This is why i service my ebike yearly.... If you spend the money on a bike spend the time to look after it also dont abuse it......
@EbikeRepairs7 ай бұрын
A great idea!
@jjung200519 күн бұрын
I believe regular scheduled maintenance is the key like everything else. Did you get it used? That thing went through hell!
@EbikeRepairs12 күн бұрын
I got it jet washed sadly 🤣🤣
@markj6984 Жыл бұрын
is the hall sensor quick connect bigger than the 500watt version? i have a 500 watt version and was wondering if you need a special ext to connect it to the exsisting harness from controller
@EbikeRepairs Жыл бұрын
750w uses the large BAFANG 'big 9' type connector. 250w uses JULET 9 pin waterproof connector. Not sure about the 500w one. Adapters might be available!
@markj6984 Жыл бұрын
@@EbikeRepairs thanks brother i figured it out. i had to buy the large sized wiring harness not easy to locate.
@dustsmoke10 ай бұрын
It looks like somebody did that stupid idea where they inject their 750W motor with something like mineral oil to "help' with cooling. The problem is these things aren't air tight so all that crap almost immediately all leaks out and creates a nice sticky surface for any sort of dirt and grime to stick to
@EbikeRepairs10 ай бұрын
I believe this one got jet washed and left full of water!
@jonasmeier4177 ай бұрын
This might prevent from this/make it easier: - Open new motor, grease it, put rust protection color on it - Check that thru cable no water is coming inside motor - Buy a second motor, so you can replace later what's needed
@EbikeRepairs7 ай бұрын
Very good ideas! This motor was really beyond cost effective saving.
@LaLaLand.Germany7 ай бұрын
Good stuff but how would You go about without slide hammer puller? Could I just whack them bearings from behind since there´s space between? I have a similar motor and plan to service it. How tight do You pull them screws in the flange that holds the cassette sprocket, I always like to use a torque wrench. Can You put a number on that? Yeah, it ain´t rocket science but I very much like my torque numbers as I HATE extracting broken bolts. So I better not tear them in the first place. Thank You Buddy, keep the good stuff coming, I just have a tiny shop in an attic but try to estabilsh myself as backyard mechanic by watching stuff like this and trying it out on my own devices first before I advertise like a brake service. It really is fun to me and the happy smiles I get when a job is well done makes it all worthwhile.
@EbikeRepairs7 ай бұрын
Hiya thanks for the nice feedback! Whack them out! Removal is removal... Just don't damage the bearing surface of the motor. Torque wise, there's no official torque spec, but 10-15nm should do fine, they really don't need to be insanely tight, they're only m4 size bolts. And the design is weak at the shoulder and head can snap off. Good luck!
@utubeape Жыл бұрын
its no wonder water gets in there is no gasket or any seal between the motor casing parts, maybe a smear of Plumber Mait might help?
@EbikeRepairs Жыл бұрын
yeah it sat outside for a long time i think! months of rain...
@utubeape Жыл бұрын
@@EbikeRepairs its going to get wet riding when it rains, so the manufacturers should think of it in the first place, a rubber gasket isnt rocket science
@EbikeRepairs Жыл бұрын
Agreed.
@ivansalazar66846 ай бұрын
Help!!! My electric bicycle started displaying error 24, all the wiring is well connected and in perfect condition. When im activate the accelerator the engine only turns a couple of times, and makes a small noise. My engine no longer works? It only has 1500 miles.
@EbikeRepairs5 ай бұрын
Sounds like perhaps a halls sensor problem - error codes are manufacture specific... Are you local?
@fraserthomson5766 Жыл бұрын
Have a similar problem with my inner bearings, anyone know what size these are?
@EbikeRepairs11 ай бұрын
Inner I'm not sure sorry!
@thirtysixforfun10 ай бұрын
Anyone know if they make stainless steel teeth wheels for the motor as an upgrade?
@EbikeRepairs9 ай бұрын
I'm sure they do, check AliExpress
@JeepingNomads Жыл бұрын
How did you get the clutch assembly off?
@EbikeRepairs Жыл бұрын
3 leg puller is usually needed for that one bud - available on Amazon/local hardware store. You can lever it off with 2 screwdrivers, but are likely to damage/scratch things!
@JeepingNomads Жыл бұрын
@@EbikeRepairs I was able to get it off but it looks like the inside of the motor is completely seized up. The bike fell into salt water at the beach. It was a quick dip but it looks like that's all it took. I guess I'll be shopping for a new motor.
@gauravjoshi9183 Жыл бұрын
Hi what's the spoke size in that rim?
@EbikeRepairs Жыл бұрын
Sorry dude the bike has gone now I'm not sure!
@sonythabeast10 ай бұрын
How many miles did you ride for the motor turn into rust ?
@EbikeRepairs9 ай бұрын
I didn't, I bought the bike like this sadly
@cesus351 Жыл бұрын
Hi - what size rim and tire is this?
@EbikeRepairs Жыл бұрын
20 x 4 inch :)
@houssdedjey8291 Жыл бұрын
Hi . It's a tire Michelin of moto ?
@EbikeRepairs Жыл бұрын
I'm not sure! sorry.
@judecapone76518 ай бұрын
Looks to me like that thing was underwater for quite some time!
@EbikeRepairs8 ай бұрын
It was full of water for months!
@bruku007 Жыл бұрын
Yeah, My Bufang 500w "Frozen " with 》100hrs. No Gasket .
@EbikeRepairs11 ай бұрын
wow! is it as bad as this one?
@user-zx9yy6lu9p6 ай бұрын
How many magnets in a bafang rear hub motor
@EbikeRepairs6 ай бұрын
The numbers differ per motor, it depends which one you have - check on endless sphere, there's loads of good info there 👍
@user-zx9yy6lu9p4 ай бұрын
@@EbikeRepairs thank you
@user-zx9yy6lu9p4 ай бұрын
BAFANG G062 Fat Tire 48V750W Rear Hub Screw Freewheel Motor THIS WIULL THOUGH IM SURE
@user-zx9yy6lu9p4 ай бұрын
Will this motor fit into a 250watt bagang hub
@EbikeRepairs4 ай бұрын
If it's a g060 size case yes it should!
@user-zx9yy6lu9p4 ай бұрын
@@EbikeRepairs OK MINE is RM G062 SO I GUESS NOT.
@user-zx9yy6lu9p28 күн бұрын
Well i just received my 750watt Bafang rear hub motor,and yes it fits into my 250watt casing very happy