How to fix the Lancer ignition switch

Рет қаралды 32,509

3 жыл бұрын

Cleaning and fixing the ignition switch of a mitsubishi lancer 2006.
طريقة تنظيف واصلاح فيبرة الكونتاكت لعربية لانسر بومة 2006

Пікірлер: 27

@fookutube501 9 ай бұрын

YEEEEEEEEAAH ,nearly 2 years trying to figure out how to fix my starting problem when I open my ingition it was dirty asf....

@guillermoblanco4060 8 ай бұрын

Thanks a lot. now i have an idea how to fix my lancer too.

@PedroSilva-bx7ii 2 жыл бұрын

Hello, tanks for this video I have exactly the same problem, I will try too fix it. 👍👍

@mtrltoolman 3 жыл бұрын

احسنت جزاك الله خير.

@davidshaw4727 Жыл бұрын

Thanks for your help, good guidance.

@amaldonador69 Жыл бұрын

Thanks for your help

@jjoey30 Жыл бұрын

The problem is the brass plate wear down on contact thats y its not starting

@DanielAlvarezMaldonado Жыл бұрын

Thanks

@ibalaa1085 2 жыл бұрын

احسنت

@natureloverbee8629 2 жыл бұрын

Thanks allot, you saved mine $ 30. Love from Pakistan

@danishawan6514 Жыл бұрын

Where did you find the starter in Pakistan? I am from rawalpindi, looking for parts of lancer 2007

@paoloyanutzzi1419 Жыл бұрын

Gracias, me acabas de ahorrar 35 $ que es el valor actual de uno nuevo, aqui en Venezuela el sueldo es de 7 $ Mensuales.

@pyen3526 Жыл бұрын

What if when it’s in accessory the lights on the dash turn on but when you turn it to on right before you crank it the lights come off, I want to say it’s a weak power output from the battery as in maybe my ground terminal is corroded

@joellajuett1060 Жыл бұрын

I may have same issue. 2006 Mitsubishi Lancer 2.0 SITUATION: When I was backing while turning the car stalled and would not start. Acted like dead battery or bad starter. I pulled starter and tested fine 3x at 3 different testing locations. Battery has full charge. When I turn key same thing bendix sounds to be kicking out and engaging but engine not turning. Tried multiple times and ground on battery starts to get hot. In the past I did have an issue with relay block under hood had come unmoored and fell near front tire and was collecting water and debris. Eventually the connections failed and I replaced entire block. I soldered all connections and heat shrinks over each one (retested today and all connections are good) QUESTION: I understand if the car went start it may be that part in colum, but If the part your replacing in colum was my problem would it cause the car to stall. Also if that part fails will it allow starter to start to work but not completely? Any help greatly appreciated

@kadeemconnor8923 Жыл бұрын

Hi my cs2 lancer turning the key but no start not even a click is it the starter or the key switch

@jestark0890 Жыл бұрын

Hi Sir, what grease or oil did you use for final coating of the contacts?

@elBendary Жыл бұрын

Vaseline or any white grease

@teresahobbs2254 Жыл бұрын

My car has a similar issue but I can get it to start if I push the key in really hard as I turn it. Do you think it's the ignition switch or the cylinder switch?

@elBendary Жыл бұрын

I think it's the ignition switch

@jamiestonham Жыл бұрын

What was the stuff you were dipping the cotton buds in to wipe the black part of the switch?

@elBendary Жыл бұрын

white grease

@kicksoffs Жыл бұрын

did you hear a clicking sound when you tried starting it or heard nothing cause i hear a clicking sound.

@elBendary Жыл бұрын

Heard nothing when tried starting

@kicksoffs Жыл бұрын

@@elBendary thanks

@Propa_Way 9 ай бұрын

@@kicksoffsthat’s usually a starter problem when it’s clicking

@majdez6707 Жыл бұрын

اخي انا عندي لانسر 2001 وتعطل عندي القطعة اللي انتا الان تقوم باصلاحها وخايف اطلب القطعة من برا وتكون مش بتركب على سيارتي اتمنى لو تعطينا رقم القطعة بالضبط وهذا رقم شاصي سيارتي JE3DB36C61U771422