generator fuel pump timing.. model 5c-17a.. you want to know?? watch this video till the end.. any suggestion please coments below..
Пікірлер: 65
@rishikeshphalke51732 жыл бұрын
Thanks for sharing this video . .....
@mahamudhossain23782 жыл бұрын
Thanks for your video,its really help for beginner..hope more video will upload regarding A/E & Boiler also.
@shaikhfareed30242 жыл бұрын
Bro good, nice informatic video keep going some more stuf
@jitu20892 жыл бұрын
Very nice video
@josea.sanchezramos85112 жыл бұрын
Good video, thanks a Lot.
@kurazhnica2 жыл бұрын
Good video!!!👍👍👍 Show some more videos on the same topic!!!
@iqbalmirza5914 Жыл бұрын
Good
@mohamed0atya Жыл бұрын
good
@aruns57503 жыл бұрын
Good video..you are pausing at important places to make us clearly understand and thats great...😃also plz show us how to adjust timing? And how to change camshaft? Just explaining will be enough as we know it is not practically possible.. thanks bro..
@marineengineerworks3 жыл бұрын
I will make video sir .. thank you have a nice day
@marineengineerworks3 жыл бұрын
Timing adjustment.... the shims .. you need to measure.. measurement as per manual instruction
@Nkgita4 ай бұрын
I was hoping for seeing an re-adjustment when it has shifted.
@phamhuong21884 ай бұрын
In my engine , the down line is mouting position mark line and the top line is Initial injection mark line .
@bellyyeramo25143 жыл бұрын
Nice thank you much.. now i know..
@osamahal-taie48422 жыл бұрын
thank for the video please any one know the suitable injection timing (angle) for himsen 9H25/33 because its not mentioned in document and when we measure the angle for the other engine in site we find wide range (8 to 16 degree) ?
@user-ve1lw7qq4p7 ай бұрын
Sir, thank you very much for the video! What does the top line mean? Where are the shims installed?
@marineengineerworks7 ай бұрын
Down side of fuel pump sir
@educoquilla7263 Жыл бұрын
Sir good day..Regarding po sa timing 6DE-18 Daihatsu..8degree BTDC pero yun line andoon n sa taas pag naka point yun flywheel sa 8 degree btdc..
@marineengineerworks Жыл бұрын
adjust ka ng sim sir... sa daihatsu miron yang sim sir sa ilalim ng fuel pump☺️
@ryanalta5757Ай бұрын
Sir wla bang fuel oil duplex filter ang GE na yan.
@marineengineerworksАй бұрын
Miron sir
@ryanalta5757Ай бұрын
@@marineengineerworks saan po banda duplex nyan sir?
@EricoDyquem352 жыл бұрын
ai nako, yun lng ginawa nyo ? wala mn kau ginawang adjustment sa fuel pump. inikot nyo lng nag inikot.
@manogaranr399310 ай бұрын
how will you identify .5 deg deviation in flywheel
@2dworld2692 жыл бұрын
Sir what is the problem if the pmax is low but higher exhaust?already changed a new F.o valve & F.O pump.
@marineengineerworks2 жыл бұрын
Sir maybe the cylinder head spindle gone.. check if your generator is hard to start.. before you start turn the flywheel check the indecator valve if there is an air.. if not your cylinderhead spindle is gone..
@2dworld2692 жыл бұрын
Thank you sir
@rodelbanilla37922 жыл бұрын
Nice video sir. Na experience nyo na po ba na makunsomo sa lub oil yong generator nyo? same model po 5DC 17A.. Tas lub oil overflow tank tumataas yong level?
@marineengineerworks2 жыл бұрын
sir tingnan nyo po yung air vent ng lube oil sir.. baka barado.. yung talsik nya doom pumonta . or else purifier or blow by.. ilang taon na yung barko sir.. yung air vent sa sumptank ng generator sir
@kulanggot29113 жыл бұрын
How does if it is not in timing? What should you replace or need to adjust? If the shim need to adjust? Thanks
@marineengineerworks3 жыл бұрын
Yes sir your correct.. shim need to adjust.. i will make a video for that in how much or how many and the measurement required.. thanks sir
@irkall68982 жыл бұрын
I can't see the engine data and engine name plate,l think the engine data very important for check and adjusting sir...
@marineengineerworks2 жыл бұрын
yes.. engine data or engine performance must always be follow..but this setuation i did not take a photo or vedio.. because im alone...and engine room is very hot.. may be nex time.. if other people not bc .. thank you for understanding
@marineengineerworks2 жыл бұрын
and firing order must always be follow. and checking carefully if theres adjustment needed.. but i think please watch the video carefuly sir . ... i already take a vedio how the inspection ...
