Another of your video's I've used. If only you still had your XF !! Thank you for the perfect video again.
@malcolmjones76505 жыл бұрын
Just wanted to say thank you for this patticular vlog I followed your instructions and now have LED side lights which make the car so much better.
@carfanfan5 жыл бұрын
Hey always great to hear success stories. Thanks Malcolm
@laurencetitusoates63282 жыл бұрын
Thanks, the only vid on YT that showed me how to do this easily.
@alexzarmmckenzie60236 жыл бұрын
Hilton, I was a tad dubious in doing this but after watching your video it shouldn't be a problem. love the music ...you have a subscriber
@carfanfan6 жыл бұрын
Thanks for watching Zion. Glad my video could help. You'll see, it's quite easy to remove the head lights. I have a later video where I finally did replace those bulbs with LED's - I learnt a lot before I could do that video. Glad you enjoy the music. You can check it out at xcapemuzik.bandcamp.com/
@tony404004 ай бұрын
Thanks for the prompt reply, my XF has the washer built into the headlight (the silver panel bottom centre), so looks like the are 2 variants. I will have to dig further, thanks
@carfanfanАй бұрын
There are two variants indeed. But dealing with the washer nozzles is not difficult. You will see once you get the bumper off.
@AndrewKNI7 жыл бұрын
Great instructional video Hilton. You make it look so easy :-)
@thehammermanduke Жыл бұрын
This is some good stuff right here. Thanks for the video.
@nevillefletcher75187 жыл бұрын
Very good video, thanks it will help a lot of people
@tony404004 ай бұрын
Great video, can not see anything on connecting the washer hose to the headlight unit. Is there 2 versions of headlight unit 1 for waser and 1 without, thanks
@carfanfan4 ай бұрын
Yes. My headlights didn't have washers, but if you watch my video of removing my XFR bumper you can see how to disconnect the washers. Very easy to do.
@kennethgreen84133 жыл бұрын
Thanks looks easy
@promariossigma25566 жыл бұрын
I checked today the book and doesn't exist fuse for xenon inside.i checked in engine bay and in truck but wasn't there too.i will check tommorow the interior fuses too.thank you for your answers
@carfanfan6 жыл бұрын
Promarios Sigma I checked my manual and they are in the engine compartment. F16 mini Left Hand 20 AMP Yellow F17 mini Right Hand 20 AMP Yellow Engine compartment, 2nd row from the left of mini fuses. It'll be the 3rd(F17) and 4th(F16) from the bottom of that row.
@MH30R7 жыл бұрын
Thanks Hilton. In your opening introduction, you mentioned you did not have the correct adaptor rings for the bulbs you were trying to install. Are all of your bulbs standard halogen or do you have Xenon's in the low beam? In the Australian model MY2011, I have Xenon Low Beam that take a D1S bulb and I needed to remove a collar/adaptor from the old bulb in order to fit the new bulb. Initially I thought I had the incorrect bulb, but with closer examination and a little exploring of the differences, we realised our error. With the high beam, I have just completed a Full LED conversion from USA and an adaptor from China. The H7 replacement LEDs and Drivers were all mounted comfortably within the high beam enclosure. I took it for a drive last night and the beam pattern is identical to the original, but at least twice the apparent brightness. Some road signs give strong reflections, which may be problematic, but you can see other objects on the road or roadside more clearly for a greater distance. My opinion and my subjective testing, but a great mod from my perspective with no error codes generated. Also did LED W5W side/parking bulb replacements and the colours now match the HID low beam and LED high beam. I am considering a post of my LED conversion on the Jaguarforums.com site.
@carfanfan7 жыл бұрын
MH30R Thanks for your comment bro. I really would appreciate you putting something up on the forum because I used the H7 halogen adapter but found that the collars that screw into the headlight fitting aren't high enough. I bought two different sets of LED bulbs and neither would fit. It came down to the adapter not being the same as the original one which has a square center. It would be great if you could give me a link where I can find the adapter you bought. I got mine off eBay. Thanks again.
