Hornby TTS Sound Install - Is it as Easy as it sounds?

Рет қаралды 5,029

Күн бұрын

In this video I install a TTS Sound decoder from Hornby into one of their locos. It should be straightforward, shouldnt it? Find out!
If you want to buy this TTS decoer and try it out for yourself, click the following link:
www.amazon.co.uk/dp/B07N88T7C...

Пікірлер: 25

@MessingaboutwithModels 3 жыл бұрын

Has anyone fitted a TTS Sound to this loco before? Did I go wrong somewhere? Also, whats causing the stuttering when it ran fine on DC?

@mikepearce7346 3 жыл бұрын

Check out cv150, it changes the motor algorithm. I added a TTS sound decoder to my Class A4 (R3737), and I had to do some adjustments to the speaker fitting in the tender also - known issue Hornby TTS decoder speakers don't easily fit in DCC ready steam loco tenders.

@alanmargalan5921 3 жыл бұрын

Try Kampala Road he fixed a Class 31 TTS with the same problem Regards Alan

@MessingaboutwithModels 3 жыл бұрын

Thanks Mike, at least its good to know I'm not alone in finding them tricky to fit into locos they were designed for! A couple of people have suggested changing CV 150 to adjust the motor algorithm, it seems everything today is at the mercy of an algorithm!

@phil36310 2 жыл бұрын

Hi, I fitted TTS in 3 Maunsel S15's. Two J15's (very similar to your J36) Two K1's. One Large Prairie and one diesel. Some are strait forward and just need plug in. Others like the J15 even need part of the tender interior removed. Adjusting CV's is not a difficult task. Just do it 'on the main' and you observe & hear the result of changes immediately. Every motor reacts differently even when you use 'high end ' decoders like ESU or Zimo. But to my experience the TTS do well and with some minor 'tweaking' they perform as good as high end decoders without the endless number of CV's these come with. For the price they are just fine. A decoder that is also a good choice is the Soundtraxx Econami 200 UK sounds. Double price - very good quality. And after all DIY is part of this wonderful hobby ! And first came the loco - then the sound. Success !

@MessingaboutwithModels 2 жыл бұрын

Thanks - I've used the Econami on my Bachmann 4MT - check out the video here and see what you think? kzfaq.info/get/bejne/jdimdM6QvcjSd6s.html

@jakerichards1117 3 жыл бұрын

Great video - thanks for showing how to do it

@MessingaboutwithModels 3 жыл бұрын

It's was actually quite tricky. If I was doing it again I'd definitely swap the speaker out for a different one.

@StationBBLT 9 ай бұрын

Lovely!!!

@jj8995 2 жыл бұрын

Thanks mate I will give Peter's spares a try

@MessingaboutwithModels 2 жыл бұрын

Let us know how it turns out!

@jj8995 2 жыл бұрын

Any ideas where I can get the wire with the white plug on it I've broken mine I've looked everywhere thanks that's a good video very helpful

@MessingaboutwithModels 2 жыл бұрын

I would suggest Peters Spares - but there are lots of similar plugs/sockets on ebay too.

@janeresting9667 2 жыл бұрын

The Steam TTS decoders seem to be very tricky compare to the diesels!

@MessingaboutwithModels 2 жыл бұрын

I hope not! I've got one I'm putting in my J83 and another which was originally going into the Standard 4MT, but which now I'm going to try in the Ivatt 2MT 2-6-0 that I've got.

@alanmargalan5921 3 жыл бұрын

Have a look at Kampala Road he did a fix on a class 31 with the same problem i am sure it's just a few minor changes to the CV's hope this helps Alan

@MessingaboutwithModels 3 жыл бұрын

Thanks Alan, I'll do that! Dont think I know that channel, so hopefully found a new youtuber to follow!

@alanmargalan5921 3 жыл бұрын

Hi the cv's you need to change are cv 151 set to value of 255, then cv 152 to 01 you should see some improvement make a note of the standard settings before you start, good luck Regards Alan

@dwaynejohnson4892 3 жыл бұрын

Where do you get those loco mats? I’ve installed the same sound decoder and no sound. Do I need to setup the sound or is it ore loaded?

@MessingaboutwithModels 3 жыл бұрын

The sound is pre-loaded, and it should work straight out of the box. F1 will switch it on, then you can use the other functions as and when required (eg whistles, coal shovelling etc).

@michaelbenton4117 2 жыл бұрын

Hi, I have tried fitting a decoder to two west country class loco , I m having the same problem. Out comes the file. Thanks for your video. , Yes I have the same problem with on engine , ok in dc but stutters in dcc when coder is in. Have tried a second decoder in the same engine and still stutters. But the second decoder works okay in the other loco.

@MessingaboutwithModels 2 жыл бұрын

Check out my other video on the sound fitted J36 - it might be that some CV changes will help improve the running.

@michaelbenton4117 2 жыл бұрын

@@MessingaboutwithModels I've looked at your video's and made nots thank you for replying

@brucewoods9377 2 жыл бұрын

Hornby, in my experience never produced a tender or loco that would accept easily their ridiculous speaker. I have always replaced the speaker with sugar cube varieties

@MessingaboutwithModels 2 жыл бұрын

Yes, I agree. I just find it frustrating that they provide something that doesn't work in what they intended it for.