How to: Bilge Pump Install on a Jon boat

How to: Bilge Pump Install on a Jon boat - OOW Outdoors

Рет қаралды 113,247

10 жыл бұрын

Check out my Store : 4fishingpeople.com
This is a simple how to install a bilge pump on to a jon boat that didn't come with one. I used an 500 gallon per hour (gph) pump and it is wired up to a fused switch. I didn't want to cut a hole in the side of the boat so i can up with a fairly good idea for getting the water out. So far everything is going good.
Bu this kit from one the of the following sites.
500 gpm pump: ebay.us/iS06Pp
800 gpm pump: ebay.us/uyFMSf
1000 gph pump: ebay.us/Q0RkMH
Please Subscribe, Comment, like and Share our videos.
Follow us for instagram: outofworkoutdoors
Follow us on Facebook: / outofworkoutdoors
Music intro by KZfaq User: MrNotThatFamous
Artist Name: Sinc
KZfaq - / mrnotthat. .
All Rights Reserved.

Пікірлер: 29

@ridgerunner9661 2 ай бұрын

Thank buddy! Good video 😎

@thomaseast8782 9 жыл бұрын

Thanks man! You showed me exactly what I needed to know plain and simple...

@TackleJunky81 10 жыл бұрын

Nice install bud!

@skipwadoo 10 жыл бұрын

So funny, I was looking at one of those a couple of hours ago. My lucky day to find your vid.

@OutofWORKoutdoors 10 жыл бұрын

yes. i did too but no one had a video out for me to find.

@Whymebitc 6 жыл бұрын

Good job..

@abdinvelazquez1265 5 жыл бұрын

What that piece that locks the outboard to the transom called? Did you made it or bought it?

@rickylove619 5 жыл бұрын

What size of cable for the bilge pump please

@GoSunDevils99 6 жыл бұрын

I like that you didn't drill through the hull, yeah it might not look as clean but once you put holes in Aluminum it will never quite be the same as factory. Then you're constantly having to go back and repair leaky spots with Silicon junk or some other sealant. I feel you should never put holes in your aluminum boat hull if you don't have to. One consideration I might have is stuff bouncing around in the back of the boat and knocking into your pump, breaking it. If you always drive on smooth roads maybe no issue but I've seen deep cycle marine batteries slide around, gas tanks get knocked around on some bumpy back roads when that trailer starts bouncing. My thing would be to ensure stuff is secured down tightly.

@sochef24 Жыл бұрын

Where can I find the braces you uses for the drain hose and what size are they and what are they called

@longvan8464 4 жыл бұрын

Thanks for making this video. I’m looking for a similar solution because I also don’t want to drill that hole in my hull. Can you let us know where you got those rubber hose clamps? Cheers

@OutofWORKoutdoors 4 жыл бұрын

can't remember where i got those

@joedagostino7560 9 жыл бұрын

How many thumbs do you have?

@FishingTheOdds 6 жыл бұрын

frame a deck and boat carpet that sum bia!

@foxrocks79 10 жыл бұрын

I'm new to the hole boating thing. What is the bus bar for and how do you hook one up. Thx

@OutofWORKoutdoors 10 жыл бұрын

bus bar is to distribute power to the switches.

@colinroche3559 10 жыл бұрын

is everything connected to one battery? engine, trolling motor, fish finder, bilge etc. Thinking about upgrading my jon boat, should I have a battery in the back for the engine and another battery up front front for fish finder, trolling motor, and bilge?

@OutofWORKoutdoors 10 жыл бұрын

i have everything wire to one battery and it can do a full day on a full charge(24 size battery). The trolling motor is wired directly to battery with a 30 amp breaker. All other electronics are wired from the bottom switches. My engine is a hand start so i don't use my battery to start my 9.9 hp engine. I just put most of the weight in back to help with the speed of the boat as it's travels. i can hit about 17 mph with two people on board.

@Dmonieluv 6 жыл бұрын

Is the pump automatic?

@daddymidwest4111 10 ай бұрын

Did the gas tank jump around and “Unmount” the pump?

@alexkoenig4893 7 жыл бұрын

I put probably a little too much thought into mounting mine lol . All 3/4 pvc

@alexkoenig4893 7 жыл бұрын

I also only have a 3 switch penal with a USB port so I can only turn the pump on when I turn my stern lights on because I ran out of switches and i have still yet to hook up my amp and Bluetooth receiver so I'm gonna have to figure that one out too. My advise is to get more switches than you think you'll need