Bless you, Indian KZfaq tutorial guys. Absolutely no-nonsense, clear, calm, and informative. India's best export in the digital age.
@rubenrubinos9825 жыл бұрын
Thank You For Uploading This Video, Helped me to reassemble my spray bottle. No need to run to the store and buy a new one when this one was repairable and works great once again!
@RondaHedges5 жыл бұрын
Thank you for this rather comprehensive tutorial. It has helped me repair 3 sprayers.
@mathewandmarleny6 жыл бұрын
Totally helped me put back together the empty spray bottle I bought at the store the other day that just feel apart. Thanks!
@georgekahn331310 ай бұрын
Thank you Mr. Singh, your tutorial showed me how to successfully put my sprayer back together. 👍. 🙏
@q7winq7 Жыл бұрын
12-1-2022 - - - - Here's the short version: Tube (straw) immersed into liquid. Squeeze trigger compresses a spring against the trigger and contents of cylinder are compressed with a piston. Compressed contents flow past a ball that is pressed against a gasket (o-ring) by spring. Compressed contents ejected through small port in nozzle to the outside air. After trigger released, the spring re-seats the ball against the o-ring blocking reverse flow. Trigger is released and trigger spring forces piston back creating vacuum in the straw sucking more water into the compression chamber of piston. - - - - There, fixed it for you. The sprayer shown in this video doesn't have a spring/ball/o-ring assembly in it. The sprayer in the video is a more simple mechanism. Better sprayers have the ball/spring/o-ring assembly style. Good luck. Don't use bleach in sprayers without rinsing out with water afterwards to wash bleach off of the internal parts - or they will dissolve/rot and leak, making sprayer into junk. (Cheers - ex-engineer).
@mgsriramiyer6 жыл бұрын
Simple, no-nonsense explanation. Good work
@Shawshank086 жыл бұрын
Thank you ! Appreciate it :)
@diwakarprasad20573 жыл бұрын
@@Shawshank08 my contacts no. 9899375937
@diwakarprasad20573 жыл бұрын
I'm interested in trigger spray manufacturers plant
@spicer41282 Жыл бұрын
Best video found after viewing 6 others which was just ok. This one breakdown of parts and clear explanations sets it apart head above the rest! Great work! Too bad you stopped😢 making others.
@tintinxyz4 жыл бұрын
A small suggestion.. maybe if u used colored water the flow would have been more visible and the mechanism would have been more appreciable..
@LuxeLifeVibes6323 жыл бұрын
BRO, Do more videos. This was an amazing video.
@Shawshank083 жыл бұрын
Thank you! Appreciate your kind words!
@rajasreeg33056 жыл бұрын
Very good and simplified scientific explanation..Thanks.
@Dlktar2 жыл бұрын
Please continue doing these amazing demonstrations
@apurvaprajapati99393 жыл бұрын
Thanks for the video! It's knowledge. The nozzle is also an interesting part. You could show that in more detail.
@SohilShah_Melodyman6 жыл бұрын
Nice explanation! Thanks.
@Yash-em2qm4 жыл бұрын
In short .Bernoulli theorem , Pressure volume relation is the key . Good video..
@rick1891 Жыл бұрын
Great video! Thanks for your explanation.
@Tech-Ing6 жыл бұрын
Placed in a closed bottle, Does it create vacuum or is there air incoming to the bottle for replacing the ejected liquid? (I don't think it creates vacuum, else, at some moment, it would be almost impossible to continue ejecting liquid).
@diamondaforce2 жыл бұрын
I’m not 100% sure but I think that if you mean inside the little thing where the spring is, when it empty’s out then since there is empty space the water tries balancing so it goes up. Again I’m not 100% sure
@lpaprocki3 ай бұрын
Thank you so much for this!
