How to change rear shock absorber on BMW E60 [TUTORIAL AUTODOC]

No video

How to change rear shock absorber on BMW E60 [TUTORIAL AUTODOC]

Рет қаралды 30,697

autodoc.co.uk

Күн бұрын

Пікірлер: 32

@autodocuk 6 ай бұрын

Attention! This video contains mistakes: 06:48 - the tightening torque is 27 Nm, not 55 Nm. 08:38 - the tightening torque is 165 Nm, not 72 Nm. 08:45 - the tightening torque is 100 Nm, not 80 Nm. 08:51 - the tightening torque is 100 Nm, not 75 Nm. 09:37 - the tightening torque is 110 Nm, not 75 Nm. 10:43 - the tightening torque is 28 Nm, not 38 Nm. We're sorry for the inconvenience 🙇‍♂

@gideonbouwman4904 Жыл бұрын

7:47 nice cross-threading mate :D

@autodocuk Жыл бұрын

Thanks for your positive comment! Stay with us!

@Rich.Wilkin 2 жыл бұрын

Very well put together video hood work

@iconicars3050 2 жыл бұрын

Amazing diy

@andresburgos5802 4 жыл бұрын

I lake it. Very good

@alexey9900 4 жыл бұрын

Good 👍👍👍

@boumou3475 4 жыл бұрын

👍 👍 👍 Thx

@juliusboy001 3 жыл бұрын

What is the real time? Approx?? Please!

@Obelix516 2 жыл бұрын

What sort of extension did you use to take off the bottom bolt from the brake caliper bracket?

@autodocuk 2 жыл бұрын

We used the 1005S-7 HAZET

@Vaniskovce 3 жыл бұрын

You don’t have to disassemble that much. Just take out the druk insert.

@The_North0 Жыл бұрын

Right

@lewis72 Жыл бұрын

7:42 How did you get the lower strut to be the same height as the knuckle ? My knuckle is much higher in its free position. I have to stand on it to get it to lower to the right position but then I am unable to get the bolt in.

@autodocuk Жыл бұрын

It is not possible to answer your question, you can find this information in the technical documentation for the repair of your car or we recommend consulting with your mechanic.

@lewis72 Жыл бұрын

@@autodocuk I've since attached the lower strut to the knuckle. It required me pushing down hard on the knuckle to get the holes to align. When the lower control arm is installed, the bushes' torsional stiffness give it a no-load position, which should, presumably, be about the vehicle's static ride height.

@lewis72 Жыл бұрын

What is worth emphasising, as it was a mistake that I made, is the the orientation of the top plate has to be correct when reassembling the the strut as, unlike with the front strut, you can not rotate it once it's assembled.

@autodocuk Жыл бұрын

We are sure that your comment will be useful for many of our viewers.

@The_North0 Жыл бұрын

What happend if reassembled in the incorrect orientation?

@lewis72 Жыл бұрын

@@The_North0 You can't get a bolt through the bottom hole of the strut to bolt into the knuckle, as it points the bolt away from the knuckle hole... as I found out last year. The front strut can be rotated on the top mount bearing to fit. The rear can't.

@The_North0 Жыл бұрын

@@lewis72 interesting. I didn’t know that. I replaced all my struts four years ago and I wasn’t aware of that.

@lewis72 Жыл бұрын

@@The_North0 You can't rotate the bottom of the strut to align the bolt hole to the knuckle bolt hole. As the interface between the strut top and the body is held by 3 bolts, you can have it at 0, 120, 240 degrees.