How To Change A Press In Wheel Bearing Without A Shop Press.

Рет қаралды 685,777

Күн бұрын

How to change a press in wheel bearing without a press. In this video I'm going to show you how to change a very common type of automotive wheel bearing. The press in type. These bearings are used in a lot of front wheel drive vehicles, small cars, minivans, and SUVs. These bearings are common across all different brands of cars and the procedure to change them is pretty similar.
You need to remove the wheel and tire, the CV shaft from the wheel hub. Remove the brake caliper and the brake rotor. Next, install the wheel hub adapter onto the wheel hub and use the slide hammer to remove the wheel hub. Remove the snap ring holding in the bearing, using the press kit press out the old wheel bearing, and press in the new wheel bearing. Using the wheel bearing press it press in the hub. Reassemble the brakes and install the wheel and enjoy!
Tools that I used in this video to change this wheel bearing:
Astro Wheel Bearing Press Kit: amzn.to/3t2POLQ
Side Hammer: amzn.to/3tX6yDM
Snap Ring Pliers: amzn.to/3t1Tvl6
My Amazon Store: www.amazon.com/shop/repairgeek
Help support the channel, buy using my Amazon links
As an Amazon Associate I earn from qualifying purchases and your cost is exactly the same.
I source all of my service data from the same place that professional shops do. You can as well: www.pntrac.com/t/SENKSUZKRktD...
Questions? Shoot me an email at repairgeek365@gmail.com
00:00 Intro
00:03 What type of bearing is a press in
00:34 Other parts you may need
1:21 Press tool & Slide Hammer
1:58 Vehicle disassembly
2:36 Concerns about your alignment
4:54 How to remove the hub
8:25 How to remove a rusy snap ring
10:13 Wheel speed sensor concerns
11:07 How to assemble the press tool
14:43 Pressing out the old bearing
15:44 Cleaning out the knuckle
16:07 Bearing orientation
16:50 Pressing in the new bearing
18:03 Installing the new snap ring
18:39 Removing the old bearing race (if required)
19:52 Installing the new hub
21:10 Reassembleing the car
21:40 Final thoughts/outro
#wheelbearing #pressbearing #repair
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user Repair Geek makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. Repair Geek shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by Repair Geek and therefore, Repair Geek does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge Repair Geek or anyone affiliated with Repair Geek, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

Пікірлер: 471

@RepairGeek 2 жыл бұрын

Tools that I used in this video to change this wheel bearing: Astro Wheel Bearing Press Kit: amzn.to/3t2POLQ Side Hammer: amzn.to/3tX6yDM Snap Ring Pliers: amzn.to/3t1Tvl6 My Amazon Store: www.amazon.com/shop/repairgeek Help support the channel, buy using my Amazon links As an Amazon Associate I earn from qualifying purchases and your cost is exactly the same.

@ASwordoftheLordGod 5 ай бұрын

😂😂😂😂😂😂 YOUNG MAN THIS WAS THE BEST DESCRIPTION I'VE EVER SEEN IN MY ENTIRE LIFE THIS IS THE BEST JOB I'VE EVER SEEN OF ANYBODY LAID OUT HOW TO DO THIS. ..... I DON'T KNOW HOW MANY MORONS HAVE BEEN ON KZfaq WITH THEIR LET'S BE A CLOWN AND PRETEND LIKE WE KNOW WHAT WE'RE DOING CHANNEL AND I GOT NOWHERE... NOW THAT I'VE SEEN YOU DO THIS I HAVE THE CONFIDENCE IN MYSELF ENOUGH TO GO AND GET THAT TOOL SET AGAIN AND COME BACK AND DO MY CAR ON THE SIDE OF THE ROAD ...... THANKS A LOT I APPRECIATE THAT

@ASwordoftheLordGod 5 ай бұрын

God bless you in return thank you for your honesty thank you for sharing

@danaeverhart6487 5 ай бұрын

Hey mate! You always replace the hub assembly it’s cheap and makes a great repair!

@kalani1963 4 ай бұрын

Great video, thank you very much. Question, did you leave the Ring that protects the speed sensor, or did you land that in when you removed the bearing. Also, will this process work on a 2010 ACURA TL?