@Cryslr3Hun Жыл бұрын
Hello I really enjoyed watching the mechanics of how the sprayer works. Question, If I have a sprayer that leaks from the nozzle when spraying where would the leak or water be coming from ? Thank You
@fordvockell Жыл бұрын
Thanks so much for helping me with a school assignment
@saibhargavi57214 жыл бұрын
Thank u so much today spray bottle is working after following your video
@townley1017 Жыл бұрын
Great video 👍 just what I wanted
@narasimhachopparapu45343 жыл бұрын
Thank you for the video. how liquid enters to top of piston initially?
@techworld55175 жыл бұрын
I like the teaching stick 😂
@kimmywhitt61125 жыл бұрын
Thank you!!
@a1m33frank2 жыл бұрын
I have one with a ballbearing and soft washer and a small piece of plastic. I bought the amber glass spray bottle from Grove. Could I get assistance with putting this back together? The video was very helpful. Thank you for sharing.
@Edgar4T007 Жыл бұрын
Great video 👍
@recommendedforyou79577 жыл бұрын
well explained. thanks!
@Shawshank086 жыл бұрын
Recommended for you Thank you :) appreciate it.
@g0d5m15t4k32 жыл бұрын
Thank you!
@srikarreddy75913 жыл бұрын
Did you forget to explain about NRV, which you mentioned in the beginning?
@kendallhouse74976 жыл бұрын
So the nozzle does not necessarily need to be perpendicular to the vertical tube. It could be rearranged to spray upward?
@harshstudy488 Жыл бұрын
Amazing thankyou
@kritikamatolia12135 жыл бұрын
I'm trying to fix a spray, there is a small glass bead / ball and not sure where it goes in the entire apparatus, could you help?
@mokshilshah29273 жыл бұрын
Great explanation 👍👍
@rohitsharma-il8xn4 жыл бұрын
Good information just working old spary bottle works like new
@generalawareness101 Жыл бұрын
Is there a way to connect an air pump to any of those pieces so the air that comes out is as fine as the water spray mist was?
@mamtapandey35473 жыл бұрын
Well explained👍👍👌🏻
@sujalsaffire58964 жыл бұрын
Thanks so much 💎❤💎
@N.S.Sdanceclub3 жыл бұрын
Thanks sir helped me alot
@sarthaksingh65953 жыл бұрын
Thank you for this informative insight
@Shawshank083 жыл бұрын
Glad you found it useful!
@masoomakhanam81463 жыл бұрын
Good explanation 👍🏻👍🏻👍🏻
@user-zh6ud6kn6r2 жыл бұрын
As a sprayer I can confirm that we really work like that
@DarshanSenTheComposer6 жыл бұрын
4:50-demonetised XD
@masoodatif2 ай бұрын
i fixed my sprayer. thank you
@ScienceVideo-zf8od6 ай бұрын
Thankyou🎉❤
@redredwine12774 жыл бұрын
Thank you for info 🌸🌼🌺
@akshayaapspk49403 жыл бұрын
Thank you😊😊
@Andi-fk8vs2 жыл бұрын
Omg this is the only video that WORKED
@chromospark30413 жыл бұрын
how to get the small ball back in its place.....ball valve such that it works......i think mine got displaced
@zenobiakhan5665 Жыл бұрын
I've lost tigger bottle nosle, can i use any nosel??
@lilfiremonster39034 жыл бұрын
Can you make this in any other material besides plastic?
@Train1153 жыл бұрын
Very good video! I learned so much from this, only suggestion I have is to work to improve the camera work a little.
@diamondaforce2 жыл бұрын
Thank you for the video. Could you please explain why the water moves up the pipe though. Is it because there’s empty space in the thing and it tries balancing out? Would liquid be able to do that? And why doesn’t the air escape right away without you spraying. Does the nozzle also open up? I understand if you don’t see this and don’t answer but if anyone has answers please do share
@sarmankumar592 жыл бұрын
I might be wrong, but giving a try. When the presses the plunger/lever/whatever, it pushes the piston in upward direction. By pushing the piston upwards, we increase the pressure and decreases the volume in cylinder. As the one end of cylinder is connected to nozzle, whatever matter (liquid water or air ) is in cylinder runs to nozzle. In nozzle, kinetic energy thus velocity of fluid is increased on the expense of pressure. When we leave the plunger, piston runs back to it's normal position, thus increasing volume and decreases pressure in cylinder fall below the pressure of fluid in the container ( bottle ). As the downward end of cylinder is connected to the bottle through pipe, due to differences in pressure, fluid start moving from high pressure area to low pressure area. Thus we have fluid/water in cylinder.
