This is the kind of video e-bike people can really use. Thank you.

Your video was easy for all people to understand Congratulations on furthering your work. Continue your work better and better thank you

Its exactly what i needed, thanks for sharing ideas.

THANK YOU Your videos are best, Best channel about E.V ebike.

Nice repair 👍 thanks for sharing!

Word of caution on buying a replacement throttle. I just saw some throttles for sale online, claiming they were compatible with ebikes. But a short line in small font buried way down the page lists a spec that says the Hall sensor signal varies from 0.8V to 2.4V However, 2.4V is *not* a sufficiently high-end Hall sensor voltage for most ebikes. Also, most people probably would either not see the 0.8V-2.4V spec and/or many people would not even know what it means and would ignore it assuming it was normal. Unsurprisingly, there were many reviews from buyers that were disappointed the throttle didn't work after they installed it. From what I could tell the sellers didn't seem to care that this was a major issue and likely aren't going to change their web pages to make it more obvious or provide a warning about this lower than required Hall sensor voltage output for ebikes. With a simple change to the web page, the sellers could save a lot of customers the frustration and grief of spending time and money on trying to repair or build their ebikes using these ultimately unusable throttles.

This is very helpful good work guys

The comments are very good. I had my experience with the Aston Rider kit, it came out less than 300usd with lifepo battery and it has been running without problems since I had it more than a year ago

Clear and concise, very useful thank you

Very good video clear-eyed

Does the brushless motor controller support different hall sensor numbers or they must be a. Specific one.

Clean and tidy work. Good tutorial. Thanks.

❤ you make my day, thanks a lot

Thank you so much ❤️ this video very useful for me and thank you so much 😘 bro 🙏❤️❤️❤️

well done master, there are a lot of interest points in this video.1) the good position and good skill for welding 2) the good phases for checking an electronic tool 3) the importance of grease and a lot of other informations, thank you very much.

Well done exactly right thanks.

I hadn't even considered this is what might be wrong with my scooter. Nice video, I'm gonna test this today

Thank you, very informative 👍

Very nice video throttle sensor problem 💯 thanks

Thanks .im from sri lanka.sloved my problem

Thanks alot, was so helpful

Great help. Thank u.

Thank you i leant one new work today

Hello great video. I have a question if you can please help me I have an electric sitdown scooter with 3 speeds the battery indictes thats it is fully charged but it seeems to only go one speed even when switched to highest gear. It went about 50Km an hour when switched to the 3rd highest gear but now only does about 26km..Is the battery going out? thank you so much.

Very helpful ☺️❤️

Thanks that's very useful to me

FUCKING THANK YOU, IT TOOK AN HOUR TO FIND SOMETHING THAT SHOWS HOW IT WORKS

Very well explained and very informative. Thanks a lot.

Great video...exactly what I needed, to fix my electric scooter.

It works for me.. Thank you

great video. question…. what brand hall sensors are you using as replacement? /Bklyn👑

Hello,another question. How sensitive are the Hall sensors?. Do you break downloaden immediately in you beak downloaden immediately you accidenttally swap thepoles wen you connect them?. Manni W.

Very nice video

May God give you good health and intelligence because you would show us what happens when we have no way to speed up. Note 10 with congratulations

I tore off 3 of the 6 wires on my mothers bike when i tripped and i grabbed on to it... First i playned to resolder them but the housing can't be taken appart without breaking it. Have been looking around everywhere for a new throttle with 6 wires but i can't find one. The only thing that was printed on the throttle was "DE PU 25.9v". Only other thing i noticed about the throttle is, that it is progressive/stepless twist throttle. Some advice would be appreciated.

Cool dude i got one i need to fix now i know how thanks

I am curious to know if taking out the hall sensor "chip" is really just that easy as in video? It seems like the two throttles I have tried with have NOT wanted to pop out of the slot / housing of hall sensor. are they ever glued in by manufacturer? Or am I doing something wrong? Thank you:)

out standing wow great to know thanks for the video two thumps up .

good idea,.. thanks my boss

How do you make the 5 volts going to it????

what size battery you use to check voltage can you use a just a 12v or will it fry the wires ???????

Thanks for this

Good information sir.

I hope you can make videos how to install lights direct to controller with explanations. for 36v,48 and 60v. because for all I know, most lights are 12v. some are autovolt. but since I want to change the controller and lcd, the lights has no indication what voltage it is. and the controller doesn't just accepts any voltage.i am afraid I might damage either the controller or light. what will I do? some says, buy converter or some says, just connect it to series,..but let's say I wanna preserve the stock lights yet I don't know what voltage are the frint and rear light.. what will I do?thanks

Will a bad throttle sensor make a buzzing sound come from my rear hub from ebike Along with intermittent power to the throttle?

The connectors on my controller has 4 wires(grey white brown and black) into 1 jst-sm connector for both the brakes and the throttle. And the grey and white are supposedly for the brakes. How do I test the controller alone with a multimeter ? And what should the readings be ? Just need to know where to connect the throttle wires ?

hey there i have a ebike that comes with a twist throttle i want a thumb throttle so brought one thats the same connect type etc for my bike plugged it in and screen comes up with error 4 |? i tryed 2 other thumb throttles which my mate had with same connector and error 4 again i cut 1 of the connectors off the thumb throttle and re wired it so its black to black as normal and the 2 remaining wires just switch round boom all works fine now no errors which is good so guessing the signal wires for my bike and thumb throttles are wired different but like i said all gd now its only a signal wire and positive should be all gd correct ? as its all working ? cheers

What can I do if these wires were pulled out of the twist throttle? Can I solder them back in?

