This is just the video I needed to fix my friend's motorised head - his attachment had exactly the same issue as you show here. I just wanted to say thank you for a very helpful video.
@techfixPOV2 күн бұрын
Glad it helped
@DetRieckhoff5 күн бұрын
I had exactly the same problem. Your video shows the right hints and helped me to solve it. Thank you!!!
@techfixPOV3 күн бұрын
You're welcome!
@captainghost56104 күн бұрын
The melted part was so hard. I put in hot water 3-4 times. I use its blue brush for apart it, thats more easy. Thanks for the video
@techfixPOV3 күн бұрын
Glad it helped!
@jdmletwory6 ай бұрын
Thanks for the vid. Had the same problem and with the help of you, I could fix the problem
@techfixPOV6 ай бұрын
Glad it helped
@bwkermadecs10 ай бұрын
The end of the brush where it goes into the gear was locked up on mine. Couldn't figure out how to get the brush out until I watched this video. I was able to clean out the gunk and melted plastic so it could spin again. Thanks!
@techfixPOV10 ай бұрын
Glad I could help!
@ql32577 ай бұрын
It works! That part was melted maybe because I used the Max suction for too long. Thank you 😊
@techfixPOV7 ай бұрын
Glad it helped!
@bajrangbalikabhakt57 ай бұрын
@@techfixPOVbro can you pls help .. my Dyson hp04 Air fan is showing a white screen after I connected it to app it suddenly stopped when I turned it on again it's showing a white display that blinks over and over .
@commandmediacorps10 ай бұрын
Worked like a charm. Weak craftsmanship, vac head had only been used a couple of times.. Easy fix. Thanks for the video
@techfixPOV10 ай бұрын
I'm glad it was helpful.
@dalehamlin738310 ай бұрын
Good video thank you.......! Note: I think this is a design flaw on Dyson's part. It should be replaced by the manufacturer under warranty. Most people, seniors etc. will not be able to conduct this repair. Melting plastic of the parts can not possibly be a part of the design..... At least Dyson could replace the gear mechanism under warranty. Doesn't make sense that this problem is the customer's responsibility. Just my humble opinion. Thanks for your video.
@Filin19513 ай бұрын
Спасибо, помогло не сломать щётку😊
@techfixPOV3 ай бұрын
Glad it helped!
@davidrasmussen55375 ай бұрын
Superb video … thank You! 🏁🏁
@techfixPOV5 ай бұрын
Glad you liked it!
@erikortiz79313 ай бұрын
Thank you !
@techfixPOV3 ай бұрын
You're welcome!
@emrekartal9304 ай бұрын
Thanks for teaching me how not to fix it.
@techfixPOV4 ай бұрын
Glad to help
@user-sx4jd4bg5u10 ай бұрын
thanks for this video, the Vacuum Cleaner Drive Belt is gone in mine, the serial number have faded. Is it pioneer rubber belt 134-2m?
@techfixPOV10 ай бұрын
Yes, exactly this type of belt is mounted on the brush.
@kapitanfala5 ай бұрын
Thanks, it helped 💪
@techfixPOV5 ай бұрын
Glad to hear it!
@alessiochemeri20593 ай бұрын
Tyvm... Fixed ❤
@techfixPOV3 ай бұрын
Glad it helped
@daryldsouza83 Жыл бұрын
Thanks this helped a lot
@techfixPOV Жыл бұрын
Glad it helped
@famuhuzo2 ай бұрын
Thanks a lot for the vid. Funny thing is I looked this up because i was unable to open mine - turned out in my case the big wheel fused to the cover! It turned out that the plastic frame holding the wheel even broke from the strain of it being fused. I swear this shit is made to break eventually :
@techfixPOV19 күн бұрын
I had a similar situation, I know what you mean. It's only a matter of time before problems appear.
@avr021020 күн бұрын
what screw bit are you using for the screws?
@techfixPOV20 күн бұрын
Torx T8 screwdriver
@CandisGenglerАй бұрын
My problem is that not only does the brush not turn but I can’t even get it out. I have the little cap off, but can’t get the brush to come loose, even pulling with a vice grips. I have the belt off but can’t go any further without getting at that last screw, since the brush won’t come out. Any suggestions?
@techfixPOV19 күн бұрын
It seems that due to the friction, some components melted and got stuck. I don't think you can separate the central brush except by forced separation. I had a similar situation and the only option was to use a big flat screwdriver as a lever to move the brush away. Good luck!
@CandisGengler7 күн бұрын
@@techfixPOV Thank you. My son did finally manage to get it apart, using force. And then he glued the piece that broke. :) But it works fine now. I’ll clean it more often after this. ;) $50 saved!
@clivebush21488 ай бұрын
good vid but shame not showing the removal of the large cog wheel as I need to replace the whole plastic part as that is what has broken.
@cong7598Ай бұрын
I removed the motor. Now i cant attached it back as the wire is deep in the holder
@ozelmertАй бұрын
Release the wires from the upper side, connect them to motor, tie them with small rope and while placing motor to its place, pull cables up and fit to housing
@cong7598Ай бұрын
@@ozelmert seems like motor is not working anymore
@diogochambel1510 ай бұрын
My issue is that the motor is not spinning at all… my guess is that one of the connectors might be loose, but I don’t know how to reach the back of the motor
@techfixPOV10 ай бұрын
The assembly containing the mechanism must be completely dismantled. The whole mechanism is fixed to the motor with two screws.
@EmreMat Жыл бұрын
My dyson laser not working.
@techfixPOV Жыл бұрын
I haven't worked on a laser brush yet, but if you tell me what the problem is, maybe I can help you. Does the brush not spin? Does the laser work?
@EmreMat Жыл бұрын
@@techfixPOV only the laser light is not working. From day one.
@techfixPOV Жыл бұрын
Try to switch the button on the brush several times while the brush is working. If it does not show any sign that it lights up, it is possible that the problem is with: the laser diode, the voltage regulator, the laser diode current control module. I will try to disassemble such a brush and I will return with a link here.
@EmreMat Жыл бұрын
@@techfixPOV The laser light has not been on since the first day I bought it. I have set the button many times, but no result. Dyson sent me a new one. the broken sweeper remained with me. Thanks for ansvers.