@samric20002 жыл бұрын
thank you
@ummifatihah73942 жыл бұрын
Where to buy all this
@safetyalways7788 Жыл бұрын
I just bought spray bottle but water is not coming out. Do I need to pierce the nozzle or what?
@camelCased Жыл бұрын
I have another problem. I had a pesticide in the bottle, so I wanted to wash it out. I screwed off the nuzzle, and then while rinsing the bottle, that small inner plastic thingie of the nozzle flew out. I put it back and screwed the cap on but now when I spray, I don't get a mist but just a tiny stream out. Ok, it's "good enough", but it doesn't cover a wide surface anymore, because it sprays to a single point 😀 I tried to turn the cap both ways to adjust but it did not get the mist back. Not sure, what happened - maybe there was one more plastic piece inside that plastic thingie, and I lost it. Wondering if I can find something to replace it.
@Betty99715 жыл бұрын
That was awesome!
@Shawshank085 жыл бұрын
thank you! this video was the outcome of a boring weekend. Never thought so many people would appreciate it.
@karthiksukumaran856 жыл бұрын
that was very good explanation
@Shawshank086 жыл бұрын
Karthik Sukumaran Glad you liked it :)
@mayurmalwatkar97543 жыл бұрын
Very good explained👌👌👌
@Shawshank083 жыл бұрын
Thanks! Glad you like it!
@andrickriverapizarro7213 жыл бұрын
What is the equation that describes or governs the transformation of potential energy into kinetic?
@guest20073 жыл бұрын
1 mar 2021 9:53 am est(utc-5): law-of-conservation-energy/law-of-energy-eternality : kinetic-energy = potential-energy. 1/2 x mass x (speed)^2 = mass x gravity-acceleration-speed x altitude ?
@ironmen8085 жыл бұрын
Can you help design a spray bottle
@shubh.jain19904 жыл бұрын
hello, my spray bottle is working opposite...i dont know what happend to it ? can we solve this ?
@blueandbanana4 жыл бұрын
Can u pls show us how to take it apart, piece by piece?
@wenaavendano47492 жыл бұрын
Please share your new video how to fix hi pressure bottle. spray
@tintinxyz4 жыл бұрын
Also pls spare a mention about the valves.. These are very important in keeping the liquid from flowing back. Also when the piston expands the cylinder, the liquid is brought into cylinder
@myjourney77132 жыл бұрын
Exactly related to this I have a doubt. When cylinder expads after spraying water, what is stopping from air to get sucked in due to low pressure instead of water getting sucked up? A value in nozzle?
@Dalziel452 жыл бұрын
@@myjourney7713 A valid concern indeed!
@cend23624 ай бұрын
the nozzle is one way (air cant come in when trigger is released) because its similar to, for example, a vacuum hose sucking a big object larger than the hose mouth. but in this example, the big object is something inside the nozzle. @@myjourney7713
@TheMsOfficialMe2 жыл бұрын
Can you explain how the flairsol works
@atikmansoori13 жыл бұрын
Sir could you transform this nozzle into automatic spray
@sathyasathya28984 жыл бұрын
super
@pzk50993 жыл бұрын
Please let me know how have u opened the parts
@pzk50993 жыл бұрын
I m not able to separate cap and the piston
@amantedecapaldi40373 жыл бұрын
A continuation of video should be making this system a very crude one with readily available stuff around our house .. what say?
@Cambria3996 жыл бұрын
This could be good but you did not mention the valves. the most imporatant part? maybe. Unless I did not hear you perhaps...does it have check valves or some means to move in one direction? I like the idea of doing this video thank you. also the sound was not easy to understand. Not being mean... just interested in this simple machine.