@petehenderson 2 ай бұрын

U don't press against the middle it will ruin the bearing

@ArapStiile 5 ай бұрын

This man was thorough and explained everything in exact direction. This is by far one of the best instructional I've watched.

@justsomeguy1074 2 ай бұрын

Yes it was very clear and well shot!

@PinwheelHomes Ай бұрын

I second that. Very well explained. Couldn’t find it specific to my vehicle, but this is so clear I don’t need it anymore.

@mikec8660 Жыл бұрын

This is by far the best instruction video on replacing a FWD front wheel bearing. I’m a Honda tech by trade, and I can say that every steps, tips, and cautions are all spot on. Only thing I might say is that by using the impact gun you may damage the threads on the tool prematurely, especially if it’s a cheaper quality installation tool.

@KSG03 Жыл бұрын

I have the same tool and have used it countless times. I always put a little bit of gear oil on the threads of the bolt. Tool still works like brand new

@LeverPhile 8 ай бұрын

Yes, grease or oil the threads to protect them. No anti-seize!

@hbgutubeinfo 7 ай бұрын

I totally agree, great job in the instructions

@businessraptor127 6 ай бұрын

Dose it make a difference on which direction you press out/in the bearing?

@stlcat314 2 ай бұрын

@@businessraptor127only can be pressed in one way

@BrownFella 4 ай бұрын

The best wheel/hub bearing video ive seen yet. Very well explained. Clearly! Even a 6 year old could understand the steps. Now i just need to grab the press kit for myself instead of renting one whenever i come across this type of job. Thanks dude!

@AreaThirteenThirteen 2 жыл бұрын

Great video! Straight to the point without any unnecessary babbling, annoying music etc.

@melvinmccoy9830 6 күн бұрын

If you're not an instructor you need to be. Great job. Show and tell is everything.

@vinwilson5521 2 ай бұрын

Best wheel bearing install video I’ve seen. Great job.

@billburgess9100 6 ай бұрын

The best what, how, why, video on press in wheel bearing out there. There are too many videos on the subject that all they seem to be doing is showing off how well their impact wrench works without hardly any what and why. Thanks Repair Geek.

@jptrainor 2 жыл бұрын

A Dremel is enough to put a cut into the race. It doesn't take much of a cut to get the tip of chisel in to crack it. I've done both. Next time I'll reach for my Dremel.

@victordirectdemocrats Ай бұрын

I just place a chisel between the race and the hub, go around hammering not too hard and the race starts to separate, i foumd no need to cut into the race

@DJ7mph 6 ай бұрын

I've watched a lot of repair videos for different repairs and this guy is good. Thank you so much for this video. So well explained.

@patm95 5 ай бұрын

You made this so easy. I’ve never done it before and finished it in under 3 hours. Thank you!

@DJ7mph 6 ай бұрын

I finished doing my daughter's 2018 Buick. I bought the press tool although it was a different brand. I followed this video and everything worked great. I do not have an impact, but a cheater bar worked. A couple of things were different on this Buick. I had to take the tie rod loose. The snap ring was on the back side. After removing it, the bearing had to be pressed out the back and installed from the back. Was still able to do it on the car. I really appreciate this video. I probably would not have tried diy without it. There are a lot of videos on this subject, but this was the best.

@marcnelson2123 2 ай бұрын

I never waste time hitting the like button. But your video made this job so much less stressful that I hit it for you. Thank you for making it! I'm almost done with my bearing job.

@marvthegreat1981 Жыл бұрын

Best video on the subject. Thank you, now I have the confidence to do it. Too many people on KZfaq assume everyone understands “specialty” tools, thank you for the explanation.

@hhswerewolf9628 Ай бұрын

Finally found a video that they actually teach you how to use the tool everyone else I have seen would just talk and talk and talk and not get to the point

@markmorris2062 Жыл бұрын

This has been the best video I have found on how to do this. Mt car is similar to how this one was and made it so much simpler than what other videos are showing. Thank you

@whathappened2230 4 ай бұрын

Best video on this I have seen yet! Thank you very much!

