Just a short video on why I have a Bosch drill with SDS
Пікірлер: 26
@TheBootyWrangler2 жыл бұрын
On your “I wish all drills had this type of bit” point That is one of the many reasons why I fucking love impact drivers
@johncooper4637 Жыл бұрын
SDS is definitely the way to go. I have the smaller Bosch model 11224 VSR and have used it a lot. It is great for drilling holes in concrete for anchoring equipment. It has enough power that drilling a 5/8" hole for 1/2" anchors takes no time at all.
@Tools-Tested Жыл бұрын
Yep 110% SDS is awesome!
@TheBootyWrangler2 жыл бұрын
“I need to drill a lot of holes in concrete…” … I’m so sorry my friend
@LemonySnicket-EUC2 жыл бұрын
On that red Milwaukee chuck, make sure you tighten it up using all three chuck key guide holes to tighten it up in a uniform manner. It works much better when you do.
@RK-pf7jc3 жыл бұрын
You have real experience and have conveyed what matters so thats useful. A small tip is to pre-arrange all the drills upfront rather than boxing-unboxing so that the video is crisp and short and for better focus on the main content. Overall thumbs-up for the content
@Tools-Tested3 жыл бұрын
Thanks! Yeah I’m definitely new to this....lol hopefully I get better.
@johnlewis7772 жыл бұрын
Good comparison, thanks
@Tools-Tested2 жыл бұрын
Thanks for watching!
@kgunderson90032 жыл бұрын
thanks. most informative
@Tools-Tested2 жыл бұрын
No problem, Thanks For Watching!
@madenod51455 ай бұрын
No practical video with all 3 drills?
@gf2e2 жыл бұрын
Very useful video. You said you wished normal drills had SDS chucks - can’t you just use one of these for all your drilling? All the SDS drills I’ve looked at had the ability to turn off the hammering.
@Tools-Tested2 жыл бұрын
Thanks, Hi, yes you can turn off the hammering and use it like a normal drill, but you would then be using normal drill bits not SDS. From what I can find SDS bits are only for masonry/concrete.
@kafkaMtАй бұрын
you dont have to grase those?
@Tools-TestedАй бұрын
Yeah SDS needs to be greased.
@kafkaMtАй бұрын
@@Tools-Tested I see thank you, I thought all would have the open disc on top.
@bat__bat Жыл бұрын
Not one, but TWO fifteen second, un-skippable pre-roll ads? Wtf
@keletienne79476 күн бұрын
Not the KZfaqrs fault buddy
@clone11372 жыл бұрын
4:09 do you not know how to lock your chuck? Once you’ve ratcheted the chuck on the bit as tight as you can turn it slightly in the loosening direction. You will hear one click and the chuck is locked. The chuck will not loosen, your bit will not slip. All modern corded and cordless drill operate like this. I’ve seen guys with decades of experience not know this, and I recently learned that myself. But let me tell you it’s life changing.
@Tools-Tested2 жыл бұрын
Yeah sadly l recently learned this… I probably should make a video about it.
@clone11372 жыл бұрын
@@Tools-Tested it’s like they expect to read the instructions or something lol
@Tools-Tested2 жыл бұрын
@@clone1137 Lol I tend to read them more often the older I get.
@louisd957146 ай бұрын
Wrong! What you are suggesting has been proven false. The bits are not secured more by clicking once to the opposite direction. There was a recent video out where the chick manufacturers have proved this wrong.
@louisd957146 ай бұрын
@@Tools-Tested You've been doing it correctly all along. What clone 1137 has suggested is totally incorrect.