@MH30R7 жыл бұрын
I got my H7 LED adaptors from here, also on eBay: www.ebay.com.au/itm/232233094832 These ones have a 19 mm circular centre to take the LED body/barrel. There was a removable collar on the LED body which this adaptor fitted nicely behind. I did not do any modifications to the headlight or harness or LED or adaptor. They all fitted together well. I have also posted a pictorial and description thread on Jaguarforums.com here: www.jaguarforums.com/forum/xf-xfr-x250-44/xf-2011-led-high-beam-conversion-182409/ Good luck with your mods!
@carfanfan7 жыл бұрын
MH30R Thanks bud. I read your tutorial (very well written and illustrated), and now I see the difference. You adapter on the later models is different to the earlier models. Also, your headlight housing seems to have two "screws" either side where the adapter clips into. Mine doesn't. It has two raised hooks that are welded onto the housing where the H7 ring clips into. And the ears of the adapter ring are higher to accommodate the space between bulb and headlight. Perhaps I'll do a video of that to show everyone what I'm talking about in the hope that there's a simple fix for this by buying an adapter like the one I have now ;-) Thanks so much for posting that tutorial. Much appreciated.
@carfanfan7 жыл бұрын
MH30R You won't believe this! After trawling eBay I found the ones that fit my car. They are slightly different to yours but look the same. One has to have an eye for detail on these things. Here's the link m.ebay.com/itm/H7-LED-KIT-Holder-clips-Adapters-BENZ-E-class-CLK-BMW-5-SERIES-E350-528i-E60-E61-/232342162499?hash=item3618ac0c43%3Ag%3A0pQAAOSwcaFZH2YK&_trkparms=pageci%253Abcd191dc-3e56-11e7-8c19-74dbd1805154%257Cparentrq%253A2c5b2b3715c0ab19f229c489fffea20b%257Ciid%253A1
@MH30R7 жыл бұрын
Well done. Hope it goes well and I am learning that there are several variations in all things electrical between years even for the same model. Would like to see some photos or video of your install also.
@engaziz55537 жыл бұрын
very useful video. could you please post a video about how we can remove the roof liner in jaguar xf ?
@carfanfan7 жыл бұрын
eng aziz Woah, thanks, but I wouldn't want to take mine off unless I absolutely had to :-D
@engaziz55537 жыл бұрын
thanks anyway, I appreciate your effort.
@autotrimmers63532 жыл бұрын
Awesome
@asemarida35033 жыл бұрын
Master Hilton, my jaguar xf 2009 has some dumping sound in the gear tunnel but works good. My friend told me the transmission switch needs reprogramming , is there's something named like that? Thanks alot..
@rusykohli5426 Жыл бұрын
Hi Carl. Is there anyway to replace D3S Bulbs on a 2103 (facelift) 3.0 diesel, XF, WITHOUT removing the bumper ?? 🥴🥴🥴
@carfanfan Жыл бұрын
Unfortunately not. The facelifts headlights have a bottom lip which the bumper clips into. It has to be removed tonget the headlights out.
@kingjulien95254 жыл бұрын
So much pain just the switch bulb. I miss my Hyundai Sonata 05 lol Thank you!!
@carfanfan4 жыл бұрын
This one was easy compared to my new XF - the entire bumper must be removed 🤪
@kingjulien95254 жыл бұрын
Once again, thank you; I have to admit that it wasn't fun at all, but at least I saved a lot. Dealer would charge me triple for the bulb, $100 + labor fees, disposable trash fee. Total would be around $200-300. I learned something yesterday. Got that car since 2012, will never get another Jag in my life.
@severnsea3 жыл бұрын
@@kingjulien9525 Lots of cars have similar procedures, it's no doubt to make people use the main dealers but to be honest I just did this to change my sidelamps and the whole process was simple. Undo 3 bolts, pull the housing out, change the bulbs put it back. I'm not usually a very practical person but this was really easy.
