci, they should have some troubleshooting tips to help you figure that one out. Here is a link: sienci.com/gsender/?ref=idcwoodcraft
@davidbate3453 2 ай бұрын
I plugged mine in and it said fake comm port
@IDCWoodcraft 2 ай бұрын
davidbate3453, im sorry to hear that brother. Try reaching out to Sineci regarding your problem. They will be able to help you with that. Here is a link: sienci.com/gsender/?ref=idcwoodcraft
IDC Woodcraft
Рет қаралды 120 М.
Poly Holy Yow Spanish
Рет қаралды 27 МЛН
IDC Woodcraft
Рет қаралды 352 М.
IDC Woodcraft
Рет қаралды 78 М.
Fat Lip Collective
Рет қаралды 15 М.