HOW TO INSTALL A SUBFLOOR ON CONCRETE

  Рет қаралды 888,963

Simpson Properties

Simpson Properties

Күн бұрын

Tools Required:
- Drill with a hammer setting (SDS drill works best)
- Impact gun and Phillips bit
- 3/16" Concrete bit
- Scissors
- Hammer
- Taping block (scrap piece of 2" x 4")
- Shop vacuum
Materials:
- Delta-FL (105 sq ft roll)
- Landscape Fabric
- 4' x 8' Sheet of 5/8" OSB with tongue and groove
- 100% Clear silicone
- Tuck tape
- 1/4" x 1-3/4" Phillips flat top Tapcon screws (approximately 8 per 4 'x 8' sheet)
Laminate Floor: Life Stepp, country collection, colour: Gray Smoke, Size: 1215x126x12.3mm, SKU # 2717. Each box covers 19.77 sq ft.
Delta-FL in conjunction with 5/8" OSB tongue and groove plywood is the perfect subfloor system for concrete and slab on grade floors. The plastic membrane is installed with the dimples down to create a 5/16"thick air space allowing the concrete slab to breathe. If there ever was a flood it would also allow the water to flow freely towards any drains. By installing this subfloor you will increase your floor temperature by 7 °C providing a warm and comfortable basement floor.
Music Credit:
Electro-Light - Symbolism [NCS Release]
Song Link: • Electro-Light - Symbol...
Time Codes
0:00 - Intro
0:53 - Landscape fabric
1:37 - Delta-FL Taping Seams
3:38 - Installing OSB subfloor
5:32 - Installing concrete fasteners
7:23 - Outro

Пікірлер: 1 100
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Intro: 0:30 Landscape Fabric: 0:53 Delta-Fl Taping Seams: 1:37 Installing Wood Subfloor: 3:38 Installing Tapcons: 5:32 Outro: 7:23
@andyzankowicz1802
@andyzankowicz1802 3 жыл бұрын
Thanks for this very well explained video. I’m doing every step as per the video but I am finding the screws are not going in flush. Are there differences in strength of impact drivers. Mine works great until the last 3mm. Very frustarting
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
@@andyzankowicz1802 you may not be drilling the holes deep enough. Also, it will help if you back out the screw when it starts to bind. Then screw it back in feathering the trigger. When you back out the screw it helps remove any concrete particles that are binding.
@falsealarmno
@falsealarmno 2 жыл бұрын
Why didn't you put the Delta underlayment underneath the wall stud plate? It stops at the wall.
@simpsonpropertiesltd
@simpsonpropertiesltd Жыл бұрын
@@falsealarmno I had my framing done already. You can install it underneath the framing. It's a better method to have the Delta-FL beneath non load bearing walls IMO.
@SexyEarHole
@SexyEarHole 3 жыл бұрын
I've been watching videos on doing this exact thing for two days now. FINALLY, I've found the one that explains exactly what I need to know, and in language I can understand (as a DIY'er). THANK YOU!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
That’s what this YT channel is about. Simplifying the construction process so that anyone can understand the process. Thanks for your support it’s much appreciated.
@petemiller519
@petemiller519 3 жыл бұрын
Nicely done! I am a retired structural engineer and wish all contractors would have your conviction and dedication to detail. Cheers from Canada.
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
I’m Canadian as well! I appreciate the feedback. Thanks for watching.
@stevenmorrison9446
@stevenmorrison9446 7 жыл бұрын
Thanks for taking the time to put together such a great and informative video. It's answered questions I previously couldn't get answered about the sub floor from suppliers here in the UK.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Steven Morrison thanks! That's exactly why I created this KZfaq channel help people like yourself. Thanks for the support.
@greatnationnow
@greatnationnow 7 жыл бұрын
Great work! Thanks for being so thorough, and slow enough for people to listen to! Room looks super nice! I may do our basement with the same colors!
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
greatnationnow thanks! I purchased the paint from Benjamin Moore. Here are the colour codes HC-166 Kendall Charcoal and 2112-70 American White.
@kevinbeamer8161
@kevinbeamer8161 3 жыл бұрын
Great video and thanks for landscape fabric tip. TY for sharing. Ideally, Delta-FL / OSB T&G is installed onto slab before non-load bearing walls are built. Then, for exterior walls, frame them ~1" from the foundation wall and create vapor barrier with closed-cell spray foam. This method provides an ideal transition from the subfloor underlayment to the poured concrete foundation wall.
@eyeofthetiger7
@eyeofthetiger7 8 жыл бұрын
This guy knows what he's doing. Great work and thanks for the information!
@simpsonpropertiesltd
@simpsonpropertiesltd 8 жыл бұрын
Thanks for the positive feedback! Make sure to subscribe to my channel I will be posting a lot more videos. I'll be documenting my next build from beginning to end.
@stuartdicks2082
@stuartdicks2082 3 жыл бұрын
I am trying to put a floor in a house in spain it has rising damp in the walls, and was interested what youd suggest?
@user-vz1jl8qg9b
@user-vz1jl8qg9b 2 жыл бұрын
@@stuartdicks2082 젻사 듀엣 ㅠ 모두 ㅐㅅ ㅓ
@user-vz1jl8qg9b
@user-vz1jl8qg9b 2 жыл бұрын
@@simpsonpropertiesltd 컫유
@samtour8545
@samtour8545 3 жыл бұрын
Very refreshing to see a pro at work giving instructions and not trying to sell you something. Thanks a lot sir
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
It’s fun to share knowledge so that others can apply it to their projects. Thanks.