@ExCordeEnt Ай бұрын

Absolutely awesome video. I feel like every other video pulls the hub and then just tells you to "put it on you hydraulic press". This was super detailed and perfect for the everyday DIYer that doesn't have multi thousand dollar tools. Thank you sir!

@davedeatherage4902 7 ай бұрын

The best detailed info on replacing a wheel bearing. Thank you! ( Especially the part of making sure the hub fits on cv axel spline)

@Martinko_Pcik 5 ай бұрын

I have used my dumb bells instead of that special tool to remove my rusty hub yesterday. Seeing that tool on KZfaq helped me to realize what I need when I was struggling and it worked out

@brianbanks3044 2 жыл бұрын

i like it.....i used to pull the whole knuckle off and lugged it over to the big press...if you have the right tool, your way works great...our problem many times is the snap ring is rusted solid into the knuckle or some other Northeast problem because of salt and rust...great job

@cq7415 2 жыл бұрын

Great video. Well explained and nice photography. On a comment, someone said put the new bearing in the freezer before installing to shrink it, goes in lots easier. Thanks for sharing.

@jockodog2009 2 жыл бұрын

Really thorough instruction of the tools and process. This vid will definitely help any DIYer get through the process with an understanding beforehand, which could otherwise be intimidating. Great job!

@kovie9162 Жыл бұрын

First time I replaced front bearings I ended up taking the knuckles off as the slide hammer wasn't able to get the hub out of them and made a huge racket that my neighbors probably weren't too happy with as I work on the street. I got one hub out with a small sledgehammer pounding a large impact socket that I used as a drift, but the other one just wouldn't budge so I took it to a shop to be pressed out. I got the rest done using this Astro Pneumatic tool, which was pretty straightforward. I can verify that getting wheel speed sensors out of old and rusty knuckles is almost impossible to do without breaking them, because I tried this on a 30 year old car last year and broke both of the rear ones. Each costs around $350 so I now have to either do without and put up with that annoying ABS light (or just pull the fuse) and of course no ABS, shell out $700 for new ones, or try to jerry-rig ones out of the old sensor cables which are fine and a hall effect sensor (or whatever sensor they use) with the right voltage output and a rod that fits just right in the hole. I'm going to try the latter first. Also, you should grease or lube that forcing bolt before using this tool, to make things go easier and protect the threads. And, different cars have different pressed-in bearing setups, with some coming out the outboard side and some coming out the inboard side. It's basically wherever that snap ring goes. Btw snap rings are well-named because when you remove them they snap at you, so wear eye protection folks or put something solid in front of them when you remove them.

@woodensauce1063 10 ай бұрын

I just did this on my wrx following this guide, the driver side front bearing was completely toast. I was originally going to take off knuckle, take it to a shop to get it pressed, then get an allignment after. Was able to do it for just the cost of the bearing itself. Thank you!

@fivefortyeye540i 2 ай бұрын

Highly detailed instructions absolute THE BEST

@ninjafishing7120 3 ай бұрын

Just done it .. keep the bearing straight kinda tricky . I use hammer and old bearing to put then straight before using this tools.. it works perfectly . Thanks for the video

@mathiaslundqvist9982 24 күн бұрын

Many thanks for this instructional video! Succesfully changed the front bearings on my Land Rover Freelander 1 with the help of it. EDIT: Just remember to remove the circlips before trying to push out the bearing :D And fit new ones after installing the new bearing.

@christophercraig9295 Жыл бұрын

Thank you so much for this video. After watching this I'm confident I can change mine rather than paying the dealership to do it or buying pre-pressed full knuckles. You so right, the bearing and new hub are quite inexpensive. I can get both for less than $100! And the pre-pressed full kuckle would have cost me $900 for both!

@Ratlins9 Жыл бұрын

Superb video, the camerawork, narration and explanations and tips are spot on. Thank you for taking the time in producing this video and sharing your knowledge.