@kingjulien95253 жыл бұрын
@severn sea True that. I was the same as well. But watching those DIY tutorials are very helpful. First time it took me 30min, then around 15, the other day less than 5min. I even removed the front bumper last year to push back the fake air vent. That was entertaining. Anyway thank you. As I said before, I don't myself having another car until this one dies on me.😷🤣😅
@Rickbearcat4 жыл бұрын
The headlight tab that connects the upper left side to the car on mine broke off. So, I need to replace that passenger side light (the same one as yours but I'm from America). The one thing that I didn't see you explain or talk about was the washer system incorporated into the light assembly. You did not mention anything about how to properly disconnect it. In fact, you didn't even seem to notice it at all since there was nothing that was disconnected or reconnected when you pulled it off or put it back on. Is it possible that your car did not come with this headlight washing option?
@carfanfan4 жыл бұрын
Hey Rick. Mine didn't have headlight washers. It's easy though, once you get the headlight loose, just as you would disconnect the wiring loom from the light, you simply unplug the washer on each light. It's just a rubber hose that fits over a plastic grommet. Very easy to undo and reinstall again. 😉
@Rickbearcat4 жыл бұрын
@@carfanfan ...Excellent. Sounds about as hard as undoing the bolts. Thank you for that advice!
@aDIYCarGuy7 жыл бұрын
nice video, your yard is nice! which adapters were they?
@carfanfan7 жыл бұрын
a DIY Car Guy Thanks. Its those standard ones you find on eBay. They look similar, but the ears that clip into H7 bracket are too short and low. Audi and Merc have a similar setup. But these don't work on Jaguar :-(
@promariossigma25566 жыл бұрын
Thank you Hilton!very intersting.but i have in book in engine fuse 9 too hmmm
@3030hp Жыл бұрын
Greetings brother, do you know if 2010 Jaguar XF will give off CANBUS errors if you were to install a LED in a normal-halogen situation?
@carfanfan Жыл бұрын
The answer is, no it won't. I upgraded this particular cars headlights to LED and it worked fine. The indicator is the only thing that gives a canvas error even with canvas bulbs. I did a video on it.
@3030hp Жыл бұрын
@@carfanfan Excellent, thanks for the awesome insight. I will be taking headlights off, doing a complete restore and adding them back in w/ some fresh new LEDs for an awesome new look.
@BaskaranD3 жыл бұрын
Hey Hilton, a very informational video, Thank you!!. I'm trying to change the ballast of my 2014 XF on the passenger side headlamp. Can you please tell me what tools do I need?
@carfanfan3 жыл бұрын
Very easy job. If you have a basic rachet set and some torx screw drivers you would be set to go . 😉
@BaskaranD3 жыл бұрын
@@carfanfan You didn't mention that 2014 model (facelift) needs the front bumper to be removed! But I somehow managed to get the headlight out without removing the bumper fully. The problem now is - even after changing to new ballast & new HID light, its not working. What else the problem could be? Please help!
@severnsea3 жыл бұрын
@@BaskaranD This video is for the pre-facelift model, you can easily see that from the video. Most of these guys are working on their own cars, not covering every eventuality for every model. Re. the problem, sounds obvious but have you checked the fuse? Lots of people don't. If that's not the problem you're better going to an auto electrician if you're not sure what you're doing or what to look for, vehicle electrics can be complex now on many cars.
@papongmalekana77433 жыл бұрын
How to find you. Have same problem Jaguar model 13/14.
@carfanfan3 жыл бұрын
I'm afraid the procedure is very different on the facelift models. The entire bumper must be removed to get the headlights out.
@valentinpavlov80824 жыл бұрын
Thanks for this . I wanted to go to a mecanic to change a bulb. Felt so stupid.
@carfanfan4 жыл бұрын
Glad my video helped 😉
@valentinpavlov80824 жыл бұрын
@@carfanfan i didnt knew about the under wheal wing preson . I felt so fucking stupid after.
