I was getting error code and the sudden of the washer wasn't working during the load. I have to restart the washer for drain and spin.one day we fixed the error code by cleaning the drain pump filter.
Пікірлер: 30
@CosMcOldDude3 жыл бұрын
Love you, man! You could give a little more information on how to remove the back panel and how to reinstall the filter plug but this worked great. Thanks so much.
@russpirie15923 жыл бұрын
Thank-you. ALL of my work clothes were in the washer. It is now working fine. Thanks so much!
@jaychenn36193 жыл бұрын
Worked great for me! Thanks Don! Warning: Some of the edges on the sheet metal back panel are sharp. Found that out the hard way.
@QueBeraBera3 жыл бұрын
OMG ME TOO sliced the F out of all of my fingers and thumbs before I even felt it...bleeding all over the inside other washer ack!!!
@lmnewyork3 жыл бұрын
Thank you so much! You saved me hundreds of dollars in repair fees!
@Correiajc Жыл бұрын
Thanks brother that was my last video before spending money.thanks again
@TheHelicapt Жыл бұрын
Was that a worm that fell out of the filter ??
@KunouJS3 жыл бұрын
Thank you. We were expecting a bunch of junk coming out like in the video. But it turns out that there was a big coin on that filter.
@russpirie15923 жыл бұрын
Beat you. We had 4 coins (and a tiny screw).
@MrTwisterdc2 жыл бұрын
Yep, found 2 nickels... Works fine now. Thanks!!!
@gsandova113 жыл бұрын
Thank you, that seemed to have done the trick. There was some lint debris but not enough in my mind to cause an issue. Nevertheless, the error cleared up. That filter really stunk! Don't forget to do diagnostic mode just as Todd Heath instructed.
@benhudelson3 жыл бұрын
This worked perfectly! Now I just need to tell my family not to put muddy rugs in the washer! (Shame on Whirlpool for making that filter so inaccessible!)
@RycheForOrder3 жыл бұрын
They have addressed that issue. Most all newer models have pump filter access.
@smp222 жыл бұрын
lol! nice video. Yeah, removing that sock from the drain aughta do it!
@jonathanmarbury3273 жыл бұрын
This fixes f1 e9 error codes. NOT f1 error Just a heads up for everyone who finds this video
@jonathanmarbury3273 жыл бұрын
Does not fix f1 e3*
@leslifranco66984 жыл бұрын
How you restart the washer, I can't open it, my clothes still inside of it.
@karinjanotka75313 жыл бұрын
Unplug. Take off the top. Some with a long arm reach into the top of the right side of machine towards front by door latch. There is a pull to open door.
@kramnull89623 жыл бұрын
There are 3 holes behind the rubber seal at the bottom of the doorway opening. Those need to be cleaned as well. They drain any water splashed up on the door during the cycle. Perhaps act as a vent as well.
@kennorr123 жыл бұрын
Cleaned filter E1F3 code did not clear. Any other options?
@kramnull89623 жыл бұрын
Unhook your water lines, and check the filters that are in your water inlet tubes. I had to take a small pair of pliers and pull them out. The hot water side was clogged with crusty rusty dirt. I cleaned it with water and it has been working properly for 3 weeks; after over a year of fighting with this error code thing...
@morrisfam112 жыл бұрын
Didnt work. Drain was clean. Had run the clean cycle a week or so and when I went to use it the code came up and the door is locked. Does not respond to anything. What next?
@nwmi4932 жыл бұрын
i have the same piece of shit machine too. still fight with error on a weekly basis. remove top, manually unlock door by pulling release ring. u will see it down there. power off machine. press 'wash/temp' 'spin' and soil' buttons three times in that order. machine will sound. hold soil button 7 seconds. machine will sound. unplug machine, wait 10 seconds for power to leave completely. plug back in and begin normal operation.
@toddheath94704 жыл бұрын
Quicker way is to tilt back washer, remove 2 nuts on bottom panel and you have instant access to the drain pump filter. The nuts are torx bit t20 I believe or 1/4 in hex socket will work. Also after removing and reinstalling the filter do a Diagnostic test to reset washer. DO THIS EXACTLY to go into diagnostic mode... temperature, soil level, spin speed...3 times in rapid succession and you should be in that mode. It should unlock door and reset codes...good luck
@huskerdave30434 жыл бұрын
Todd Heath do you need to lay the washer all the way over on the back?
@kramnull89623 жыл бұрын
Actually you need to lean the washer forwards, and get it to drain the pump and everything. Tilting back pushes the water/trash back into the pump...
@kennorr123 жыл бұрын
Cleaned filter. E1F3 did not clear. Any other ideas?