@sakaraist 5 ай бұрын

Solid video. As for everyone saying to anti-seize, loctite, or lubricate the splines, this is actually incorrect. (I live in northern canada, I'm familiar with 8 months of snow and anything possible rust-welding together...) The tolerances, assuming you're using decent parts. are tight enough that what you apply will be almost entirely pushed out towards the hub as you tighten the axle nut. This can result in, depending on the design of the hub, you hydrostatically locking the fastener during clamping. Which will not only wildly skew torque readings, but also put immense pressure on your components and cause premature failure. Anyone who's ever torqued bolts in blind holes, such as engine blocks is likely familiar with the fact that even a tiny bit of oil between your fastener its clamped object can crack straight through solid metal while torqueing it down. This is the same principle, less likely to happen but still entirely possible. TLDR ; Fluids don't compress, and cause bad things to happen. Read the manufacturers installation procedure and only apply the specified lubricant if a wet torque is provided. Most vehicle manufacturers will even deny warranty payout to dealerships if there is evidence of a lubricated fastener where a wet torque is not provided. ALWAYS RTFM, if it seems odd then look for a service bulletin to confirm or deny it.

@yazming1720 Жыл бұрын

140 pds of PURE GENIUS 💪💯💪💯💪💯💪 Please keep the DIY videos coming

@2005Pilot 11 ай бұрын

Wow!!! This is The BEST and most detailed instructional video on this procedure that I have found! I really don’t know how it could be any better. Certainly gives me some confidence in performing this on my Pilot. Thanks for such a Great Job! New Sub and Ringing da Bell😊👍👍

@markcollard9326 Жыл бұрын

I always thought you needed to use the outside of the bearing to push it in, not the inside. I do them just like bushings, I would have used a larger plate to cover the entire bearing and push it in by the outer race, if you push it in using the inner race you can damage the bearings.

@chadcramer4024 9 ай бұрын

If you watch going in he pushed on the outside!

@kay-zed4407 9 ай бұрын

He did use the inner bearing to press in the hub. That is the correct way to install the hub as it does not put pressure on the bearings and keeps both halves of the inner race together. If you are pressing on just the outer race there is a good probability that the inner race opposite the hub will get pushed out of the bearing destroying it. *Depending on what kind of tool is used obviously.

@patadegrillo007 9 ай бұрын

The inside bearing is supported with this tool configuration so no damage is done

@cannaroe1213 5 ай бұрын

FFS lads it has nothing to do with the inside or the outside in situation X or Y. Just dont crush the balls. Easy.

@victordirectdemocrats 3 ай бұрын

One of the best diy I have seen! Thank you

@albertoascari2542 2 ай бұрын

Thanks for showing all the steps necessary and giving a complete commentary on this..Other videos often miss out all the information needed to complete all the steps necessary and leave us guessing, I find.

@HiepLe-rf5ve Жыл бұрын

Thank you for a very thorough explanation of the job. Will be using your instruction when I do my front bearings.

@lonixlon 2 жыл бұрын

Get a welder and put a nice big bead on the race, the heat will make it expand and it will basically fall off

@bradceo2045 Жыл бұрын

Very nice presentation. I do personally enjoy watching your videos. You explain everything for the correct install. And you give secert tricks along the way. So thanks buddy 😎

@PinwheelHomes Ай бұрын

Thank you so much for this tutorial. Just changed the bearings on a 2010 Mercedes B200 and this tutorial helped tremendously.

@Averna222 4 ай бұрын

Auto tech here with something to add for the people. If you want your press tool to have any longevity, the forcing screw should be greased, which will also make it press easier. Additionally, I'd suggest separating at the ball joint instead to get the cv shaft out. Even if the strut bolts aren't where the alignment is adjusted, it can still affect the alignment somewhat if removed, whereas separating the ball joint will have no effect. Otherwise, this is a perfect rundown of how it's done.

@scarface4u2 Жыл бұрын

Fantastic explanation. I’ve changed the rear wheel bearings before, no problem. But the front is a different animal. Going to this wheel bearing puller, so thanks for the insight

@wiltonmedina6209 7 ай бұрын

Awesome. Very detailed and easy explanation of the process. I am replacing both front bearings on my Mitsubishi Outlander. I bought also the hubs. Going to be easier to replace both bearings and hubs. Thank you very much.

