How to change light bulb for brake or turn signal on 2015 to 2022 Chevy Colorado

Рет қаралды 31,885

Жыл бұрын

This video will teach you how to do a brake light replacement on your 2015 2016 2017 2018 2019 2020 2021 and 2022 Chevy Colorado. You will learn how to do a tail light bulb replacement on your 2n generation Chevrolet Colorado or GMC Canyon trucks! In this video you will learn how to change the bulb in the tail light light of your GM Canyon or Chevy Colorado. With this video you will learn how to repair a burned out light bulb in the tail light of your ZR2 Chevy Colorado. How to change | install | replace | remove 2015 2016 2017 2018 2019 2020 Chevy Colorado trucks' turn signal/brake stop/tail lights bulb. This Video shows the step by step process for replacing a burned out brake or turn signal light in the tail lights of your GMC Canyon or ZR2 or Chevy Colorado Z71 trucks!
Here is the affiliate link for the
SYLVANIA 7443 SilverStar High Performance Miniature Bulb : amzn.to/3ByvaHZ
Craftsman Hand Tool Set Phillips Screwdriver Set: #2 x 4 Inch, 6 inch, and 8 inch : amzn.to/3xbB9zx
and as Amazon Associate I earn from qualifying purchases and is much appreciated by us for supporting us through using our affiliate links!
#ChevyColorado #ChevroletColorado #howto #gmcanyon #chevycoloradozr2 #coloradocanyonenthiusiasts #brakelight #chevytruck #gmccanyon #lightbulb #chevycoloradoz71 #zr2 #bulbrepair #zr2bison
Connect with us on our Facebook groups:
Chevrolet Colorado z71:
/ chevroletcoloradoz71

Пікірлер: 32

@dougp.558 6 ай бұрын

Good video. Helped me out. I didn't know about the push pins and thought I was going to break something off until I saw this. Thanks dude!

@colleenechanove516 4 ай бұрын

Thank you so much! Your video was great and very informative! I did both all by myself and was able to show my daughter some girl power.

@sudonymh Жыл бұрын

I'm sure your guidance works for a clean truck, but mine was dirty, and that bulb connector would not turn no matter what. It was helpful to know which way to turn, so thank you for that. After much struggle, I was able to turn it by inserting a flat blade screwdriver between the connector and the housing lip and gently prying up WHILE turning. As always, this should be done with caution since it is plastic after all. Thanks again.

@28TrucksTravel Жыл бұрын

Well my truck was covered in sand all over back in the lights and I thought about showing how I had to do a deep clean up in there but figured most people wouldn't be interested in that part.

@OverlandPNW Жыл бұрын

Nice job on this video! Very detailed how-to. I like that!

@28TrucksTravel Жыл бұрын

Thanks and that's cool of you to say since you own a 4runner!!!

@lightgrove7751 9 ай бұрын

Truck fixed, thank you

@whoeever Жыл бұрын

Thanks this is a super helpful video.

@28TrucksTravel Жыл бұрын

Glad it was helpful!

@projet2907 Жыл бұрын

Don't touch the bulb with your fingers. It is also written in the instructions. Thank You for this video. The plastic push pins are very cheap, one of mine lost a little holding leg, it broke pulling out. Dealers do not sell this part only!

@ChrisHunterSavesTheDay Жыл бұрын

Thanks!

@hueandsteve1989 Жыл бұрын

Very helpful, thanks.

@28TrucksTravel Жыл бұрын

Glad to help you!

@Apeekachu 4 ай бұрын

Hey man I liked, subscribed and hit that bell. Ill make a playlist of your videos so they can play while I'm away! Hope this helps like you have helped me. I do have a question I live in the great white north salt and sand always gets into my harness and my bulb connectors tend to rust to the harness connectors. Is there any thing for that you would recommend, maybe like dielectric grease? I had a really hard time getting the bulbs out as they were rusted to the connectors. I made a big mess of things and had replace the entire harness. Thanks in advance!

@infdante1 Жыл бұрын

Helpful 😅

@moby8882 4 ай бұрын

This was perfect. Thankyou because those guys who give you shit for this and that did not help me fix shit.. These trucks are awsome cause they're easy to work on

@Scott-dl1ui 4 ай бұрын

Can you use LED bulbs, or does that cause issues, fast blinking, etc?

@ogtimmy2355 Жыл бұрын

I have the same issue. My bottom bulb doesn’t light up when the lights are on but does light up when I press the brake. I guess it’s still a bulb issue.

@28TrucksTravel Жыл бұрын

Yep, two different nodes in there.

@jimmyd6695 Жыл бұрын

You should never touch the bulb with your bare fingers. The oils from your skin can cause the the bulb to heat up and burn out prematurely. Just FYI

@28TrucksTravel Жыл бұрын

Thanks for the tip!

@joshjames7869 Жыл бұрын

Hey, so my running light is out but the brake light works, it seems there is only 1 bulb... is that right or do I have other issues? It's the bottom one exactly where yours was out, did the brake light come on when you hit the brakes or were both out for you?

@28TrucksTravel Жыл бұрын

I'm not really sure but generally one light bulb can sometimes do 2 different things. Use a partner to stand behind the vehicle and watch your lights while you test it out!

@FAONWN 8 ай бұрын

This is what is going on with mine.

@malachipatz3576 8 ай бұрын

Looking for an answer in the comments! I have changed my bulb on my left rear light, yet my “rear light failure” warning won’t leave my dash everytime I use the turn signal. Bulbs work but every time I turn it on after the first few clicks it begins rapidly flashing and giving the warning. Advice on how to correct this?

@nicklay1080 8 ай бұрын

did you swap it for an LED light? If so, you need to add a load resistor. this tricks the electronics into thinking you still have a halogen bulb, as they act very differently.