@sylvandaugert6203
@sylvandaugert6203 3 жыл бұрын
I like that you put silicone in the screw hole for vapour barrier continuity. A small detail that I haven't seen others do. Nice work.
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks. It’s all about the small details.
@mikefreeman3772
@mikefreeman3772 4 жыл бұрын
This is a great video regarding install of wood sub-floor on concrete basement floor. The main problem I see is, is that very few builders can properly dig & install basement structures using proper site prep., and drainage (my sub-contractor experiences). It's refreshing to see someone (this guy) doing a job correctly. I hope he stays busy and makes good profits.
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
Thanks Mike! I am more than busy haha working on my own projects for the most part.
@stormbytes
@stormbytes 5 жыл бұрын
Best darn video about subfloors and underlayment installation I've seen to date. Great job. Very helpful. Thank you!
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks for the feedback! It’s much appreciated.
@vanamaladutt6711
@vanamaladutt6711 3 жыл бұрын
i am in the process of removing asbestos tiles and mastic and then I am going to prep the floors for new tiles.Reading and watching everything that I come across. You are the best!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks for the feedback. It’s greatly appreciated 🙌🏽
@CoffeeAndAViewdotcom
@CoffeeAndAViewdotcom 5 жыл бұрын
I just told someone yesterday, I thought this would work.. and you proved it.. awesome. Thank you... very cost effective.
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Awesome! I’m glad you found the video helpful.
@AkinaGod
@AkinaGod 4 жыл бұрын
Is the landscaping fabric felt or the plastic kind? And why do I see people putting the vapor barrier above the plywood sometimes? Which way is correct?
@Musicmannstudios
@Musicmannstudios Жыл бұрын
Excellent video, my friend. Honesty, tips, and knowledge. I've been researching this for several weeks and you somehow explained all my concerns in 1 8 minute video. Again, excellent work. I'm going to do the sub floor first, then line the block wall with 1" foam board (for R value and vapor barrier) then build the walls on top of the sub floor. The additional tuck tape around the perimeter where the foam board meets the subfloor may be overkill for my build, but we ain't come this far...
@simpsonpropertiesltd
@simpsonpropertiesltd Жыл бұрын
Thanks for your kind words. It’s great to see that a video I made years ago is still helpful to people working on their projects. You have a great plan in place. Here is a great resource on insulating basements that you might find helpful: www.buildingscience.com/documents/information-sheets/basement-insulation Best of luck on your project!
@yn9861
@yn9861 6 ай бұрын
I could never find a contractor that would care this much
@simpsonpropertiesltd
@simpsonpropertiesltd 5 ай бұрын
They are out there! Keep looking.
@kristopherdetar4346
@kristopherdetar4346 3 жыл бұрын
Excellent instruction and calm voice with no fluff. Keep up the great work young man !!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks!
@lucasmccann6726
@lucasmccann6726 6 жыл бұрын
Thanks a lot for posting. I think there's some great advice in here. So happy to live in the age of "free information"
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks Lucas! I agree, we live in an amazing time with an abundance of information at our fingertips.
@lucasmccann6726
@lucasmccann6726 6 жыл бұрын
Just finished my floor install two weeks ago using this method in my detached garage. Feels great and Im very happy with it
@EazyT8439
@EazyT8439 6 жыл бұрын
Good job buddy great vid. I’ve been in construction for 17 years and I just nod my head when I see diy’s leaving Home Depot with three buggy’s of those 2 by 2 panels such a rip off, for my basement I actually used foundation membrane with the landscaping cloth already attached, as I got it for free from work. Again good job on showing ppl how to save their hard earned money.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks! You have to be careful using the foundation wrap for a subfloor application. It is manufactured with different plastics and generally not built as stiff as the Delta-FL.
@loriperkins8331
@loriperkins8331 7 жыл бұрын
Thank you for a very informative video! Apprecaite your camera person too. I did not get a headache from the camera moving too fast and all over the place like many you tube videos that are posted. Keep up the great work!
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Lori Perkins thank you so much! I really appreciate the feedback. It was my wife that filmed this I'll be sure to pass on your kind words.
@alderaz7049
@alderaz7049 4 жыл бұрын
Perfectly done perfectly explained you even moved the silicone away from the top of the screw.
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
Thanks!
@billknows1980
@billknows1980 6 жыл бұрын
I am a teacher trainer and looking at this video and assessing the teaching skills, well I would definitely give 10 out of ten to you, perfect, clear, and simple!
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks Bill! Your feedback is appreciated.
@learnbangla5732
@learnbangla5732 7 жыл бұрын
What a nice, elaborate and precise how-to video! Thank you very much.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Learn Bangla thanks for the positive feedback and subscribing!
@learnbangla5732
@learnbangla5732 7 жыл бұрын
Hi, How much height did you loose in total? I understand the OSBs are 5/8. Thanks.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Learn Bangla Delta-Fl is 5/16" + 5/8" OSB = 15/16". It's almost 1" in total.
@sancop
@sancop 5 жыл бұрын
Hi. I found your video because our project is going to be over our house floor (not basement). We are looking for an affordable option bc we bought an approximately 5,000+ sq ft slaughterhouse (yea, I know), and it’s all uneven concrete flooring with drains. We attempted to level them about 12 years ago and made it worse. Since then, it’s been a hurry up and wait, trying to find the answer. I think your video could be the right answer since it appears to be forgiving and affordable. We live in NW Florida with LOTS of humidity and rain and have an inground pool. Do you think this would be a feasible option for us!!??