@bobbiebaines3452 Ай бұрын

Thank you so much. You were the only one who made such a detailed video i could find on here.

@aaronnewton9904 Ай бұрын

Thank you Thank you Thank you!! This is without a doubt the best instructional video I could find on this topic. My dude is a hero!

@bernardomanto3076 10 ай бұрын

Thank God to the whole hub assembly replacement on modern vehicles nowadays.

@JCO847 8 ай бұрын

Do you mean a pre-built new knuckle that has everything done already?

@neiljarvis8911 11 ай бұрын

Nice to see it done properly, most end up pushing on the inner to get the outer diameter and vice versa, damaging the bearin by apply massive static side loads!

@ore4133 6 ай бұрын

Outstanding explanation. Detailed and didn't seem long and boring.

@Musiclover5258 Жыл бұрын

This is at least the 10th video that I am watching on this topic, in anticipation of having to replace the wheel bearings of my 08 Pilot. And this is by far the best description, including insights into the actual physics of pulling the bearing out. Thank you so much... While I am not sure which model of Honda your vehicle is, from appearance the knuckle assembly looks identical to mine. So, hopefully I can also remove the top two bolts attaching to the strut without affecting the wheel alignment...

@Merrill26osu Жыл бұрын

Did you replace the bearing? I’m doing same on rear of my pilot. One option for the front is to replace entire knuckle assembly. It’s pricier but saves a lot of time. And I had to replace abs sensor as it was froze in old knuckle.

@Musiclover5258 Жыл бұрын

@@Merrill26osu It so turned out that the noise from my wheels were actually coming from the tires (got this confirmed with a mechanic as well). So I did not attempt this repair. And yes, the far easier solution for worn front wheel bearings might be to replace the knuckle assembly as a whole. However, this option did not seem available for rear wheels. The process also looked more complex than front wheels due to the parking brake assembly, and I was not able to locate any video instructions for rear wheels. How did you handle it?

@JCO847 8 ай бұрын

@@Musiclover5258 Rear wheels at least on my Hondas are a piece of cake vs this. You just unbolt the wheel hub and bolt a new one on (the hub and bearing come as one unit)

@Musiclover5258 8 ай бұрын

@@JCO847 I am assuming yours is 2009 model or later? For Honda Pilot 2008 and earlier, it is unfortunately the more complicated route 😞

@JCO847 8 ай бұрын

@@Musiclover5258ahhh I was talking Accord. No drive wheels in rear so easy bolt on hub. I assume with AWD then you have axle nuts and press in bearings etc in the rear too is that right?

@nicmic6138 Жыл бұрын

Nice seeing one so young doing these videos

@franksargeant5726 4 ай бұрын

This demonstration was very understandable! Thank you very much. 😊

@ayeeiou9147 2 жыл бұрын

Excellent video! I feel encouraged! 👍

@TimothyDepew-ud6sj 6 ай бұрын

Good Video. Quick, simple and accurate. Thank you

@jockesgarage6049 Жыл бұрын

I have this tool. Never use impact gun but now i got to do it. Locks so easy.

@toddcott9510 Жыл бұрын

From Scotland. The snap ring is usually rusted up so bad that its almost rusted away, I find that welding washer or bit of steel to it , then use a slid hammer with vice grips, will shift it. It's all down hill from then. Good demo, by the way.

