17:21 Wait so to understand, the purpose of the breaks acts like a steering, like if you wanted to go left you'd have to break the left break in order the right tracks push the tank to the left... Smart.

I like that it’s direct drive but for Safty you should put a clutch on that engine so at idle it’s not trying to take off on ya

I've would have reversed the master brake cylinders so you pull not push the levers, so it would be more natural in way of you are braking that side(or slowing down that side) to turn! With the fact that I'm going to guess you'll be adding a throttle petal to rev up the engine which will in gauge the engine to the transmission as well!

The tank is looking great my friend !! Will it have a working turret? We will see . Man it's been just awesome watching you build it ! Your next project after this one will be a joy to watch to .

Thanks for adding captioning!

It will move forward, but turning requires too much power. When one side stops, the other side will start spinning much faster and loosing torque. Also uneven terrain will cause issues of the tank automatically turning instead of going over the bumps

Doctor D.S., Nice build so far. I am surprised you didn't build a brake system, using pedals... like a Farm Tractor, to free your hands to operate other equipment. That tank is going to be heavy when it's done; you may have to use a set of step-down gears to muliply the Torque from the 300cc engine enough to move it, without stalling once you engage the cluctch. (translated by google) Lijepa gradnja do sada. Iznenađen sam što niste izgradili kočioni sustav, koristeći papučice ... poput poljoprivrednog traktora, da biste oslobodili ruke za upravljanje drugom opremom. Taj će tenk biti težak kada završi; Možda ćete morati upotrijebiti skup zupčanika kako biste ojačavali zakretni moment iz 300ccm motora kako biste ga mogli pomicati, bez zastoja kad uključite kvaku (preveo Google)

Dobar video, jedan si mi od omiljenih jutjubera, voleo bih kad bi nekad napravio auto, npr da uzmes samo školjku od auta, a ti da stavljas delove, posebno bih to voleo da bude Yugo ili fića. Pozzz iz Srbije🇷🇸.

Ready for part 7! This tank is bad ass! Good job! And greetings from America! Good luck and keep building!

A suggestion, you should put some strips of metal to the tank treads so it has some digging in power instead of just riding on slicks.

You should add a clutch to disconnect the transmission so you can stop and go without being thrown off. Not to mention the tank will stop instead of the motor continuously trying to go forwards and might not actually stop. Not to mention you should have ripped out the full Automatic Braking System of 2 cars and put it in instead. It will make turning smoother instead of a constant jerking turn it will have. And lastly if you ignore everything else, just don't forget to secure the brake lines.

Hääähh...pushing the steering brakes instead of pulling it? I think this is counterintuitiv and is getting axhausting very quickly. Its not good, to rush the work, just to get the video finished every week....anyway.. i appreciate your effort on this vehicle build and the way you are showing it to your audience.... Nice work.... Greets from Germany..

You mention your “TURNER” regularly. I figure you are talking about a “Machinist”. You should give him a shout out by name. It seems he does good work for you. Just a thought. I am enjoying you build videos. I’m just wondering if you will mount a light machine gun, heavy machine gun or cannon on it when you finished. 🤣👍🏻🇺🇸

Great job I am very impressed I wish I could help you finish awesome job

Omiljeni si mi jutjuber samo tako nastavi !, nonstop mislim na tutorijale, auta, tenka, i ostalih stvari , najbolji si !

Napravi na tenku grn za snijeg da mozes cistit snijeg kad zapada.😁😂

hello , i have a question : can you make the "armor " of the tank ?

Yeah it’s all well and cool to steer but you still need a clutch, MUCH lower gearing, and a transmission. Otherwise it’ll be too fast with not enough power, will go forward as soon as you turn the engine off, and won’t have any capability of stopping or reversing.

You really need to remake the control handles. I would cut them weld them to go over the top of the control canisters and then angle up. That would take the handles from touching the seat and still allow free movement. Just my opinion...

Nice video bro.....I m aamir khan frm Pakistan islamabad ur video nd channel is god

You may need to have the drive “wheels” at the rear. That way under pressure the tracks won’t ripple under the machine. Like a dozer has

Очень не дурно для первого раза , очень много выйдет в процессе эксплуатации недоработок , а пока мой совет это реверс- редуктор ! С уважением из России ! И удачи в проэкте ! P.S. в следующий раз начни с тех задания перед постройкой аппарата .

I'm still watching this video

What happened to this tank my friend?If you have stopped the construction,could you,if you please, tell us what is happening?I really enjoyed watching the videos on the building of your tank! Alright?

this is cool the only thing im worried about is the rust on the frame

All I want to see ,is two pistel grip shifter handles on those two levers. Great job in a nice small shop 👍

I dont Speak Russian ....But I Love these Videos Comrade!!!

Well Done Now i know how your Clutch will work hopefully😏😏 One of your Barke Zylinders is very lose to the crankshaft Hopefully the crankshaft dont collide with the Zylinder Your Projekt is very interesting I look forward to the next Episode Yours Frank

Seat is too big... I think you have to use a go-kart one

I think that's the first time I've ever seen a brake system bled even before it was fitted !! I also wondered, did you weld the cast Iron caliper supports to that piece of box ? If so the cast will probably crack.

Ótimo projeto, parabéns aqui do Amazonas - Brasil...

I really like the brake setup. Looking good. Cannot wait to see it finished. :-)

Может чего-то не понял...муфта где, кпп, задняя??? А так прикольно!

Reverse the controls. Pull not push to turn.

Es geht voran. Sehr interessant.

