How To Install A Crankshaft - Burnout Tutorials (Rebuilding the Chevy 350)

Рет қаралды 6,802

3 жыл бұрын

In this video, Ryan takes you through the process of installing a crankshaft in an engine. He's working on rebuilding this small block Chevy 350 which he pulled out of his 1976 Chevy Camaro. If you want to know more about his Camaro, The Banana Peel, check out Episode 5 of Burnout: • I Bought My Dream Car,...
Subscribe: bit.ly/3vVJiWE
Follow us-
Instagram: @burnoutshow
/ burnoutshow
Tik Tok: @burnoutshow
www.tiktok.com/@burnoutshow?l...
Facebook: @BurnoutShowNE
BurnoutShowN...
Our Website:
www.burnoutshow.com
Sponsored by:
Up and Social - Boston Web Designer
GoPro
Pit Posse Motorsports
FNX Fitness
Burnout Animation Created By Nicholas Major

Пікірлер: 19

@robc3863 3 жыл бұрын

Great video for first timers like me! Cheers!

@richardfabian7946 3 жыл бұрын

You are a god send. I dont know how your channel isnt blowing up

@TheBurnoutShow 3 жыл бұрын

Best compliment I’ve ever received. Thank you.

@Skyler_Hagen 11 ай бұрын

It’s a good idea to pry the crankshaft all the way forward and all the way backward once when the rear main bearing cap bolts are snug but before torquing them. This makes sure the bearing thrust surfaces are pushed into the same plane with each other instead of one being slightly offset. Even though the bearings fit tightly into the cap, the only thing aligning the cap forward and rearward is the loose fit of the bolts inside the cap holes. It’s possible for them to not be aligned unless you force them into alignment before torquing down and clamping it in place.

@user-xh5mz6bb1p 10 ай бұрын

Nice explanation

@wiley1341 4 ай бұрын

Great Video thank you Im curious why bearing clearance wasn't mentioned or talked about. using Plastigage ?

@TheBurnoutShow 4 ай бұрын

We have a whole separate video about that in the series playlist. Here’s the link to the video: How To Use Plastigage To Measure Your Crankshaft Main Bearing Oil Clearances - Burnout Tutorials kzfaq.info/get/bejne/gJqVgNmCvbWVqaM.html

@nevbud3262 9 ай бұрын

great video i am planning to build one as well, only its a 305, question about the crankshaft i've got a new one from te box do i need to balance this on or can i start building. block is bored over 0.030 . everything will be new on it only the piston arms are beeing used again and the crankshaft bearings. so if any one can advise i woult be glad.

@joeclark9042 Жыл бұрын

Very good video bud first time I seen it so just let you know very good can I ask you a question where did you get that crank and bolts at is that a stock crank if you could please give me some information on it I'd really appreciate it I have a 350 four bolt main that I'm going to do about a minute on So if you could please let me know thank you very much

@TheBurnoutShow Жыл бұрын

I got this exact bottom end kit from Summit Racing. This one isn't available at the moment, but you can find one similar that will work. They have tons of options at Summit. If you're also looking for a top end kit or anything else let me know and I can recommend the stuff that I got myself.

@coophewitt4367 3 жыл бұрын

I was in the process of rebuilding my 1943 Ford bronco with a 2019 Nissan Altima engine, my crankshaft was giving me a hard time though. Good tutorial

@TheBurnoutShow 3 жыл бұрын

Anytime bro bro!

@Skyler_Hagen 11 ай бұрын

1943 Bronco eh?

@rayarnold9390 6 ай бұрын

I had my chvey 350 rebuilt no when I try to start it the starter grinds . I replaced starter and flywheel . The only thing I could think of is a warped crank. What's your thoughts.. ty

@TheBurnoutShow 6 ай бұрын

Hard to say without actually seeing it or hearing it, but sometimes if you accidentally flip the wires on the solenoid then the starter doesn’t fully engage with the flexplate.

@steelcitycaprice.899 Жыл бұрын

👍🏾😎🏁🏁🏁

@robc3863 3 жыл бұрын

I'm rebuilding a 350, single rear seal, I bought a new timing chain and gears from Summit Racing, they recommended an Edelbrock 7802, but when it arrived the main cog has a smaller diameter and the chain looks lighter. Do you think it's the correct one? www.summitracing.com/parts/EDL-7802

@TheBurnoutShow 3 жыл бұрын

Yep. It looks good to me. The larger gear bolts on to the front of the camshaft, and the inner diameter of the hole doesn't really matter because nothing goes through it. Whereas the smaller gear goes on the crankshaft, so that hole has to fit over the shaft sticking out of the front of the crankshaft. The chain should be perfectly fine as well.

@robc3863 3 жыл бұрын

@@TheBurnoutShow The diameter of both cogs is about 25% smaller, but I guess it's the proportion that's important to keep the sync. Chain is also much lighter than the original.