super detailed and informative video, plenty tricks and details to plan and look out for - thank you mate!!! "allowances for expansion & contraction also in mitres - WELL NOTED"... also, on a lighter note, looking at your size: Man, I would not like to be the client disputing your invoices... 😂 all-round - just brilliant!!! 👊

Looking swole. Bravo

This is an amazing job! Plus very well installed

Great video & explanations, lovely job 🫡

If sir David Attenborough met carpentry at an early life!

Very good presenter.

Awesome video and excellent notes and details.

Super useful, thanks! May I ask what the roof trim is? Looks 👌🏻👌🏻👌🏻

Awesome video thanks for your help

Excellent work I love the finish. Easily maintained compared to wood.

Really nice job 👍🏽

Very tidy job well done and thanks'

I found that the gap between the cladding and the batten when installed would be enough to allow air circulation. Having installed vertical battens then horizontal battens before I realised this meant that I have done twice the work that was needed. The product itself is very good and I would use it again.

Thanks for the detailed video. One thing I don't understand is how the boards joined together for a 2 story house. It seems like a gap is needed between the boards and it has to be covered in a manner not to direct water to the house.

Nice job

Great video, thank you. How did you complete the gap between the trim in the door reveal and the door frame? I could see the brick work so wondered how that was finished off.

Nice work, but sure wish you had covered the window install as well.

Nice work, i have a couple of questions if that's ok? 1. Do regs not require counter battening for vertical cladding to allow airflow? 2. Ho to you attach the house wrap to the block work prior to battening? Thanks for the content, i'm going to ask for some samples of that cladding as it looks really nice.

Hi Simon, just had my sample pack arrive. New build project so lots of cladding! Might the detail around the windows worked better if you had started at the window/patio doors and worked outwards? Thank you.

How come you didnt cross batten? I was under the impression moisture will be trapped in the voids without horizontal battening

I buy 1,400 sqf cladding in California, but the retailer doesn’t have a trims for around of windows doors and corners, They have only the cladding and the corners

Hello Simon, lovely work as always. Do they not supply some sort of trim detail at the bottom so it finishes neatly over the blockwork. Like some sort of Z piece, so the cladding sits over it and then it sits over the brick or block at the bottom, I think that would give you a nicer detail at the bottom, would you not agree. Atb to you and mark 👍

What end trim have you used as the ones I received don’t cover the 25mm batton they sit on. Looks like you have a deeper end trim?

Could I fit something like this over single skin blockwork? And if so, is there any way that I can externally insulate it first?

Lovely work uncle! Loved seeing you at gokarting today ❤️

|Why would you need the house wrap on top of cavity blockwork?

Is it safe to use on outdoor- exposed to direct sunlight and rainwater?

How does the right side near the fence look like? Is it just Tyvek exposed, or bricks and no tyvek?

What tool are you using to cut the planks into thinner strips?

Hi, do you know how to do a vertical joint? My wall is 5mtrs tall and the boards are 3.6mtrs, how should I join it?

looks great.. too bad that this cladding compositie isn't allowed in my country due fireclass rating E :(

Is it also possible to screw it from the inside?

would horizontal batons trap any water against the home?

Hi what if the edge of the right hand side of the window reveal goes half way through a raised bit?

Silly question but can you do cladding over a stone extension?

Do you have a video of an horizontal install?

Is the sold in California?