Exceptional work. Maybe I would have moved the control levers to the sides of the seat. Until next time

Mislim da bi bilo bolje da si gas metnul na nogu. Ako je frka samo makneš nogu s gasa, a ovak, dok ga nađeš, povučeš ili gurneš, možda bu kasno. Gas i kuplung na noge, tak da su ti ruke slobodne za upravljanje i kočenje. Trebaju ti obje, nije to volan. I samo polako, imaš vremena.

It's very good to see your steering solution to shut up the cynics about the differential use. Well done.

Odlicno, samo mislim da si trebao ove rucke od kocnica stavit sa lijeve i desne strane sjedala, tako da kada se fino sjede budu pri ruci za uspravljanje, pozz!!

Wow, very great bro!

Front axle bearings are too weak and will break when the chains are on.

Idemo plako do 1 milion samo naprjed

looks like all your welds are top of frame only, I hope you weld the bottom too...

Few tips from dear experience , The brass throttle cable stop on the end will be a hinderance of wearing out on the small metal bolt from wiggling back and forth they ware out fast it will leave you sitting somewhere been there done that , , I`m really curious what your going to use to keep the tracks tight -A slip wheel like on the Caterpiller front idler will work great on this or TORSION bar Wheels somewhere on the track system ,, And don`t forget to stand this up on end or tip it over to weld all the joints underneath or they will fill with mud and water and rust or split constantly ,, The bolt holding the levers will be a bear when removing with rust ,, BUT GREAT JOB SO FAR !!

nice idea the braking system with a normal differential nice work man :) good work young man cheers from Montreal ,Canada :)

Cant wait to see next part

Frankenstajn💪pola od BMW-a pola od golfa😂

It's coming together man, nice work. I don't have any criticism, because I don't build tanks, so I wouldn't know what I was talking about anyhow. Keep up the good work, can't wait to see this beast roll.

Танк в 3 тонны а мотор от мопеда, браво

Love this build Friggin Awesome👍

Stari kombajni teski 5-6 tona plus bunker su imali veoma slican sistem koji je funkcionisao preko remena tako da tenkic ce da funkcionase sto posto .

Seguindo cada vídeo ansioso. Parabéns. Muito bom...

It`s some realy nice work of machinery skills, the thought and the carry out with the building using your one ideas, As I said Before Hat off, Stefan from Sweden.

Odličan video 👍👍

I am going to give this a shot...had a dictionary on my shelf surprisingly. volite svoje videozapise. nastavite s dobrim radom i sretno! Hope I got that right!

This thing is awesome, but I would have put the seat higher than the motor and lengthened the brake levers. And I hope you do some sheet metal work and do some aesthetic finish work

Thanks for sharing such wonderful content with your audience. It is very interesting stuff. I appreciate all the work put into it. Sincere thanks!

Kako ja nikad nisam vidio ovaj kanal

Very smart designs.Bravo !

Great video from Australia 🇦🇺

Better put a shield over the shaft or you may feel it when it lets go.

Doktore, mogo si da stavis cilindre od kvacila hidraulicnog mnogo manje komplikacija i lakse za zakacit nego te kocione. Cilindri od kvacila su mali i imaju samo jedan izlaz za crevo savrseno za tu tvoju namenu

Moc zajímavé.Jsem zvědavý, až nasadíš pásy a uděláš první projížďku.:)

And as well, get a transmission to go reverse and forward.

Félicitation de cette fabrication et bon courage à l'avenir

Od Golfa Trojke 🤣,imam golfa trojku ako treba nešto još od delova javi mi 🤣🤣🤣 Oni pre iz ratova tenkovi nisu nikakavi ovo je tenkk! Svaka čast na svom uloženom trudu! Odličan video

You are very smart boy !

Brasil love you PART 6 for PART 7,8,9,10,11,12,13,14,15,16,17,18,19,20 BRASIL, PORTUGUÊS, VOU CONTINUAR DANDO LINK EM TODAS CONTINUAÇÕES, VOCÊ E UM GÊNIO

Extra maszyna 👍

Ajd napravi titlove za one strance

Keep your shoe strings out of that drive shaft.

You push the right control forward and the tank turns right? This makes sense driving an old tractor and using the brakes to help steer, but anyone used to driving a skidsteer or zero turn mower would sure screw it up.

isnt it gonna rust up pretty bad he is putting alot of good hard work into it

BRAVO MAJSTORE !

Parabéns um mestre!!!

very cool your videos I am registered I live in Brazil

I would have mounted the throttle to one of the brake control levers. Better yet, use a motorcycle throttle twist grip.

Brate snimi kako ugraditi auto radio u imt 539

Without a clutch you can steer but as soon as you brake both sides and stop, the engine will stall.

Bardzo dobra robota. No tak.

Awesome work👍👍👍

Hoces li praviti oklop za tank?

I love to see such creativity you should have painted the frame and all raw parts so you could pass it on to a younger generation to inspire more to be this creative

I want to see it drive

I WANT VIDEOS FASTER AAAAAAAAA! sorry jk good work

Hallo Doctor D.S. I from Indonesia, I'am waiting part 7 from your videos, I like your videos👍

привет из России , город Миасс , Челябинская область . ты просто молодец , удачи ,жду когда доделаешь

Samo čekam da prodje jedva čekam da počne burazzzzz

Молодец! Привет из Беларуси!

Dude preparing for ww3

very interesting and simple to follow.. By the way what language is it?>

Thumbs-up from California

Está ficando muito top demais.

Should reverse the contols on the calipers so that when you push forward that side will continue forward.

I See one problem - cluc, how do you stop this machine when the engine is working?

Está ficando muito top esse seu projeto.

What engine did he use?

saludesd honduras estoy siguiendo estos videos muy buenossssss

As a tank mechanic i find some youer mistakes but any how you done well

svaka cast bit ce dobar tenk