How to change EGR valve in 06 Dodge Charger/Chrysler 300 3.5L V6

Рет қаралды 31,304

Gibson Garage Speed Shop

Күн бұрын

Might as well lie down on the engine
Merch now available!
streamlabs.com/gibsongarage/m...

Пікірлер: 24

@FeLLoNeY 9 ай бұрын

This is the only video that makes this seem doable great job !!!👏

@chuycastro9910 Жыл бұрын

Thanks for the help my guy. You’re highly appreciated.

@GibsonGarage Жыл бұрын

No problem 👍

@benignomarin-real3972 Жыл бұрын

That EGR tube is a big challenge for DIYers and inexperienced mechanics. If handled improperly can lead to damage to the intake and the intake gasket not sitting properly and causing massive vacuum leaks. What I do, to prevent all that, is; disconnect the tube from the EGR and connect it first to the intake using a new gasket. Then lower the intake carefully leveled and parallel to the contact surface. Not angled! That bends and kinks the gasket. At the same time you lower the intake watch the other end of the EGR tube sits in place. Tighten the bolts of the intake and the two at the EGR at the same time little by little in stages.

@mikekasich836 11 ай бұрын

It turns a simple 10 minute job removing the intake into a fucking extra 30 minutes removing all the wipers and everything just because they couldn't figure out how to build a EGR pipe that fits

@mikekasich836 11 ай бұрын

Do you think there's any kind of flexible metal hose that can be used to replace it?

@MarcyMckeefer 7 ай бұрын

Yeah I had this problem; did my spark plugs and when I went to put the intake back on I couldn’t get it to line up right with it for nothing. Had a huge leak so I took it back off to try again and finally the pipe moved some so it went into place but then must’ve came lose from the egr bc you smell strong exhaust coming through the ac and the car lacks power. About to take it all off and try again. Probably just add another screw up to have to fix 😖

@vsh510 Жыл бұрын

Easy job 30 mins tops extension with 8mm bolt to tighten egr tube down also removing that bar that goes across engine makes it quicker

@lamar07103 Жыл бұрын

Wish I would have seen it done this way years ago..

@claybirdgod 8 ай бұрын

Appreciated

@lamar07103 Жыл бұрын

So the throttle body stays attached to the manifold? What about removing that top brace?

@GibsonGarage Жыл бұрын

If you need to for more room

@DAMA.07 5 ай бұрын

What tools did you use?

@justindungey4197 11 ай бұрын

Should of marked location of windowipers with a piece of blue painters tape . So that when you reinstall easy to set them in

@dionnyduran2900 11 ай бұрын

at 3:55 what is the name of that hose that says PCV and has an white arrow? I need to know so i can replace mine?

@GibsonGarage 10 ай бұрын

pcv hose or breather hose

@juanitagonzalez179 Жыл бұрын

Wish you could help me fix my charger I have the same problem but hard to find someone that knows how to

@moisesramos476 10 ай бұрын

Did you ever fix it? It's really simple, the hardest part is taking that passenger windshield wiper arm off.

@MarcyMckeefer 7 ай бұрын

What did you say you put down the bolt holes of the intake before you put it back on?

@KingsCountyDrone 7 ай бұрын

Locktite

@isaiahpeshlakai3629 7 ай бұрын

Which way do you unscrew the 2 egr bolts connected to the bottom

@GibsonGarage 7 ай бұрын

They're normal right hand threads

@jakewoolwine9 Жыл бұрын

1st to comment

@GibsonGarage Жыл бұрын

You can't comment "first to comment" because that's not really a comment you got to make comment and THEN brag about you were the first to comment