@sancop
@sancop 5 жыл бұрын
PS, we are diy-ers (fortunately or unfortunately?!?!)
@LetsDoMath
@LetsDoMath 7 жыл бұрын
I used Delta FL on the basement subfloor I designed 9 years ago. The Delta FL installation specs say do as you are doing here, and put the plywood directly on top of that. I did something a bit different. Mike Holmes goes on about the benefits of a thermal break. He installs rigid foam direct to the concrete. That's going to sweat, as concrete lets moisture come up as well as go down. Hence the need for the Delta FL. But on top of that, you'll get a vastly better floor if you install a thermal break. I put in 1" codeboard. That's R5 all over the floor. The thermal break works to keep a very stable temperature in your basement. It will cost more than what you're doing here, but the end result will be a floor that's so much nicer to have your feet on. And it will give you savings on your heating. If your basement is properly insulated, you'll go from sitting on top of a cold space in the main house, to sitting over a warm space. It turns out to be integral to the house's temperature and your bank balance.
@lionintu
@lionintu 6 жыл бұрын
LadyDMcollector thanks for the I fo. What is the order or materials on your cement floor, and combined thickness?
@cristiancampo8133
@cristiancampo8133 6 жыл бұрын
LadyDMcollector when you talk about 1” codeboard for thermal break are you referring to the R5 pink panther foam insulation?
@gomerpyle1886
@gomerpyle1886 6 жыл бұрын
LadyDMcollector Hello did you put the osb over the codebord ? Thanks Rich
@gomerpyle1886
@gomerpyle1886 6 жыл бұрын
Hello is it better to use a concrete sealer first?Will that fabric cause moisture?You are very helpful Thanks Rich
@mikecampanella1990
@mikecampanella1990 6 жыл бұрын
Vic da G hey there, the order of the flooring is a subfloor like the delta, or dmx roll out stuff, then 1"of closed cell foam board, then the plywood subfloor. You can even do a tongue and groove floating subfloor and have the pieces connected with small strapping on the edges. Then frame in the basement walls and it'll keep everything from ever shifting. Now you've got a fully sealed vapor barrier without a million holes in it for tapcon screws. You've got a nice thermal break and energy saving floor and a dry and warm basement.
@jimmy4111
@jimmy4111 3 жыл бұрын
This video helped me a lot!!! Had to order the landscape fabric on the internet because of winter time in Canada, but I feel like it was worth it! Thanks you so much!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks for the feedback Jimmy it’s much appreciated. I’m glad you found the video helpful. It’s a smart move installing the landscape fabric IMO. Good luck on your project.
@peterolejar1061
@peterolejar1061 7 жыл бұрын
Hello guys, looks like this method is very simple and I love the landscaping fabric idea, I will definitely try this in our basement...
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Peter Olejar that's great to hear! Let me know how your install goes.
@fredmario9450
@fredmario9450 6 жыл бұрын
I really liked your job am convinced another member on board 👌🏻👍🏻
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks for the kind words 👌🏽
@maguiregrouprealestate1427
@maguiregrouprealestate1427 6 жыл бұрын
Great video. This solidified my basement flooring plan. Kudos to camera person.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks! It was my wife that shot the video. I will be sure to pass on the message. Good luck with your project.
@bethyaeger2518
@bethyaeger2518 6 жыл бұрын
Thanks Dude! So nice to see how its done and done right! BEAUTIFUL JOB!
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks!! I really appreciate it.
@sablagedeplancher2507
@sablagedeplancher2507 6 жыл бұрын
Very informative video. Thanks for the info.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks I’m glad you found it helpful!
@LetsDoMath
@LetsDoMath 7 жыл бұрын
There is an addendum to this though. A few weeks ago we had a small basement flood. The ground was saturated and it rained all night. We came down in the morning and there was a bit of water just on the surface of the laminate flooring. We ran an emergency pump out of the window, but the damage was already done. The laminate was cupping by the afternoon and it was so not going to be ok. Water in every single Delta FL pocket, filling up past my thermal break, through the plywood seams. All has been ripped out and is a big insurance job now. The difficulty I face is we laid our great big beautiful subfloor first and then built walls. Now we have to rebuild under those walls. My recommendation, following this experience is to build walls first, then do Delta. I don't know if there is a sacrificial product that can go on the concrete level, but I'd be looking for one and then put the bottom plate of the wall on top of that. Could composite wood material work? Is anyone using this method of construction? What's needed is something impervious to water to give you a couple of inches grace before water hits the wall framing. Then Delta all internal floor spaces and seal, thermal break, 5/8" T&G plywood. Would you save the floor if you used marine ply? If someone hasn't already designed a system for this, I don't know why. 3M, Corning, I'm looking at you awesome ideas generators. PS As a preventive measure, we also installed a second sump line on full strength sump pump, plus a battery backup unit with alarm in case of all round power failure.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
LadyDMcollector thanks for sharing your experience. I framed my walls first before installing the Delta-FL. I used BluWood (mold/mildew/insect resistant) for the bottom plate. I staple FoamSealR Sill Gasket (made by Owens Corning) to the bottom of the base plate. This way the wood is not in direct contact with the concrete slab.