@udayanpaul80422 жыл бұрын
Good day sir, the timing tally line is the top or the bottom one ? As there are 2 lines on the guide roller
@marineengineerworks2 жыл бұрын
Bottom sir.. fuel timing
@udayanpaul80422 жыл бұрын
@@marineengineerworksMany thanks, selamat, I really appreciate that you replied back.
@trisusilo45782 жыл бұрын
Which one adjust if timing not satisfactory sir?
@marineengineerworks2 жыл бұрын
shims sir.. you can add or you can minus the shims
@joemariediva32462 жыл бұрын
Good day.paano mag dis assembled & assembled ng Mitsubishi S6A3 MPTK
@marineengineerworks2 жыл бұрын
yanmar po ba yan sir??
@joemariediva32462 жыл бұрын
Mitsubishi S6A3- MPTK
@luisitomirafuentes4043 Жыл бұрын
sir good day po, medyo naguguluhan lng aq. pwede ba na magkakapareho ng position ang fuel pump rollers ng sabay?
@marineengineerworks Жыл бұрын
mirong tayung tinatawag na firing order boss.. kaya sundan ang firing order.. makokoha mo ang tamang timing boss . .salamat sa tanong boss
@user-zd8yw4bk7h Жыл бұрын
Sir, Mali po ang procedure nyo, ang bottom line po is base line po yun and yung upper line po yung timing line at mali po yung ikot ng flywheel dapat pataas at ndi po pababa.
@marineengineerworks Жыл бұрын
Sir paliwanag mo daw sir paano mabaliktad ang ikot ng flywheel pag komoha ka ng timing
@user-zd8yw4bk7h Жыл бұрын
@@marineengineerworks Ang rotation direction po ng DC-17a is clockwise at di po counter-clockwise, so pagkukuha ka po ng timing kelangan same rotation po ng makina. at yung bottom line po ay base line po yun at yung upper line po yon po ang position begin ng injection which is 11.5 degree BTDC sa engine flywheel.
@mackyjunelavesores66438 ай бұрын
Tama ka po boss.binasa ko po ang manual ngaun ang taas is the injection timing ung baba base line po basis po sya kapag nagtanggal ka ng fuel pump itapat dun sa base line.
@reypuda43933 жыл бұрын
Which line your are basing sir. I can't see the line
@marineengineerworks3 жыл бұрын
Sir i already sent in fb pages. Semans line.com
@user-hc6yh5oh8y7 ай бұрын
Sir mali naman po ang timing nyo..ung taas na guhit po ang timing ng 5dc-17a. Saka standard shim height 0.5mm para makuha ang 11.5 deg. B.T.D.C
@marineengineerworks7 ай бұрын
Ok sir
@bustambustam28353 жыл бұрын
how to adjust when timing difference
@marineengineerworks3 жыл бұрын
Thank you sir i will make video sir..
@reypuda43933 жыл бұрын
I can't see the line sir
@christianjaypellazo10622 жыл бұрын
shims yung tawag niyan sir dba?
@marineengineerworks2 жыл бұрын
yes sir..
@christianjaypellazo10622 жыл бұрын
kapag naka bdc ang fuel pump sir. Anong position ng inlet valve at exhaust valve sir? naka Close positon po ba yung dalawa ?
@Smiglo9004 ай бұрын
Hi. Sorry to say but this video is absolutelly wrong. First of all you are not carrying out ANY timing. You just checked if pump is at the line in beggining of delivery. You shown you adjust 11,5 degree... but this is not true... Timing is adjusted according to upper line. And you are turning the engine in wrong direction and also showing wrong stroke, you checked all when piston was at BDC. All video is completely not good. Sorry. As a proove look at your video, you are showing each pump timing at the end. Fuel cams are in different position, but each one should be at the same if they are all 11,5 degree before TDC
@phamhuong21884 ай бұрын
Your comment is correct . As the principle and instruction mannual , the down line is assembly mark line and the top line is initial injection mark line . So all video is wrong way .
@Smiglo9004 ай бұрын
@@phamhuong2188 my friend, look how many positive comments this video received during 4 years, and no any negative, this is sad 😭
@marineengineerworks3 ай бұрын
Thank you for suppurting me
@marineengineerworks3 ай бұрын
Wala kayung magawa sa buhay nyo.. your not a marine engineer i think.. you dont know or your not reading any manual