How To Fit Rear Parking Sensors | Easy Installation

How To Fit Rear Parking Sensors | Easy Installation | Ford Fiesta

Рет қаралды 115,813

Күн бұрын

Instagram: / ewan_williss
In this video I go through, step by step, how to fit rear parking sensors to a Ford Fiesta 2014.
The sensor kit I am using is X-Vision.
The process is the same for most Fiestas but slightly different for other models.
If you found this useful, Please Like and Subscribe.
Comment below for any video suggestions.

Пікірлер: 63

@ewanwillis8514 3 жыл бұрын

Please Like & Subscribe

@MartinSmith-pv3zf 2 ай бұрын

Many thank's ive been thinking of doing this job on my v70 for the last 3 years, since i sold my range rover i got used to the lazy convenience of parking sensors,you make it look easy enough for a sunday morning job,thank you again all the best to you

@Martin-wz2ie 3 жыл бұрын

Found out that if you take off bumper it already has the markings so you just need to make pilot holes then hole saw from out side of the bumper to stop any paint chipping

@meriadeglecadre5315 2 жыл бұрын

On the black trim, better to drill at 80mm instead of 30mm. That will fit like the oem sensors, and as written in one comment, it can be seen on the back of the absorber. On my 2009 EU Fiesta, the reverse wire is the full blue, took me some tries to find it so here is a tip for the viewers. Thanks for this nice and helpful video 👍🏻 though.

@iansmith7929 3 жыл бұрын

Nice video, Ewan.

@rrr...512 Жыл бұрын

Great job.

@maxp918 Жыл бұрын

Quick tip: instead of stripping the wire and soldering, simply use a quick splice wire connector or a T-tap wire connector. Piece of cake - takes a few seconds, looks neat, easy to disconnect, cheap - no wonder some parking sensor kits contain one of these.

@Arg0n01 6 күн бұрын

Honestly i prefer to make small in between looms with terminals so if I ever have to swap it out it's quick conmect.

@lemanlifestyle 3 жыл бұрын

I just bought an original set from a Fiesta ST in my color from eBay. Drilled 29 mm and plugged the sensors in the socket that’s already behind all the Fiesta bumpers haha. Fixed it in forscan and tadaa. Original PDC on the screen and through the speakers

@samfkt 3 жыл бұрын

Does it work if you put an unofficial Android Radio?

@ColinWatters 3 жыл бұрын

Can you tell us was it easy to find the socket?

@sosnorwich 3 жыл бұрын

Hi. Good video, thanks. What is the name of the ridge cutter bit you're using to recess the sensors?

@todotvstreaming Жыл бұрын

Is this an aftermarket kit? Did it affect any of your assistance sensors like blind spot or cross traffic warning?

@sneakzi1426 2 жыл бұрын

Hey Ewan, great video! Is there a way to add sensors and also have it so you get a visual display on the small screen?

@Arg0n01 6 күн бұрын

There are kits with the screen. If you have an aftermarket infotainment and head unit you can wire those in the infotainment system.

@paul-ne1bh 3 жыл бұрын

hello ewan are they any good you maid it look so simple good vid thanks

@ewanwillis8514 3 жыл бұрын

Haha I used to work at Ford so I have done hundreds of these. They are a very good upgrade, and will increase the cars value so I definitely recommend 👍

@paul-ne1bh 3 жыл бұрын

@@ewanwillis8514 MANY THANKS PAUL

@allianceofvengeance 3 ай бұрын

Hey can you do this with a 2022+ Ford Maverick? I never knew it didn't come with the truck except for the Lariat models -__- wasted money on the XTL Luxury package thinking it would come with it.

@FernandoSilva_1971 5 ай бұрын

great job! what's name the first driil?

@adambenson732 Жыл бұрын

Does that speaker connect to your car speakers? If not do u know how you would?

@philgoncalves3076 7 ай бұрын

Hi, I'd love to know what that recess drill bit is called please. I've tried looking up the above but no joy! Thanks

@angelogmuller 3 жыл бұрын

hey my man, thanks for the vid! how did you find out which was the reverse cable? I've got a mondeo 2011 and assume might be the same but want to check it 100% before ripping out.

@ewanwillis8514 3 жыл бұрын

Wiring diagram, or you can use a multimeter, test for 12v on each wire when reverse gear is selected. Hope that helps👍

@σπυρος1980 3 жыл бұрын

Nice video the wiring is the same model 5d or 3d;how long take for this?

@ewanwillis8514 3 жыл бұрын

Took me around an hour👍

@σπυρος1980 3 жыл бұрын

@@ewanwillis8514 end with bumper on the car ;

@Timo-Epis Жыл бұрын

What soldergun do you use?

@smokeyjoe6047 3 жыл бұрын

You say you have fitted loads working at ford, however, My 2018 car has canbus wiring, could you advise me whether you can connect the power from the reversing light wiring as you have shown with no issues

@ewanwillis8514 3 жыл бұрын

It will be the exact same process, it will still have a reverse light wire to the bulb👍 hope that helps

@smokeyjoe6047 3 жыл бұрын

@@ewanwillis8514 thanks

@samfkt 3 жыл бұрын

@@ewanwillis8514 Is there any solution without soldering?

@ewanwillis8514 3 жыл бұрын

@@samfkt The proper way to do it would be soldering. You can buy one cheap but alternatively you can use crimps... just wouldn't be the ideal way👍

@richardl1572 2 жыл бұрын

How did you pass the cables through the inside of the bumper and through the panel inside the boot?

@ishanperusinghe Жыл бұрын

He’s show gromit ( black circles ) in boot floor that have to make a hole in to bring in

@user-yq9lg8pt6i 2 жыл бұрын

Thnx! My bumper stop working and now i can replace it with new

@ryanparry_ 3 жыл бұрын

Why did you fit them to the plastic? I thought they have to go on the metal?

@kierawright5363 3 жыл бұрын

🚘

@gwada97160 3 жыл бұрын

merci bro pour cette video sorry for my english i m french i buy a 8 sensors rear and front i need to connect two cables , one to the rear light (plain blue the same of yours i think) but i need connect another cable to the brake light , do you know the color of the cable ? thanks i have fiesta 2015

@ewanwillis8514 3 жыл бұрын

Why do you need to connect one wire to the brake light? That’s unusual in my experience

@gwada97160 3 жыл бұрын

@@ewanwillis8514 it s good i do thé good conncetion thanks

@stavrosdlk 7 ай бұрын

Can I connect reverse camera in the same cable?

@ansamedia6143 Жыл бұрын

Since you're only tapping into the reverse power wire, realistically these can be installed on any car right?

@Arg0n01 6 күн бұрын

Correct. It will draw power from the reverse light. Same with the reverse camera with led lights. If you wire it in and flip to reverse the leds light up and the dash cam goes into the reverse mode.

@pablo123b 3 жыл бұрын

great video just bought the same car and same colour lol, can you put a link to the corner brackets, the kit and the drill cutters you used cheers

@ewanwillis8514 3 жыл бұрын

I got everything from my local Ford dealership, the sensors are xvision

@jakebellamy-wood9562 3 жыл бұрын

Did you have to activate anything? Or was it already pre activated? Thanks

@ewanwillis8514 3 жыл бұрын

Nope no activation required

@jjmmjj9999 2 жыл бұрын

Activate what? It's powered by the reverse light signal.. Same as connecting to a 12v battery in your bedroom, it'll still function. Talking of, I've just had an idea. Battery charger will be permanent 12v... Install sensors into a driveway tree, push wall etc Power by the battery charger When you reverse up (or drive forward) the 'wall' or 'tree' will beep