@LetsDoMath
@LetsDoMath 7 жыл бұрын
The BluWood sounds good for the bottom plate. We didn't use that (not aware of its like in Canada), just regular construction grade pine. Can BluWood withstand a flooded basement situation? Insurance companies are whizzbang about ripping out your basement installation, I notice. I absolutely loved the codeboard thermal break between the Delta and the plywood. Can't wait to reinstate that. I think we're going to have to use spray foam under the bottom plate to the wall, since the tear-out crew damaged my codeboard on the wall under the walls. So... next time I design a basement build, I'll be thinking about how I can refit in case there's a flood, AS WELL as installing multiple sump pumps and backups. Sigh. Good for you, putting up a no-nonsense film. Nice job.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
LadyDMcollector thanks I appreciate it. I'm from Toronto you can purchase BluWood from Lowes. It's unfortunate that you had a flood in your basement. Thanks for sharing what happened. I'm sure others reading through the comment section will learn from your story.
@LetsDoMath
@LetsDoMath 7 жыл бұрын
Hope so, that's why I was so detailed.
@digibluh
@digibluh 6 жыл бұрын
at least you noticed, it can pool under the floor and into the pockets without affecting much immediately which is a disadvantage of this type of floor. while mine is well waterproofed, on the lowest/slopped parts i put tiny access panel in the floor i can manually check or put a small alarm under like leak detect rope. leaks will pool there and you'll know before its too late.
@arturfekeshazy
@arturfekeshazy 3 жыл бұрын
Thank You for the regular everyday normal guy installation video! cheers
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
No problem! Thanks for watching and the support.
@noneya135
@noneya135 3 жыл бұрын
Thank you for making this video. One of the easiest overall to follow.
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks for the support! It's much appreciated.
@xavspeedy
@xavspeedy 8 жыл бұрын
Thanks for making this video. I was looking at a solution that would let the concrete slab breathe while being able to add insulation. Do you think I should be ok putting in that order : fabric, dimpled plastic sheet, rigid foam board then vinyl (like laminate snap-on)?
@simpsonpropertiesltd
@simpsonpropertiesltd 8 жыл бұрын
The materials and order you listed them in sounds great. I personally have never used foam board for added insulation. Let me know how it works. Thanks for your feedback and comment. Don't forget to subscribe to my channel to stay connected. Dwight
@ridsouto
@ridsouto 7 жыл бұрын
Great video, thanks! One question: would you lay down some foam underlayment on top of the OSB before installing the laminate? I guess that would make it less rigid, right? You don't lay the laminate in the video, so I'm asking.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Thanks! Yes definitely use a foam underlayment if you're installing laminate flooring. Some laminate floors come with an under pad built-in as well.
@TheItalobarone21
@TheItalobarone21 4 жыл бұрын
Excellent video. Covered everything (no pun intended) and you didn't take forever to do it. Basement looks great!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks!
@juanpulgarinospina9996
@juanpulgarinospina9996 6 жыл бұрын
Great men. Excellent explanations. I understood every step. Thanks a lot. Good luck in every project.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks Juan!
@zakdylanwass
@zakdylanwass 7 жыл бұрын
Hey man, thanks for this video, I'm going with this technique with the added 1" rigid foam insulation on top of the Delta FL. I have a question for you, I've had some moisture issues in my basement and aside from digging around the house and installing a better drain system and gravel, a contractor told me I should also seal all the basement floors with redguard to keep moisture out. That's like an extra $1K and am wondering if that wouldn't only create more problems down the line with the concrete not being able to breathe.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Zak Dylan Wass Zak Dylan Wass thanks Zak! I would recommend that you address any moisture problems and waterproof your foundation prior to installing the subfloor. Excavating around the perimeter of your home, fixing any cracks, installing new weepers and foundation wrap is the best way to address the problem. A cheaper alternative is to do an interior French drain system but addressing the problem from the outside is the best. The only time I have heard of waterproofing products being used on the concrete pad is due to hydrostatic water pressure. Any cracks in the concrete surface were chipped clean and K7 Waterplug was applied. It has a compressive strength of 5,500 psi after 28 days. Then a coat of Terraco Weathercoat 571 was applied. It's a waterproof coating suitable for concrete, masonry and plaster. I believe Redguard is designed for waterproofing wet areas such as a shower. You would have to check the product specs to see if it's rated for reducing hydrostatic water pressure. I don't think it's design for foundation repair. Once again, if possible you want to address any moisture problems from the outside.
@billywilliams3834
@billywilliams3834 2 жыл бұрын
Could you install tile on this?
@billywilliams3834
@billywilliams3834 2 жыл бұрын
I have a three season room I'm looking at putting ceramic tile on I have the Ditr product I'm looking at putting rigid foam over it and tile board over that would this work or would you recommend another route? Appreciate the detail in your video.
@richardhaslam6570
@richardhaslam6570 7 жыл бұрын
I came across this video at the perfect time...I am looking to finish my basement and this method seems to be really economical compared to the Dri-core method, also it seems so much simpler to do. How do I access your other videos...you also have very good presentation skills
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Thanks Richard, I appreciate your feedback! This is a much more economical and efficient method compared to using Dri-Core. Here is a link to my Channel: kzfaq.info/love/O6uBjL3lbJEVQEwmEmPJxw Make sure you subscribe to my channel so you can get notifications when I upload new content.
@albertbranca4644
@albertbranca4644 6 жыл бұрын
Richard Haslam and
@tjmoreth2255
@tjmoreth2255 6 жыл бұрын
cool i dont care
@brianappelbaum8976
@brianappelbaum8976 6 жыл бұрын
Great video, and thanks for being so generous with your honest advice and perspective. Keep up the great work. I am doing a home theater and was not planning to do a subfloor. Just want to carpet the room. I understand the need for a subfloor for the nice laminate floor you did, but is it ok to do carpet and pad directly on the concrete floor? Thx.
