How Do You Replace A Balance Staff In A Watch?

How Do You Replace A Balance Staff In A Watch? - Vintage Watch Repair

Рет қаралды 19,120

Күн бұрын

A very common issue with vintage watches, especially those without shock protection is a broken balance staff, or an excessively worn one. In this specific case we look at removing a balance staff with a bent pivot. We then fit the new balance staff, and poise the balance ready for installation in the watch. I hope it helps to provide a set by step guide for your instruction.
I apologize for my hand being in the way for a few shots. If you have enjoyed this video please like and subscribe to the channel. You can also check out my website www.precisionhorology.com and my Instagram @precision_horology.

Пікірлер: 44

@tk_customwoodworks 5 ай бұрын

I've watched endless hours of watch repair on KZfaq, this is the most comprehensive explanation of replacing a balance staff that I've seen. Including roller removal.

@PrecisionHorology 4 ай бұрын

Thank you, I really appreciate your feedback.

@quaarjet Жыл бұрын

Nicely done! Never thought to use the Horia tool for balance staff removal. Keep up the good work and thanks for sharing 'secrets'!

@IShootWatches Жыл бұрын

Thanks for this video! This is the best video I've seen about changing a balance staff. I've been gathering the tools to try it myself with the help of this video!

@PrecisionHorology Жыл бұрын

Glad to hear I could be of help! I hope it goes well.

@ChoocherFronz 2 жыл бұрын

Thanks Ashton, another great vid. Thanks for showing how to deal with a loose roller table. Cheers.

@Distoideas Жыл бұрын

Thank you very much, got lots information of staking tips. Great video.

@marekeos 2 жыл бұрын

Excellent video. Very informative. Thanks for posting this! Subscribed.

@gwsjr1 Жыл бұрын

I use the same roller removal tool, it works well just by sliding the wheel with the roller still attached the balance staff. No need to squeeze the tool as the ledge that fits between the wheel and roller is tapered so it essentially acts like a wedge to separate the two parts.

@hendlers7071 4 ай бұрын

A great video - Thanks

@bismillakhanm3917 11 ай бұрын

, pain liever moment

@hyselwatchandclockrepair1874 7 ай бұрын

Thank you for sharing your experience on this excellent video.

@PrecisionHorology 7 ай бұрын

Your most welcome, happy to share the knowledge around!

@itzhaccroitoru4082 3 ай бұрын

Thanks for this video!

@boydsargeant7496 Жыл бұрын

Thanks Ashton, shame your hand was often in the way, but great commentary as ever!

@VWatchie 2 жыл бұрын

Very informative. Thanks!

@PrecisionHorology 2 жыл бұрын

You’re welcome! Glad you enjoyed it.

@RandomRestore 2 жыл бұрын

Thank you, what a great informativ video!!! You got a sub 😊👍 now i start a video marathon and watch all your videos. Best regards Danni 🇩🇰

@peterhawley6273 Жыл бұрын

Very good video 👍🏻

@alanmckinnon6791 2 жыл бұрын

Great video with nice voiceover. Subbed

@khronosbest9448 Жыл бұрын

Excellent thank you.

@OpenWoodShop 4 ай бұрын

I feel like I know this procedure like the back of your hand.

@PrecisionHorology 3 ай бұрын

Original.

@Watcheyes Жыл бұрын

This was great, many thanks for the tips you shared, priceless. What Horia sortment of presses would you recommend? There is a set of 12 presses (Horia assortment no 3) and 6 anvils. The presses ranges from 70 to 180 (guess it's 0,7 to 1,80 mm). Thank you.

@kiteboardkid Жыл бұрын

Beautiful to see. Quick question Ashton... After watching this I'm looking to purchase a Horia Jewelling tool, I note there is a 3mm and 4mm spindle version does it make a difference which I buy? Thank you and keep up the great content.

@Timesradical Жыл бұрын

Nice

@etebol 2 жыл бұрын

Thanks for the video and for sharing. Now I thought that the balance screws could be turned IN or OUT in order to alter the gravitational center, was that wrong?

@PrecisionHorology Жыл бұрын

You aren't wrong, but also not completely correct. There are screws that can be moved in and out, but only certain screws. Most of the crews on the balance are fixed and are just there for weight. You always need to poise a balance but removing or adding weight, after a staff is changed.

@kenhelix4494 2 жыл бұрын

Good informative video, giving me confidence to re-rivet my own. Pity about the hand which obstructed the camera at the wrong moment in that you were turning the stake between hits. Henry B Fried or Archie B Perkins said to use a brass headed hammer for stake work, so I always do - can you comment on that?

@PrecisionHorology Жыл бұрын

Honestly, not really. I'm not sure why a brass Hamer would be better to be honest. Could it be a weight thing?

@johnhannon 8 ай бұрын

@@PrecisionHorology From what I have read, a brass hammer has less chance of damaging the end of the punch where you strike it. The end of the punch will get mushroomed over time and it will be hard to insert the punch in the inverted position (used as a stump).

@PrecisionHorology 7 ай бұрын

I've never seen any damage to my punches, they seem to be just fine. But thanks for sharing that. @@johnhannon

@alexanderkamerbeek9693 Жыл бұрын

What pusher did you use for this on the horia? I only have the pumps but they don't have holes in them.

@PrecisionHorology Жыл бұрын

What does your hora have as the bottom stakes? You use those in the top. The size of stake is dependant on the size of the balance staff.

@alexanderkamerbeek9693 Жыл бұрын

@@PrecisionHorology ah you used a bottom anvil as a pusher in the top do I understand correctly? Thanks in advance

@torenoomi3584 2 жыл бұрын

So you dont cut the rivet on the lathe first, before you press the staff out with the Horia?

@PrecisionHorology 2 жыл бұрын

No, you either cut out in a lathe or press out.

@raymond15101984 5 ай бұрын

You should cut the rivet or use a a special tool called molfres to prevent the balance wheel hole decentering

@Peppermint1 5 ай бұрын

Is this the most common problem with mechanical watches that won't run ? I'm looking on Ebay and wonder what is the reason many vintage wind-up watches won't run.

@PrecisionHorology 4 ай бұрын

It's one of the problems, and when it comes to watches before shock protection it can very likely be the culprit. Many watches won't run though just due to the fact that they haven't been serviced and all the old oil is gummed up.

@Peppermint1 4 ай бұрын

@@PrecisionHorology Thanks you. Assuming a vintage mechanical watch is only gummed up, how long of a job is to have it cleaned by a professional ? Just trying to figure out the costs. Assuming a standard wind-up model.

@PrecisionHorology 4 ай бұрын

@Peppermint1 entirely depends on a number of factors. The watch in question, etc. too many factors to say.

@nevinsummers7099 Жыл бұрын

Well, unfortunately, I missed a lot of the critical parts of this procedure, but I am now very familiar with the back side of your left hand.

@PrecisionHorology Жыл бұрын

I tried to keep my hand to a minimum, but I am only an amateur videographer. If you can’t fill in the blanks of when I’m turning the work piece or hitting a stake with a hammer, I’d suggest a new hobby. Watchmaking may not be for you…