@smiller787 Ай бұрын

Great video….on the taking the two strut bolts lose (alignment bolts or stock non adjustable bolts), I would before you do any work, while the car still can be driven, pull up to a relatively flat surface close and convenient to where you make your repair, and pull up and park with your wheels as straight forward as possible. Get out of the car, and mark the road with chalk, where your tire stopped (the contact patch and direction to give reference after repair). I would also mark the top of your tire to take in wheel runout to your next measurement(could also mark in paint, the tire, wheel, and hub together for more accuracy). Next using either a digital angle meter (preferred) or a level large enough to span the sidewall of the tire, take a measurement of the vertical centerline of the tire wheel and hub. Changing those strut alignment bolts primarily change the camber (left right tilt of top of wheel) so duplicating this angle after disrupting those bolts, to before the work started, if the car was in reasonable alignment should get you back in the ballpark or confirm any marking of the strut pinch point before disassembling is accurate. You could for an extra measure, also take an angle reading of your opposite front wheel to determine how close both angles are. They make a small square digital angle gauge pretty cheap, that used in conjunction with a level or accurate straight edge can measure angles accurately. If you don’t want to spring for that, a bubble level, and a tape measure can be used. Word of note, if your worn bearing has play, this must be factored in. That’s why taking the angle of the other wheel, helps if the car was in reasonable alignment before starting. So now after you make repairs, you drive car back to the spot you created, and getting the wheel/tire (and car) to stop in as close to where you took measurements before, including getting tire wheel reference to the top. Take your angle measurements again, write them down, if they match, your done. If not, calculate the difference between before repair and after, then you’ll need to jack the car up just high enough to free front wheel, on that side. Take another angle measurement and then loosen the alignment bolts on the strut, and move the eccentric bolt to correct for the difference of your two initial readings. Tighten bolts, drop the car off the jack, and this is important, drive the car…..then remeasure your angle again at the same spot with all things being equal. If your camber angle is the same as when you started congrats, if not repeat. If you did this correct, you should be good, if you doubt, a trip to the alignment shop might be in order. Lastly alignment specs are usually done in degrees, or rather fractions of a degree. For reference, a circle with a radius of 57.3 inches (diameter of 114.6), one degree of angle taken from the center of said circle, will move one inch at the circumference, so for example, if a spec calls for and 1/8 of a degree, the deflection will be 1/8 of an inch at 57.3 inches from the center of the circle. So tiny measurements closer to that circles center make a difference. Luckily specs usually have a range, and camber is more forgiving then toe or caster, the latter being in newer cars not adjustable. Camber however changes toe, so getting it as accurate as possible is best!

@TheFlyerBill 3 ай бұрын

Thanks for the well delivered process! Great job.

@samaccurso 11 ай бұрын

Great video, you explained most important info. I needed because I don't own a press, thanks very much!

@bmlaforge 10 ай бұрын

Dude, I love your personality and common sense. You just got a subscriber and a like, and I rang the bell for all notifications. Thank you so much for this!

@mickl8212 Жыл бұрын

Wire wheel to clean out the snap ring groove. Assemble using a very light oil. Nice video.

@hhattingh Ай бұрын

As a DIY'er thank yiu very much. Makes perfect sense in 20/20 hindsight

@arthurhernandez6124 7 ай бұрын

That is what I needed! Step by step, thank you!❤👋😁

@ripcdburnme 4 ай бұрын

VERY thorough and informative. Good video.

@Ram14250 2 жыл бұрын

Great video! Thanks for posting this!

@jr2492 Жыл бұрын

Excellent video the best so far. it cleared a few doubt I had about this project

@MrTag189 Жыл бұрын

You can use a welder on the inner race to provide heat..

@tuffguy11505 Жыл бұрын

Very well done tutorial, greatly appreciated.

@flobeeonekinobee2353 6 ай бұрын

Outstanding video! Love the explanation of everything

@AreaCode862 Жыл бұрын

Best video by far pertaining to this topic!

@moojuice369 2 ай бұрын

I added an extra 10 lb plate to the slide hammer and the added mass helped a lot ..😉😄

@ericvalmores6366 8 ай бұрын

Wow nice job, pretty straight forward. Thanks

@dougrognlie8009 11 ай бұрын

Nailed it! I totally agree with Mike C. Best instruction video for replacing a FWD front wheel bearing (and without removing the steering knuckle). I never would have guessed that you can do this on the car. Thank you so much RG. Oh, and your sound & camera work are exceptional!!!

@2005Pilot 11 ай бұрын

Yes they are- Extreme Professionals on this channel and it’s Greatly Appreciated 👍👍

@fil1329 5 ай бұрын

You forgot rear drive hub bearings too on AWD vehicles

@andrewvillavicencio8496 Жыл бұрын

Great video thanks man. Good tips and pointers!! I am getting ready to do this on my daughters' 2005 Accord and was a little worried as I do not have a press. Problem solved! SUBSCRIBED

@gizzard1987 Жыл бұрын

Very nice video. I have this exact same bearing puller/installer set. The anti-sieze all over the bolt and washers is a must. I haven't used mine with an impact yet but here in the rust belt, a 4 foot pipe wrench is often the best for turning these seized bearings out.