@1UTUBEUSERNAME
@1UTUBEUSERNAME 4 жыл бұрын
Yeah, excellent video. Well done. I will use this system on a basement I am doing right now. Great notes in the title section as well.
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
1UTUBEUSERNAME thanks ✌🏽
@_tor
@_tor 7 жыл бұрын
Your videos are very professional and very thorough. One of the best on youtube. Looking forward to more.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Tor thank you so much! That means a lot to me. I have recently invested in new camera & audio gear. I am currently filming a new web series that will be documenting building my families dream home. Those episodes should start airing in the fall.
@_tor
@_tor 7 жыл бұрын
That sounds exciting. I'm really looking forward to this. Having seen many videos, I get the feeling you've got something unique here. Cheers :)
@lefthook25
@lefthook25 5 жыл бұрын
Great video and very informative, but I have one Question: In your tutorial here, you stated that the manufacturer recommends low expansion foam at the edges, but instead you used the tuck tape to seal it down to create the vapour barrier. I was told by the manufacturer that you don't tape down the edges, because that 1/4'' gap is for the moisture to escape. Could you clarify the reason why you taped the edges? Also, they say leave a 1/4" for the DMX from the drywall, do you do the same for the OSB on top? I'm about to do my basement floors and I want to make sure I"m doing the right thing. Thanks.
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks! Just to clarify I used Delta-FL in this tutorial not DMX. I used tuck tape on the perimeter to maintain the vapor barrier. The slab conditions were typical so I’m not concerned about excess moisture beneath the subfloor. The main purpose of this subfloor is to provide separation between your finished floor and the concrete slab. The way I look at it is when you’re installing vapor barrier on a wall you don’t leave the perimeter with no seal so the wall “can breathe”. Ultimately the choice is up to you. This is the Cosella Dorken tech support line I use if you’re interested: 1 (888) 433-5824
@dr.voland8754
@dr.voland8754 8 жыл бұрын
I just removed laminate as there was mold smell coming from foam film that was put directly on concrete. I like Delta-FL idea but not sure about landscape fabric. Can it spread mold grows?
@simpsonpropertiesltd
@simpsonpropertiesltd 8 жыл бұрын
The landscape fabric is designed to be buried in soil and not break down from exposure to the elements. You won't have any issues with the landscape fabric growing mold. You can skip that step and not use it but then there is a chance of hearing that hallow sound.
@diggler306
@diggler306 7 жыл бұрын
Great vid. It really affirmed a lot of the things that I've been thinking about in my head while weighing my basement flooring options. New subscriber here!
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
That's great to hear! I will be uploading more content soon. I appreciate that you hit the sub button. If you ever have any questions let me know.
@carmensita9681
@carmensita9681 6 жыл бұрын
Awesome job man i really liked how it came out. Hopefully it ll be my next project in my basement
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks! Best of luck with your project.
@jordanm7643
@jordanm7643 6 жыл бұрын
Thank you, I almost skipped the fabric step.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
You're welcome! It's an important step in my opinion. I'm glad you watched the video before your install.
@davidmann3536
@davidmann3536 3 жыл бұрын
Not sure why you would emphasize cleaning all the organic material the apply landscape fabric which can contain organic. Once you screw down the subfloor the noise should be eliminated.
@MTB_Bay_Area
@MTB_Bay_Area 4 жыл бұрын
Do I need to level the concrete before I start working? my floor has up and downs about 1/2 inch. Thank you
@vaughnerhardt1510
@vaughnerhardt1510 4 жыл бұрын
Yes you should. Floor leveling compound is easy to mix and pour, it dries fast and saves a lot of grief and disappointment later.
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
This is directly from the manufacturers installation guide: The floor should be as level as possible. Remove any bumps or ridges. In areas with depressions greater than 1⁄4”, self-leveling compound should be used.
@DawgFather09
@DawgFather09 4 жыл бұрын
@@simpsonpropertiesltd What about areas with a 3 inch depression?
@justincarter9622
@justincarter9622 7 жыл бұрын
Great video very informative, I learned something knew today. Thank you for making this.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
No problem Justin! I love hearing comments like this. Make sure to subscribe to my channel to stay connected.
@NoRoads2AllRoads
@NoRoads2AllRoads 5 жыл бұрын
if you use the gun for the foam, it actually controls it pretty well. Does not make a mess at all and the bead is very controlled. I have one and probably would do it that way
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Good to know. Thanks for your input!
@Anthony_The_Disney_Guy
@Anthony_The_Disney_Guy 4 жыл бұрын
Landscape fabric under the Delta FL. Brilliant!
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
Simple ideas are always the best ones 💡
@jamesalexander8368
@jamesalexander8368 6 жыл бұрын
Excellent video and advice....I am currently in the process of finishing a basement floor with the 2'x2' panels...there's a lot of work pounding them together....I will be using your method on my next project
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
Thanks!
@user-xw8tt1uj4o
@user-xw8tt1uj4o 6 жыл бұрын
Very good video. the lady behind the camera sounds that has hypnotized from your perfect job.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
The lady behind the camera is my wife and was probably annoyed to film this. Far from being hypnotized by my work hahaha
@jasonkraus2831
@jasonkraus2831 4 жыл бұрын
Way late to this vid - but this is exactly what I need to do in an old porch turned sunroom on my 80yo house. Quality stuff. Thank you!
