How to hook up air lines on an 18speed Eaton fuller transmission. Shift knob replacement.

Рет қаралды 22,545

ETR Truck Center | Engine & DriveTrain Specialist

Жыл бұрын

This is a video on how to plumb in a shift knob to an Eaton fuller heavy duty 18 speed. You will see in the video this is a very easy job to do. You don’t have to worry about getting your air lines crossed up anymore if you follow these instructions. ‪@etrtruckcenterenginedrivet8918‬
We hope this video helps someone thank you guys and girls for watching have a great day👍

Пікірлер: 27

@notchfox6086 Жыл бұрын

Thanks for the video sir!

@etrtruckcenterenginedrivet8918 Жыл бұрын

No worries! Thank for watching

@carlosrivas4503 4 ай бұрын

Thank you sir very good!!

@butchmcintyre5196 Жыл бұрын

thank you for the help

@etrtruckcenterenginedrivet8918 Жыл бұрын

Thanks for the comment and thanks for watching Butch👍

@SecretSex Жыл бұрын

Very good movie !

@etrtruckcenterenginedrivet8918 Жыл бұрын

Thank you

@jimpickens5682 Жыл бұрын

took one of these apart and put it back together in college.

@mattkuhar9743 7 ай бұрын

Stupid question, When you flip the lever is it applying pressure, and when you flip back it lets the air pressure out? (same question about the switch) I am planning to run this exact shift knob in my wrangler if I can run the air lockers with the lever and switch :)

@TrucNguyen-ns3hn Жыл бұрын

i like transmission truck u.s

@jht09 Жыл бұрын

I got a great question is an 18 speed built from a 9 or a 13 speed the same as a 18 or is there a difference and is one better than the other thanks a bunch would love to see a build video can’t wait to watch the other videos you have on your channel

@onebadapple83 Жыл бұрын

Hey ETR! Just found your channel….Great videos especially the one towing with the driveshaft connected! How ‘bout one on the transmission grinding noise at low RPM and low speed? 3rd gear is the worst.

@etrtruckcenterenginedrivet8918 Жыл бұрын

Would love to do a vid on it. Is the sound kind of high pitched like a whine?

@Dachamp2001 Жыл бұрын

I literally just came across your channel. Been trucking 23yrs always wondered how the knob hooks up. Out of curiosity whats the other holes for one knob valve?

@JonathanAbrea 3 ай бұрын

Have a lik in a shiptnob if you can the splitter,

@scraphaulin Жыл бұрын

Question: what if I wanted to run my switches of pneumatic toggle switches mounted elsewhere....what type of switches would be needed and how would the lines be connected?

@Jreddygo Жыл бұрын

I have a 10 speed and I want to extend or raise my shifter shaft would I have to change those red and black lines or just buy adapters to make them longer? Also what size lines are those and where can I buy those particular lines at? Thanks

@laynejohnson6424 Жыл бұрын

What if it doesn't shift from hi to low like that

@DaddyForeverYess 11 ай бұрын

Roger that…Ive got an 18 speed that occasionally fails to split the gear. The owner operator has seen where the air lines get gummed up. We are going to attempt to disconnect air lines and run brake clean and air through them. Thank you for your insight. Any additional suggestions welcome.

@etrtruckcenterenginedrivet8918 11 ай бұрын

I would start with checking the splitter cylinder itself. It may have rust buildup causing poor shifting.

@DaddyForeverYess 11 ай бұрын

@@etrtruckcenterenginedrivet8918 Copy

@jorsot8839 Жыл бұрын

Question replaced the clotch had trans check at a shop. I n a friend installed the clotch and trans but when I test drove it don’t want to go on height gear. Only up to 4th. Any idea of what to check is a 18 speed

@etrtruckcenterenginedrivet8918 Жыл бұрын

I am assuming that you have watched this video and are now absolutely sure you have the air lines plumed in correctly? If so did this truck have this issue before you pulled the clutch? If the transmission has just now started with the issue you mentioned you probably have an issue with how the top plate was installed. The slave valve on the side of the transmission has an actuator that works along with the top plate. If during inspection when the top plate is installed if things are not lined up correctly you can bend the actuator and you will not be able to range shift.

@jorsot8839 Жыл бұрын

@@etrtruckcenterenginedrivet8918 yea I’m going to check the hose because I didn’t hear a loud noise when flipping the switch also it did not have any transmission problems before they took it apart