Cheers David. I know a lot of people watch on their Mobiles, but I make sure 99% of my stuff is uploaded in 4K, nothing worse than pixelated slow mos!

No problem dude

Thanks Mark, I watch loads of others videos but quite often forget to comment, or have the video playing on my TV.... Hope you had a good Xmas and NY, lots more Tamiya's for 2020 I hope! My mate wants that Quattro you are building.... I keep trying to get him to buy one!

@@TomleyRC All good here thanks Phil! Yeah I watch a lot on the TV late at night when the missus has gone to bed! Hopefully some new Tamiya kits for me this year, not sure which at the moment. Yeah, the Quattro A2 is a little beauty - trying to muster the courage to start applying those darn stickers! :-)

Oh...the wonderful decals haha. Good luck!

Yes, I worked it out after doing the video.... I will do an with and without comparison

Yes, going to test them soon...

Sounds cool! They are nice trucks

Great

Mine keeps on cutting out do any of you know a fix?

@@Mouse-dd7dn Try another BATTERY

@@ianmangham4570 I got it like 2 days ago but it takes 30 mins for it to run out and like 5 hours for it to charge is that normal?

Cheers dude. Hope you stick around 👍

Yes, realised after doing the video

Cheers mate 😎👍

Thanks dude

Yes, it's also the same as the FY03H. Good tip about the switch 👍

Yes, nothing different other than the name and colour

Yes, black looks good doesn't it

In case you have not already done this, try adjusting the steering trim knob on the transmitter.

And you dude

Yes, I finally worked it out after filming. They are very wide!

Cheers dude.....Strange it has no on/off switch! its not under the body is it?

No dude you just switch on the remote on off it goes iv looked everywhere 😂😂😂😂

I'm sure there is a bind button on the transmitter?

I looked but could not find one I'll look again

Thanks dude

Probably ok in clean water.... but not mud

Yes, these make good rock bouncers

oh.. move the steering ball to the inside hole of the servo arm, doesn't limit steering too much, gives steering lots more torque tho.

@@modelnutty6503 It's not the same as the wltoys...The gears Pitch are different, dogbones..ect. i got bunch of vithuck for $40-ea years ago and a fy03 for $46...converted them to brushless 2845 3300kv $12.. Might as will get a brushless..it cost the same to replace the 390. The WLTOYs has 550 motor. 60a esc $15, MG servo $7, rx$7..a 2200 mah 35C will make it do a back flip from a stand still.Pop wheelies on command.it's do 45-50 Mph..EASY...just get oil shocks $12. lower the springs, lower the battery tray....14mm hex 1/10 wheels/off road wheels are only $12 p/set. hex extension are only $7 p set. metal drive line are only $7... you only need the rear. I just mounted the wheels and tires from the KT-12...hex extensions. I have them all different configurations and One stock. You can build a little 50mph beast for $120 if you know what ya doing. Then again i've only paid $115-$130 for all my 1/10 brushless trucks.lol It;s not a big deal...I get use 1/8 rollers for $100.slap in 4076-4092 120a-150A ($80-$100)..make those go 50mph too. Lipo are also getting cheaper. You can get 2s 5000 mah 50C for $12. it's the 5000mah @ 50C...it's like running a 3s 25.lol Even that out runner is little....( 2217) you can get a 2220 2700Kv for $7, now. Out runner ARE NOT WATER PROOF.

No waterproof... but a bit of water is usually ok

Yes, I'll maybe get some once the weather gets better.

I've just seen you can buy the complete FY03H body cage and panels in red for £16. No brainer 😄👍👍

£16! Thats a bargain! Although not as much of a bargain as the 12428!

Yes, worked it out in the end anyway. Merry Christmas dude

The 12428 is pretty much the same, but I think the build quality of these is a little better

@@TomleyRC thanks, from everything I've seen these are pretty much a fy03 copy.

Cheers dude.... luckily because they just rebrand stuff, you just have to find what the original car was.

haha...it has crossed my mind 😎

And then sell it for $700 less ! Because that's how much it was overpriced in the first place

Mine keeps on cutting out do any of you know a fix?

Yes, they are fun, if you can keep them on their wheels! haha

Yes, same set up 👍

😅

Jumping a Great White Shark next week, just fitting the 200mph motor first 😎🤘

LMAO, Skate Park trashing, ROFLMAO

Mine keeps on cutting out do any of you know a fix?

@@Mouse-dd7dn try n find an old WLToys esc if you’ve parts left from brushless conversions?? N drop it in? 👍

@@rcandy5119 ok thank you

Most 'American Brands' are made in China... it's just a label ;)

👍 if you haven’t got one you can get a cheap one for less than a tenner from the usual places as I’ve just realised it’s brushless 🤣

Yes, makes it a bit easier for inexperienced drivers

Not sure what electronics the 10428B comes with, but WLtoys is usually combined

I'd really like to put crossfire in so be great separate

Quite possibly, I've yet to see an Eachine RC Car that is there own product.

Mine keeps on cutting out do any of you know a fix?

Yes, I have some Box Googles from them, good price and good quality... just never seen a ground vehicle that is not just another make rebadged

It's 'splash' proof.... but you saw how much water I went through, and it still works

Yes, you are probably correct. 😎

Yes, I realised that after doing the video. Might try them

Maybe the mesh is a little tight?

@@TomleyRC I'll check

It’s pretty good yes! Rolls over quite a bit if you are not careful

@@TomleyRC Thank You

Traxxas will probably never stand a chance against a China based company, they don't conform to the usual Copyright/Trademark rules!

Yes very similar.

Seems to be... although don't recommend submerging it like in this video..., it will eventually damage it

Yeah 😎🤟

@@TomleyRC 👍👍

@@TomleyRC they will stop so many rollovers lol

Will do

I'll be giving them a go soon, might do a with vs without

Yes, it a bit of a 'roller'

True it rolls at high speed in the corners. But if the driver has got some good throttle control skills and not just operate the throttle trigger like it was an on/off switch (i.e. zero throttle/full throttle) this can easily be avoided by reducing (some) throttle in the turns, it also makes for a much much nicer run with almost zero flips. It is an aquired skill which comes with patience and practice. After all, that is why proportional speed controllers were invented for :-)

Very true...

Actually in china there are business model like this is, there's one design company, they do design and probably has the factory to produce it, and then any clients/brands can order and customize the color, branding, etc..

Cheers dude.... Happy New Year. *can't see that video

i will pull it up

try #philison🔥had to repost

I wouldn't worry about the 'Kev' drama, he does it for attention. I've been testing and reviewing RC's longer than him, I often drop them in slow mo to show the suspension. I must admit though, after editing and uploading this one I did notice that the fast cutting of the tie wraps mixed with the dropping it on the table was pretty similar... to much work to change it and re upload though. Anyway, cheers for watching..... "SUBSCRIBE" . haha

K

Tomley RC you have been testing RC’s longer 😂🤣😂🤣 what a petty claim to fame hahahahaha you are boring as bat shit and your monotone voice is a snooze fest you are a passive aggressive douche like a 12 year old, grow the fuck up and stop promoting the shit Chinese products you quite clearly sell, sell out.

mattysixx Kevs just reviewed this RC...go give him some shit as well 😂...or is it ok because he gets over excited all the time and is not boring like me? Asking for a friend?

mattysixx the more I watch Kevin the more he looks like an idiot

Yes, it certainly is...just re branded

I don't copy Kev..... well, apart from we both review cheap RC's. Seen his mini Grave Digger?.... go check out a video I made months ago and then tell me I'm copying him haha

Ok

Sorry