Well done

I've managed to snap one of the pins off the sensor to be able to solder to. How do I attach back to sensor? Is it possible?

Hi and thanks for another great video! Keep up the good work, best regards from Greece!

i just replaced my throttle and it didnt fix the problem. i can use walk mode from the display to make my ebike go 3mph though. could it be throttle control components in the controller are broke? sugestions? where is bafang tech support? thank you

I have a 36v scooter and the thumb and break are 3.3volt, all my 5v controls don't work on it. The controls were physically broken off, any idea where I can get 3.3volt replacement controls? The scooter is a Jetson bio/ion if that is any help.

Thankq usefull vidio.

If the signal voltage is increased, will the speed increase?

Thank you very much

I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue.☠️

But if throttal volt from 0.8v to 3.6 v is it rgiht or not thanks

Great video. I'm trying to see how everything is hooked up. Are you just connecting crocodile clips to multimeter and throttle only?

Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?. Thanks 🙂

Can we use throttle direct with battery without controller?

شكرا لك

Good job boss

Where can you buy the sensor from need a few ???

Thank you

Thank you.

*Where did that third wire to test it come from?*

very nice. my e bike moves without giving throttle. may i know the reason why

I have changed my hall censor Twice and I still have no throttle at all. ? Can you think why it has stopped working, could it be the control box , I still have peddle assist but no throttle what so ever

How can I install a multimeter on my electric scooter I want to monitor battery while riding and charging I have a 1000w 48v 20ah lithium battery do I install between battery n speed controller

could you make a tutorial on how to attach a 3pin cable for a bafang motor to a throttle like this?

Throttle of my vehicle works when I switch the vehicle on. Provided that I keep the throttle engaged. If I let it go, then i have to switch the vehicle off and on again. I have to do this continuously. One time it worked perfectly for a day or two, without any hiccups. Now it's acting up again. What do you think is the problem? And the best and cheapest possible solution?

Thanks

Hey, Is Xiaomi M365 motor control 36V350W replacement for Windgoo M11-A ? Thanks.

Hi, first of all, thank you for this very usefull video. I have a problem with my e-quad throttle reaction, I have 4 different throttle, one finger type and three twist type, I measured the output signal as you discribed and didn't see any major problem but the motor driver doesn't give any response during the first angles of the throttles, but after the first 4-8 degrees, the motor starts to spin with a higher speed than desired and it makes a bad feeling on driving characteristics of quad. Between the 4-8 degrees to max throttle, there isn't any problem. Because of this issue, I can't drive the quad at very slow speeds below 5kph. Do you have any suggestion to fix this issue? Thanks. I checked this issue with another motor driver as well, and the result was the same.

What happen if in running bike and sudden haull sensor with short then directly 5v goes to controller and speed increases to highest may leads to accident, pls tell me i am correct? Or anybprovision is there in sensor for that

well done, I´d like to ask you about brushed controllers, how can I adapt a throttle like this on it?

thanks

i have a problem in my bike when i ride the switch off always ? what can i do ?

I need help reconnecting a new controller. Can you help me.?

May i know the pin out of the hall sensor IC? Thanks

I have a controller that is 2 orange and 2 brown for the controller. My twist throttle is 2 white a red green and black..how do I wire it..thanks

I have electric trotinette and they did not want to turn on because one of the screws was missing, it comes down at the battery, so I did not know what was the reason for that screw, so I put a piece of aluminum and it ignited. Is my work correct?

but from Where we Buy this hall sensors?

great video, is there any way to adjust throttle start slowly pls

ขอบคุณ

How do we recognise which wire is positive, negative and return current? Is anything marked on the sensor as well?

What cause damage to that part with three legs?!

Ji, My cycle is running in full speed in standing condition but while deriving on road the speed comes to zoro within second (my kit is 24v 19.8 ah li battery,24v 250w LY1016z and LB27 controller) Battery shows 23.6v in idle condition, while deriving 2.3v dropping. Please give your guidance to find out exact issue. Thank you.

If yes then how to increase the signal voltage

Hi, awesome video thanks, I use an Hover 1 alpha E scooter so two days ago I was changing the accelerator of the scooter, and in the process of assembling it together i found out that the beeping device was lose but before I could touch it one part it's poles mistakenly touched the pole of the display panel which resulted in some weird noise and the break light blinking and unfortunately the Scooter went off and wouldn't come on again not even charge any longer , do you have any idea what could be the issue Thanks..

Awesome

Thank

nice

Taiwan hadir boos...?👍👍

I can't see sensor number on my bike throttle it is microscopic. So if I buy this hall sensor from the link you have provided, will it work in my bike?

Is this sensore or transestre?

Hi i am from PERU can you say me in what number you put the tester pleace i wanna know.

perfet

you now sensor hall 503 found case to 49e?