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
No problem! Thanks for watching!
@thomaslowry7813
@thomaslowry7813 7 жыл бұрын
Thanks for the great video! We just finished 730 sqft basement and built the entire subfloor the same way your video describes. Our basement is very dry and the sump pump rarely ever runs. Only difference is that we are going to do our framing on top of the subfloor and we taped the Delta FL to our rigid foam installation instead of the walls. We will frame next and add Roxul R14 batts for total of R20 insulation. Took your advice with the little bit of silicone in the holes as well. All 230 Tapcons we used went in easier than expected! I recommend buying the Bosch bits, in a longer length than the ones that come with the Tapcons so its easier to get the depth that you need since you need to go in deeper than the length of the tapcon. One thing, in your description, the 1/4" tapcons require 3/16" bits, not an actual 1/4" bit. Also thanks for the landscape fabric tip. Worked like a charm and only added $50 to the project!
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Thomas Lowry thanks for the feed back I really appreciate it. I will update the bit size in the description. I ended up using an SDS drill as well. It was much faster. I'm currently building my families dream home and documenting the entire build. I will be shooting an updated version of this as installation as well. Good luck with the rest of your project!
@jamesmccarthy939
@jamesmccarthy939 6 жыл бұрын
I'm doing something very similar, but I was going to hold off on rigid foaming the walls until I decide when I want to frame the walls. For now it will just be the floating floor in the basement. Question: can I tape the edges of the plastic right to the concrete walls as my vapor barrier or will the tape not hold well enough? Thank you!
@tch632
@tch632 5 жыл бұрын
@@simpsonpropertiesltd : Agreed! SDS driils are the best! Driils like butter! 👍
@NaeDeen
@NaeDeen 9 ай бұрын
I am super late but I’m beyond grateful for this video. Thank you so much! I’m building out my basement gym & the price of the dricore is killing me. I’m going to purchase the items in the video & I will install it in the rest of the basement to avoid spending my life savings on a floor. Thank you so much!
@simpsonpropertiesltd
@simpsonpropertiesltd 9 ай бұрын
I'm happy to hear you found the video helpful! Wishing you the best of luck on your project.
@markhewitt3160
@markhewitt3160 6 ай бұрын
Use Simpson Strong-Tie Titen Turbo masonry screws. They drive easier and are stronger, which means they don't snap as easily. You'll be glad you did.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 ай бұрын
@@markhewitt3160 Thanks for the heads up!
@davidgipe
@davidgipe 8 жыл бұрын
Great Video! Answered all my questions in one shot. Thank you!
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
Thanks for watching!
@pdoshadow
@pdoshadow 8 жыл бұрын
thanks for posting this video. great info.
@clintonaclarke
@clintonaclarke 5 жыл бұрын
Great work on your video, this was very helpful
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks Clinton! That’s awesome that you found my video helpful.
@furball2585
@furball2585 4 жыл бұрын
Well explained, easy to follow, great advice... even the boo boo's Easy Peasy to follow these instructions.. Thanks... Keep these coming...
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
Thank you 🙌🏽
@whatchinmewatchu7031
@whatchinmewatchu7031 4 жыл бұрын
Landscaping fabric is nice. Roofing felt, tar paper is a better option if your basement floor "sweats, or wicks water" like in an older house where the builder didn't use poly under the slab. The tar paper will hold the moisture underneath better than a regular poly vapor barrier and the water concentration will reach equilibrium and stop wicking.
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
That's a great point for people who have concrete slabs with a heavy moisture content. Thanks for the tip!
@mikew151Manhattan
@mikew151Manhattan 4 жыл бұрын
In the UK we call this product / method "tanking". That's what you should search for if you are interested in doing this over here. Great vid btw!
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
Thanks for the info. That’s interesting!
@UOAPlays
@UOAPlays 4 жыл бұрын
Thank you for giving us some honest information that's not skewed by some sponsored deal. This is how KZfaq used to be. Now it's all just clickbait commercial garbage. Thanks man, I'm gonna check out some of the other "how to" stuff on your channel. I just bought my first house and I'm finishing the basement. Just started pouring concrete after busting up the floor and putting in drain tile, and some of your videos cover things I'm about to start doing.
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks for the feedback and support. It’s much appreciated 👍🏽. Best of luck in your project.
@landy557
@landy557 7 жыл бұрын
Excellent tutorial!
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Thanks Orlando I appreciate it!
@jonathankemper178
@jonathankemper178 8 жыл бұрын
Excellent video. Thanks for the information.
@simpsonpropertiesltd
@simpsonpropertiesltd 8 жыл бұрын
Thanks Jonathan! Make sure to subscribe to my channel I will be posting a lot more videos in the new year.
@jeffpasoff2687
@jeffpasoff2687 5 жыл бұрын
Thank you for sharing your knowledge very helpful. 👍
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
No problem! I’m so happy you found the video helpful.
@angipp01
@angipp01 7 жыл бұрын
Great video. I used the same technique as you. I went with DMX (yes I agree with you, all the same). The only difference technique I used I didn't drilling with screws into concrete. I used Mending plates to join and lock all the OSB floors. Using the Mending plates makes the job easier and less time to drill in screw. (yes drill the screws if there is a bounce in the floor). Therefore, your Delta is floating and so is your OSB floor. thanks for the video. Yes it is cheaper then dry-core.
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Ang ipp thanks for you comments! I'll have to check out those mending plates.
