Damn u saved me bro, the whole time I thought I had the wrong part..💯💯💯💯
@redhytech4 ай бұрын
just got a ESE for my 2023 GSX-S1000 GT. will install it this week end. part number ESE-S04.
@SnelleJelle_3 ай бұрын
and is it, it worth?
@redhytech3 ай бұрын
@@SnelleJelle_ I unhooked the cables to the exhaust valve, and that caused an FI error. the ESE took care of the error message. but as far as performance of the bike??? no,, nothing changed.. it doesn't get louder, it doesn't have more power, it doesn't lose torque. if you remove the servo you lose a little overall weight of the bike, but not enough to matter.
@mauricecooper90165 жыл бұрын
Just what i needed. Thanks bud
@Sibicheteam4 жыл бұрын
Thanks buddy ! Crystal clear ! :D
@fishnmaster4213 жыл бұрын
Is there a wire to remove on the 2013 like there is on the k7 esc to remove the fi light without a servo buddy? The #30 pin on a 13 model don’t have a wire there in that spot to remove
@LiShion_3 жыл бұрын
Thank You!
@tristinlee56064 жыл бұрын
I have a gsxr 600 2013 but the servo buddy that i order was supposed to fit my bike but it is 2 plug ins
@fishnmaster4213 жыл бұрын
Did you get a single plug one?
@MoodSwingZX4 жыл бұрын
I am goin to flash it and do the TRE on ECU.
@RobertDamien86874 ай бұрын
How do you do the tre on the ECU?
@JohnBautista-mk2ys5 ай бұрын
I’m noticing a lack of power when I punch the throttle!!! I feel like I’m riding a 300
@majidrahimi21152 жыл бұрын
Hello, I also have a Suzuki gsxr1000///2009. There is no electricity in the fuel pump socket, what could be the reason?
@harshwardhanpatil30305 жыл бұрын
Hi im planning to put competition werks exhaust on m821 18 will servo buddy give bettter performace if i install it wid better air fuel ratio..and run leaner?
@TheConstitutionState2 жыл бұрын
that's a pain in the ass😂, my k6 it's on the tail mounted to the sub frame. I just had to pull all mine off I did the same thing
@alycastillo7325 Жыл бұрын
Hi, I want to Do on my r1 but nothing bad happened on the engine? Thanks
@kapoklo13 жыл бұрын
Did you remove the butterfly valve too?
@groupecmp94362 жыл бұрын
How do you remove the oem servo motor and cable? Im right into the installation and i really dont know what to do after taking out the 2 bolts… can’t see anything. Do we have to remove something under the bike to? The actual vavle? Or we just need to figure out how to remove cables from the servo motor? Thought it was an easy install after seeing your video but now im fucked during the installation. Can i leave the oem motor in place and just unplug it and plug my Healtech servo exhaust eliminator thingy? I have the same exact bike as yours..2013 blue and white 750.
@ladiezman2392 жыл бұрын
You can just leave it on, just unplug it and plug it the ese
@groupecmp94362 жыл бұрын
@@ladiezman239 oh really? So the vavle will stays open always? When the bike is turned off, the valve keeps its open position? So i can put back the 2 bolts keeping the oem servo motor there, and just deplugg it and plug my ese right? Turn it on and bingo?
@ladiezman2392 жыл бұрын
If you have an aftermarket exhaust, you should of took off the cables, that's why I don't have any in the video
@groupecmp94362 жыл бұрын
@@ladiezman239 i just have an m4 slipon so oem stuff still there. So i will try what u said leave everything there and just plus the ese !
@ladiezman2392 жыл бұрын
@@groupecmp9436 Yes, since it's connected to the cat, are you getting an Fi light?
@marcwazen295110 ай бұрын
Anyone got problems caused by the ESE? Plugged it on my bike, rode it for 30min then the engine suddenly failed. Unplugged it then engine worked fine
@madasabike Жыл бұрын
Hi before you install ese was your ECU flashed or remapped thank you
@ladiezman239 Жыл бұрын
No
@madasabike Жыл бұрын
Ok before you put ese on did you have herky jerky at low speeds
@edmundsenterprises9786 Жыл бұрын
@@madasabikeI had the herky jerky for sure.. yank that shit out.. plug in eliminator and have crisp smooth throttle. Let me guess, your bike feels like the power completely cuts out on decel then jumps all over on acceleration making slow corning about as sketchy as possible??