@roccozarcone4393 Жыл бұрын

You’re a master at your work excellent explain very well

@edgartopico5595 Жыл бұрын

Great step by step video tutorials and easy to follow instructions. Thank you for sharing your expertise. Btw I am your new subscriber.

@CTGDesigner 3 ай бұрын

Excellent video!! I was contemplating taking my new hub and bearing to a shop to get it pressed. But I think I'll buy a bearing press kit and slide hammer.

@johnnyhotrod 11 ай бұрын

Excellent explanation,thank you!

@kenpallister5804 2 ай бұрын

Truly excellent instructions. Well done!!

@peteturton2307 2 жыл бұрын

That was very well explained. Well one.

@darrensaltiel440 Ай бұрын

i was so into the vid i moved my head when the snap ring came flying out of the bearing 😂

@tikaramsingh7509 3 ай бұрын

Love your explanation,Awesome 👍

@CalvinJ82 9 ай бұрын

Thsnk you, thank you, thank you for the demo on this. Most helpful. Acura MDX dust shield removal, this helped a lot.

@wty1313 8 ай бұрын

One of the few videos that show using this type of tool the way it was intended to be used - without removing the knuckle. This type of tool was originally intended to allow changing a pressed in bearing without removing the knuckle and using a shop press, thereby saving time for the technician (ie. Hub Tamer and subsequent Hub Grappler), and usually the need for alignment because the knuckle was removed. In a lot of videos, the person takes the knuckle out THEN uses the tool to swap the bearing. Granted there are times when you have to remove the knuckle, but it's usually times when it has to be removed because the bearing is seized and a shop press HAS to be used anyway.

@aireworkz929 Жыл бұрын

Fkn awesome, need my daily civic SI done. Ordering the bearings now. Thanks again.

@striela1 Жыл бұрын

Excellent video, thanks a lot!! Greetings from Italy!

@BIack-Moon Жыл бұрын

Splendid my brother. The wheel bearings on my Jaguar X-Type in the front is going and they are Pressed in. This will help me greatly... I have a Ingersol impact drill paired with old Betty(BFH), Nothing will stop us. I gotta check tho to make sure thor returned my 🔨...lol great video!

@henrycortez7816 11 ай бұрын

Great explanation dude! Thanks!

@edwardjdm 4 ай бұрын

Well explained. Thank you for this video

@iamhapidays8766 10 ай бұрын

Your high and top quality video and outstanding step by step effective instructions made me subscribe.

@tomknud Жыл бұрын

Marvelous video, thanks.

@staind288 2 ай бұрын

Great detailed video. Thanks, repair geek!

@daveysmithRSA 9 ай бұрын

Very useful video content. Thank you 😊

@vrod1a 11 ай бұрын

Very well done and explained 🙏

@leeh9420 2 жыл бұрын

Great vid. (as always) - thanks!!

@raywaldeniii6279 2 ай бұрын

Loved the video. Bought $179 kit. And … would remove the old bearing

@dottega 10 ай бұрын

😂❤😂😂❤❤ I love the lbs4lbs comparison. Great stuff.... the best video man. Thanks!

@maxagent86 Жыл бұрын

There is an easier way/tool to remove the hub than with a slide hammer: Astro Pneumatic Tool 78830. Thanks for another nice video.

@RepairGeek Жыл бұрын

Slide hammer is half the cost though.

@kittyhawk2171 6 күн бұрын

Not easier on the wallet. Astro Pneumatic Tool 78830 costs over $200. Slide Hammer costs less and has more uses.

@imgannadie991 2 жыл бұрын

These are my favorite types of bearings to do. In and out usually 15ish mind

@jeffreydomara9625 Жыл бұрын

I prefer your wheel bearing replacement its straight forward an easy to repair.all good thanks for the information