@stevenlunsford2304
@stevenlunsford2304 3 жыл бұрын
Thank you. Smarts with budget saving tips. Good video.
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks 🙏🏽
@Stallion23
@Stallion23 4 жыл бұрын
Great video man! That is a good looking room.
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks!
@57ashdot
@57ashdot 5 жыл бұрын
Really well explained, thank you
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks for the support it’s much appreciated!
@jeffgreen4903
@jeffgreen4903 4 жыл бұрын
Gee, you made it look easy! Thanks!!
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
No problem 👍🏽
@Robnox365
@Robnox365 5 жыл бұрын
Thanks man. These are great videos. Well done.
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Robnox365 no problem! I’m glad I could help.
@bsnrao315
@bsnrao315 3 жыл бұрын
Very nicely done
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks!
@qualityrenov
@qualityrenov 6 жыл бұрын
great video, thank you for posting this.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks!
@hoserbob
@hoserbob 8 жыл бұрын
thanks for the detailed video. much appreciated.
@simpsonpropertiesltd
@simpsonpropertiesltd 8 жыл бұрын
I'm glad you found the video helpful. Thanks for the positive feedback!
@chaccaron4321
@chaccaron4321 3 жыл бұрын
Great video, very informative. Thank you!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks 👍🏽
@jfk128
@jfk128 5 жыл бұрын
Awesome vid!!! I am finishing my office in the garage - this is most helpful!!!
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thank you 🙌🏽
@travischilders1
@travischilders1 4 жыл бұрын
Thanks, that.s what I was looking for . Great job.
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
Thanks!
@clintonaclarke
@clintonaclarke 3 жыл бұрын
Very helpful video!
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
Thanks for watching!
@whatchinmewatchu7031
@whatchinmewatchu7031 7 ай бұрын
This is an excellent technique, differences .. use ZIP flashing tape especially on perimeter. Use tyvek then fabric over the concrete. And 23/32 tongue groove OSB, and glue the joints.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 ай бұрын
I really like those details you use. I’ll give that a try in my next project. Thanks for sharing!
@Psychlist1972
@Psychlist1972 6 жыл бұрын
Nice install and video. Great tips.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks Pete!
@HiiCeenoTheScientist
@HiiCeenoTheScientist 7 жыл бұрын
Great Video can't wait to give it a shot
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Al Welch thanks Al! Have fun with your install 😄
@michaelvizzoca5318
@michaelvizzoca5318 6 жыл бұрын
Great stuff! Many thanks
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
No problem. Thanks for watching!
@markpyles9731
@markpyles9731 4 жыл бұрын
Wow awesome great job
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
Mark Pyles Thanks!
@TheSoundofRainfall
@TheSoundofRainfall 4 жыл бұрын
love this. well done.
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
Thanks!
@gc745li
@gc745li 4 жыл бұрын
Thanks been researching doing the same thing. Great video
@simpsonpropertiesltd
@simpsonpropertiesltd 3 жыл бұрын
No problem. Thanks for watching 👍🏽
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Go Follow Simpson Properties on Instagram for behind the scenes shoots and a preview of upcoming content! instagram.com/simpsonproperties/
@fiveaces1029
@fiveaces1029 5 жыл бұрын
Great idea great video, great tips thank you
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks for the feedback it’s much appreciated!
@Badazz08
@Badazz08 6 жыл бұрын
Nice video and good looking room also. Good job.
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks!
@vanessab.9996
@vanessab.9996 6 жыл бұрын
Question: Thougts on mending plates instead of tapcons? I want to avoid drilling into the concrete, am on a budget, & will be sealing the OSB to use a “finished” floor until I’m ready to lay down plywood planks. I’ve taken copious notes on this video as I am doing a DIY remodel (with zero expertise) on my little house. So far, this video +comments has been the most helpful. I would love to follow your recommendations....EXCEPT, it would incredible for me if I could use mending plates rather than tapcons (both of which I had to look up, since I had no idea what they were!). Last year, I prepped, I sealed & painted the concrete thinking that it would fine, as I am in a warm, dry climate - but, it’s cold in the winter....so, now I’m committed to an insulating sub-floor. I know about dricore, but cost is a factor & it doesn’t look like rocket science...especially if I don’t have to drill. Thoughts & advice much appreciated!
@simpsonpropertiesltd
@simpsonpropertiesltd 6 жыл бұрын
Thanks for your comments and questions! I have never heard of mending plates as well until you mentioned them. I looked them up and I could see them people a possible issue for your finished floor. Now your subfloor surface will not be perfectly smooth due to the mending plates. I would contact the manufacture and ask them if its recommended using the mending plates rather than tapcons. Here is a link to the companies contact page: contact:www.deltams.ca/contact_deltams.htm
@machinegunmessiah8038
@machinegunmessiah8038 4 жыл бұрын
getting ready to do this in my garage, can't wait
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
I hope it worked out well 👍🏽
@shirleyparker2745
@shirleyparker2745 4 жыл бұрын
Very good idea I was going to install those panel at $8 a piece Thank You
@simpsonpropertiesltd
@simpsonpropertiesltd 4 жыл бұрын
No problem. I’m glad you enjoyed the video.
@TRINI123A
@TRINI123A 5 жыл бұрын
Great video. Great detail. The last one wants is to find out after the floor is done is they put the membrane down the wrong way. :-)
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks! Image installing all the uncoupling membrane upside down haha. That would suck.
