the clearance for both the intake and the exhaust is .006
Пікірлер: 31
@robertbobin5053Ай бұрын
My pappy done learned me the differ tween timing inspection, and valve covers. Yeehaw!
@clarencesnyderjr95477 жыл бұрын
Thanks for the advice. I just fired it up got it running I had a feeling it would start I even put the seat on
@23ducksunlimited7 жыл бұрын
thanks for the video man!
@TheHondaOutlaw7 жыл бұрын
no problem im open to any suggestions for future vids too
@heresthething....46855 жыл бұрын
A stationary camera viewpoint would help me if you're only working on one area of the bike. I was getting seasick after a short while. Great video content though. Thanks.
@galliogarcia3 жыл бұрын
Hey so I was taking out the plug that it suppose suppose show a T and it stripped... is there a solution?
@MyLifeThai3719 ай бұрын
Your supposed to use an "impact screwdriver" from harbor freight to remove aluminum plugs from honda atvs. The impact screwdriver is $2.99 at harbor freight. You hit it with a hammer, while twisting it.
@backwatersandbackroads5 жыл бұрын
Very helpful,) thanks
@jasongodin71654 ай бұрын
Need to hold screw when tightening nut or it will turn
@trigerakaem33113 жыл бұрын
There called a Feeler Gauge
@cruz_engbring74883 жыл бұрын
Feuler not feeler
@timmyandtrisha5 жыл бұрын
What is the best way to get up with you to ask a question
@gabe53602 жыл бұрын
Better make sure you’re on the compression stroke of TDC, if you’re not you’ll screw yourself 👀
@TheHondaOutlaw2 жыл бұрын
Doesn't hurt anything it's very obvious when it's done wrong it rattles like crazy. Simply do it again the right way this time.
@ethankarr10517 жыл бұрын
+TheHondaOutlaw what happens when you dont ajust those
@TheHondaOutlaw7 жыл бұрын
for the most part not a whole lot but if it goes way to long it will eventually get hard to start or just wont start at all i had one that did that to me one time
@clarencesnyderjr95477 жыл бұрын
Someone put sugar in my gas tank, and seized the valve to the exhaust which cause it to not fire right. So I cleaned the burnt sugar off the piston and and cleaned the valves, and replaced the valve that was damaged after I put it all together I put the timing on the T, and the timing chain with the rockers down, but after putting everything on it won't start. Got any advice for me?
@TheHondaOutlaw7 жыл бұрын
you probably dont have much compression if there was sugar in your tank also you may not be getting spark
@clarencesnyderjr95477 жыл бұрын
TheHondaOutlaw it has a spark I got to check if there is compression
@jimrowdy93133 жыл бұрын
So I did this and they still tick how do I know if I'm on the right stroke
@matthewtaylor40793 жыл бұрын
Your cam might be bad
@noslacking19454 жыл бұрын
Mine runs hot and dies after I run it and stop at idle pls help
@MyLifeThai3719 ай бұрын
Wash the mud out of the cooling fins.
@papichulo46974 жыл бұрын
what’s ur email i have a question about my honda fourtrax
@ethankarr10517 жыл бұрын
all mine fire up quick like i dont even hold down the start button just one push
@TheHondaOutlaw7 жыл бұрын
so did this one but they still needed adjusted
@ethankarr10517 жыл бұрын
TheHondaOutlaw i geuss ill get to checking when i find the time i pretty much dont ride my 300s any more tho because i bought a new 420
@TheHondaOutlaw7 жыл бұрын
i dont get to ride because of my work schedule and the lack of places to ride around here
@MyLifeThai3719 ай бұрын
@@TheHondaOutlaw Section lines.
@MyLifeThai3719 ай бұрын
@@ethankarr1051 I bought my 420 brand new in 2008. That was a game changer, since it starts right up at 0 degrees out and can play in the snow in 3rd gear. I also bought a 2006 350 Rancher brand new and that thing needed a diesel torpedo heater to start it in the winter. Our Honda 300 starts good during the winter.