@carfanfan4 жыл бұрын
@@valentinpavlov8082 don't feel stupid, it's impossible to know where they hide all the nuts and bolts 🤣😂. I had to figure it out as I was filming 🤣
@severnsea3 жыл бұрын
@@carfanfan That's the reason they do it, they want people to take the car into the dealers. Lots of cars have similar quirks. To get to one of the sidelight bulbs on my Volvo I had to disconnect the screenwash pipes and take the washer bottle off.
@christophercroft98246 жыл бұрын
Would this process be the same for my Jaguar XJL Portfolio?
@carfanfan6 жыл бұрын
To be honest, I'm really not sure. But I would suspect its pretty similar as their design is similar. What I suggest you do is take a look on eBay at some headlights for Jaguar XJ's and that will give you an idea where the screws and mounts are that hold it in place. I don't think you need to remove the bumper on an XJ to take the headlight out either.
@christophercroft98246 жыл бұрын
Cheers mate. Your Jag is immaculate.
@wirefan19825 жыл бұрын
@@christophercroft9824 did you ever find out?
@promariossigma25566 жыл бұрын
And where are located the fuse for xenon?what number they have and how much amb they are?and where is located the passenger side interior fuse box?thank you
@carfanfan6 жыл бұрын
Promarios Sigma I don't actually know all the answers to your questions, but recommend you take a read at your owners manual. There are three fuse panels, one in the engine bay (probably where the xenon fuses are), one in the drivers foot well (passenger on RHD models) and one in the trunk by the battery. Hope this helps.
@AsifSiraj6 жыл бұрын
Have you changed your indicator bulbs to Led?
@carfanfan6 жыл бұрын
Unfortunately its not possible unless I install a transistor between the lights and the plug for the bulb - I left it because I don't want to cut my original wiring.
@promariossigma25566 жыл бұрын
Is the xenon ballast chip inside lights or is located to another place??
@carfanfan6 жыл бұрын
The Xenon ballast is situated underneath the headlight housing on the outside. Be careful, it can store large amounts of power even when unplugged.
@adm612996 жыл бұрын
would the newer headlights on 2013 and up fit on my 09 xf, if i replaced the hood
@carfanfan6 жыл бұрын
Unfortunately not. You have to change the hood, fenders and bumper as well as the front apron to which the bumper, hood and headlights attach to. Better to just buy a facelift version 😉
@adm612996 жыл бұрын
@@carfanfan Thanks. But what is the facelift, and where do I get it from. Also, do you know where do I get replacement plugs for wire harnesses. The three under the passenger seat (left driving) got water and got corroded.
@carfanfan6 жыл бұрын
@@adm61299 The facelift came out 2012. I'd suggest a breakers yard for the harness. Best place to get spares like that.
@iCOLLECTgoats2 жыл бұрын
Does not apply to the 2013 xf
@carfanfan2 жыл бұрын
Correct - it's a bumper off job on that one mate
@rayvazquez56334 жыл бұрын
What years is this jaguar?
@carfanfan4 жыл бұрын
This was a 2009 model
@stephrusty3055 Жыл бұрын
Didn't you have to remove headlight washer pipe .
@carfanfan Жыл бұрын
No
@afifelbaba55355 жыл бұрын
How can we clean the headlight from inside?(removing the glass)
@carfanfan5 жыл бұрын
I'm afraid removing the plastic lens is the only way. You need to warm the entire headlight to make the sealer soft then you can pray it off
@afifelbaba55355 жыл бұрын
@@carfanfan if we remove it would it effect on the long term?(ex: water entering )
@carfanfan5 жыл бұрын
@@afifelbaba5535 Not if you seal it properly again with black silicone sealer. It should be just fine.
@darrenwhite505 жыл бұрын
I have xkr, probably similar removal technique , what about the headlamp washer, i couldn't see any pipes being removed? Mine aren't working at the moment. Thanks