@owencayton4078
@owencayton4078 4 жыл бұрын
Great video! Thank you very much. I am getting ready to do this in my basement...starting on it next week, I hope. A couple questions: first, are there advantages to laying the flooring and the underlay lengthwise in the room, as opposed to the shorter direction? Finally, would there be any benefit (or drawback) to crossing the seams, i.e. running the underlayment the shorter direction and the osb the longer direction? Thank you for any help!
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
It’s looks better IMO to run length wise. Makes the room look bigger.
@juechi61
@juechi61 5 жыл бұрын
Thanks for all the great videos. I was planning on using xps board for the walls of my basement until a contractor gave me a very reasonable quote for closed cell spray foam. How would you suggest taping or sealing the closed cell foam's uneven surface to the pressure treated board with foam under it and the dmx roll with rigid foam on top of it and still get the vapor seal?
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
You would instal your subfloor first, then walls on top, install spray foam in all the wall cavities. The closed cell foam does an excellent job of sealing between the OSB subfloor and foundation. Creating a continuous vapor barrier on your exterior walls.
@Overcomer1960
@Overcomer1960 5 жыл бұрын
Thank you for posting this great video. You have saved me $$. Your presentation style is excellent. I’m wondering if you have any videos pertaining to installing ceiling in a basement. I want to use drop but I’m concerned about losing precious headroom. I don’t want to go drywall, I want full access to plumbing, electric, etc
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Russ DeVita thanks for the feedback I really appreciate it! Sorry I don’t have any videos on installing dropped ceilings.
@SBdunks3
@SBdunks3 5 жыл бұрын
Almost done with my installation thanks to your instructions! thanks you! What did you do to level the obd? My cement goes downward
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
You could use self-leveling concrete or shims.
@sarcaseptimiu
@sarcaseptimiu 7 жыл бұрын
Very clear and well structured tutorial! I do have a question for you. I have an enclosed patio addition that has tile on concrete. The patio floor level is lower than the house floor and would like to raise it to the same level. Would you recommend installing this subfloor directly on tile?
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Septimiu Sarca thanks! It's always a best practice to remove the old material then install your new flooring. It's going to be tough to properly secure your subfloor with tile underneath. Usually your sub floor is installed on top of wood joist and fastened with wood screws or installed on top of concrete using concrete screws to fasten it to the concrete slab.
@johnp.manhaeve6765
@johnp.manhaeve6765 7 жыл бұрын
Hey, great video. I found it well done and helpful. I was just wondering have exactly did you fasten down to landscaping fabric?
@simpsonpropertiesltd
@simpsonpropertiesltd 7 жыл бұрын
Thanks John! Gravity does all the work for you here lol. You just have to roll the fabric out and overlap it by an approximately an inch.
@Joshwaslen
@Joshwaslen 5 жыл бұрын
great video!
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
Thanks!
@capella8632
@capella8632 2 жыл бұрын
Thanks for the video
@simpsonpropertiesltd
@simpsonpropertiesltd 2 жыл бұрын
No problem! Best of luck on your project.
@msk4893
@msk4893 5 жыл бұрын
Great video. Very helpful. One question about OSB, should I keep a gap between the OSB for expansion/contraction?
@simpsonpropertiesltd
@simpsonpropertiesltd 5 жыл бұрын
It’s a good idea to leave at least an 1/8” gap between the OSB sheets for expansion and contraction. I forgot to mention that point in the video. Some OSB brands such as AdvanTech have that gap built in to their tongue and groove.
Comparing 5 Different Subfloor Systems and What They Cost
12:16
Home RenoVision DIY
Рет қаралды 317 М.
WHAT is this, and WHY do you want it under your floors?
10:48
Matt Risinger
Рет қаралды 6 МЛН
WHAT’S THAT?
00:27
Natan por Aí
Рет қаралды 13 МЛН
Beautiful gymnastics 😍☺️
00:15
Lexa_Merin
Рет қаралды 14 МЛН
39kgのガリガリが踊る絵文字ダンス/39kg boney emoji dance#dance #ダンス #にんげんっていいな
00:16
💀Skeleton Ninja🥷【にんげんっていいなチャンネル】
Рет қаралды 8 МЛН
How to Install a Subfloor Over Concrete VERSION 2.0!
21:58
Ideal Direct Home Improvements & Indoor Gardening
Рет қаралды 171 М.
10 Beginner Mistakes Installing Vinyl Plank Flooring
12:11
Fix This Build That
Рет қаралды 13 МЛН
Basement Sub floor Panels - Are they worth it?
8:14
Research Design Build
Рет қаралды 120 М.
Plasterboard HACK | Every DIY'er Should Know
11:29
On The Trowel
Рет қаралды 511 М.
How to Soundproof Ceilings Between Floors
4:40
ROCKWOOL North America
Рет қаралды 1,8 МЛН
Slab-On-Grade INSULATED Foundation - Part 1
21:45
Matt Risinger
Рет қаралды 264 М.
My Custom Subfloor System (And It’s Cheaper)
12:10
Home RenoVision DIY
Рет қаралды 523 М.
Жду в тг: @kedrovaalyona
0:59
Кедрова Алёна
Рет қаралды 2 МЛН
Первый Холодец Китаянки
0:51
Petya English
Рет қаралды 4,7 МЛН
Nika loves to eat chicken #cat #cats
0:17
Princess Nika cat
Рет қаралды 3,9 МЛН
ОРЕЛ который 20 ЛЕТ летал с GPS трекером 😱 #Shorts
0:28