No video
How To Engrave Images On Slate Tiles
Рет қаралды 3,688
7 ай бұрынXtool M1 10 watt
Power 50
Speed 130
1 Pass
www.xtool.com/...
Materials used 4x4 slate tiles
Minwax quick dry polyurethane spray
12 Pack Slate Drink Coasters with Metal Holder, VIBRATITE 4 Inch Black Stone Coasters Bulk with Anti-Scratch Bottom for Drink Coffee Bar Kitchen Home Decor Engraving, Square a.co/d/hJUE8pb
#xtool #xtoolm1 #engraved #engraving #howtoengrave #laser #laserengraving #slatetiles #engraveimages #coleminorkustoms #xtoold1 #customengraving #diy #diyengraving
www.facebook.c...
www.tiktok.com...
#xtool #engraving #laser #laserengraving #xtoolm1 #woodworking #engrave #woodcrafts #crafts #craft #cars #car #howto #howtomake #diy #lol
@bradkuhlemeyer8422 3 ай бұрын
Im getting alot of people who want pictures engraved on wood can u show how to do that with the best possible outcome new follower
@coleminorkustoms8594 3 ай бұрын
Yes, we can try to put a video together and show how to do pictures on wooden projects.
@Dannos3d 4 ай бұрын
great Vid and thanks. I have tried your workflow and it just engraved the whole picture as a white square. whether its white or black . I just cant work it out what I am doing wrong.
@coleminorkustoms8594 4 ай бұрын
Make sure that your inverted picture has enough depth of black and white highlights. Your black details in the photo will be what engraves and the white portion of the picture should not engrave at all. I hope this helps.
@Dannos3d 4 ай бұрын
@@coleminorkustoms8594 thanks for the reply. I have set up a pic in imagR and used material black slate. Bought that into XCS and its like it engraves exactly like the pic but the whites engrave and the blacks dont? I just cant figure it out. I followed what you do and its the same. I must have a setting wrong somewhere
@Dannos3d 4 ай бұрын
I actually had one kind of work. I think the pic is still too bright. Almost over exposed.
@coleminorkustoms8594 4 ай бұрын
@@Dannos3d the white needs to be more white than gray, if it’s slightly gray at all it will engrave lighter causing the whole image to engrave, which gives you a blotchy engraved image.
@Dannos3d 3 ай бұрын
@@coleminorkustoms8594 really appreciate your help mate. I rewatched your vid and used several slate tiles lol and ended up with something pretty decent. thanks again for your advice and help
@acciogames2730 3 ай бұрын
What lines per cm and bitmap mode do you use? Thank you
@coleminorkustoms8594 3 ай бұрын
Lpcm at 100-120
@petramoller4223 7 ай бұрын
Thanks a lot. How many lines do you use?
@coleminorkustoms8594 7 ай бұрын
I did this on 100 lpcm but you could do more for more details it just adds more time.
@petramoller4223 7 ай бұрын
@@coleminorkustoms8594 thank you very much 😊
@Pittsipas 5 ай бұрын
How did you get a “speed” setting with an image? I have the F1 and it only gives dpi and dot, no speed
@coleminorkustoms8594 5 ай бұрын
I’m not sure how you would set it up the F1. We only have a M1 10w.
Made Better With Knowledge
Рет қаралды 12 М.
Aegina Craft
Рет қаралды 124 М.
Nonprofessional Tinkerer
Рет қаралды 3,6 М.
Six Eight Woodworks
Рет қаралды 58 М.
Mr Craftsmith
Рет қаралды 13 М.
Rob Sandstrom Designs
Рет қаралды 596