@Shawshank086 жыл бұрын
Cambria399 My apologies. I forgot to explain the function of valves. And as for the sound, may be it's my accent or the white noise in background. I'll try to improve in my next video.
@Cambria3996 жыл бұрын
Cheers mate, I gave thumbs up :)
@bhumikadugad40214 жыл бұрын
@@Shawshank08 could you explain the valves function right now through words itself , i need to understand that urgently
@niranjanbhagat94832 ай бұрын
Radhe Vallabh Shree Hari Vansh❤
@patronam93962 жыл бұрын
Finally found the right video
@jaisharma80564 жыл бұрын
Great great great bro
@stone87143 жыл бұрын
What would humanity do without Indian youtube?
@adiliraliyev58824 жыл бұрын
Cut it in half? To see wts inside.
@yadvendrarsingh94174 жыл бұрын
R u from India
@Zoranurai13 Жыл бұрын
i should be studying but i'm looking up how a spray bottle works...
@simranjoharle42206 жыл бұрын
How does the water rise up the very first time?
@thybiscuit6 жыл бұрын
venturi effect
@ib56615 жыл бұрын
@@thybiscuit thank's for explanation
@vratinchauhan27146 жыл бұрын
thanks
@amumasne85894 жыл бұрын
In my spray bottle water not comes through the suction tube... what i can do
@amumasne85894 жыл бұрын
When that tube apply to the other bottle will come....
@2degucitas5 жыл бұрын
I will refrain from Shawshank Redemption comments. Oh wait....
@Shawshank085 жыл бұрын
haha! love that movie.
@bikramnongmaithem13996 жыл бұрын
Continuity equation or bernouli principles
@mehulchouhan56303 жыл бұрын
Continuity equation for working of nozzle
@tanginginamo58142 жыл бұрын
How I remove that
@diogeneslantern184 жыл бұрын
Into thin air. Great book. Immensely heartbreaking
@Shawshank084 жыл бұрын
Extremely tragic. Always reminds me of the saying - The Mountain Always Has The Last Word.
@paulettelewis29266 жыл бұрын
Would you be interested in exchanging links?
@Shawshank086 жыл бұрын
I am not sure I understand. This is my channel link - kzfaq.info/love/7kAOjH9JPW71fS_hiWSofg?view_as=subscriber If you liked this video please hit subscribe!!
@biggus66336 жыл бұрын
How about exchanging phone numbers, toots? Woo! Woo!
@calebv59252 жыл бұрын
To a shooter am watching this trying to make a mini sprayer to put it in the hand and try to make some web fluid and see how potent it is
@gabem56354 жыл бұрын
3:47
@ebicosmetic7874 жыл бұрын
We have many different nozzle heads.
@hanfucolorful96562 жыл бұрын
damn, you should add red or blue colour water to show better
@sandhyadas29163 жыл бұрын
Hey brother , are you active ? We need more videos.
@Shawshank083 жыл бұрын
Thank you! Appreciate the feedback. I'll try to upload more videos in my spare time.
@yanikkunitsin14663 жыл бұрын
Ommited the most important part - check valve
@hanfucolorful96562 жыл бұрын
damn, you should add red or blue clour water to show better
@emeraldflame61944 жыл бұрын
Times someone with an Indian accent has saved me at school | | \/
@emeraldflame61944 жыл бұрын
I’m Indian btw
@imtiyazali9173 жыл бұрын
Whers the ball bearing. My spray has a ball bearing .
@saluto13974 жыл бұрын
You know I did one stupid thing. I put a little compost into the bottle , hoping to bathe my plants in an invigorating spray !! Imagine my pain when the sprayer stopped working. I felt ashamed of my foolishness. I havr failed my plants.. How can i redeem myself ? ( Want to repair it)
@guest20073 жыл бұрын
1 mar 2021 10 am est(utc-5):thanks
@AshishSharma-ck1sd4 жыл бұрын
Close the fan.
@Shawshank084 жыл бұрын
haha! wish i could buddy. it was extremely hot and humid the day i shot this