Great job really helpful. Best video out there

Is the solid purple wire positive and the purple with black wire the ground?

Did you have to trim the fender trim plastic?

please how to find the door wire color for Santa Fe 2020 if you dot have module i mean CAN H and L? thank you

I bought this exact same set slightly used with the pass through OBD plug to leave one port open for 700.00. I didn't have the instructions and your video was spot on!

I have an OBD dashcam. Will two OBD plug and play systems work at the same time (leaving them both plugged in)? Also, how does that light 3M tape hold up to high temps? The temp gets over 100 where i am, can't imagine how hot the road is.

Please furnish deployed measurement from top of step to floor on 2019 GMC DENALI 3500

when spending that kind of money, why wouldn't you use a torque wrench to the recommended specs?

Anyone know what size the bolts are that hold them to body? I lost my mounting bolts after selling truck

Is this is 6 inch suspension lift? TY

Can they be put on a 97 GMC Sierra k1500??

Do i do the same with my 07 Avalanche

What about an OBD2 pass through for, tuners, pedal commanders, etc...?

I have amp steps on my 06 f250 passenger side works perfect. Driver side will not go up. I’ve replaced the motor and the wiring looks fine, any ideas?

What do you do if you have a tuner in that port?

Very nice good job buddy”

Do the rear doors run off the same trigger wires as the front driver and front passenger trigger wires?

I bought some from a Silverado 2015 2500 I just have a question would they fit mine I have a Silverado 2014 1500...

How much dose this kit run for

Is that adhesive durable or will it fall off easily??

What if I already have something plugged into the OBD2 port?

I would be so tempted to do to these what I have done to the ones for my Navigator. That is to remove the pins and set them up for zerk fittings on each end so that you can actually grease the pivot points. All of these steps use a steel bushing with a plastic bearing surface. That surface gets worn and then the boards stick. If I have made you curious, then take a look at my rather extensive set of videos on rebuilding the hinges with pins altered for zerk fittings. It is here: kzfaq.info/sun/PLoz-2IH4A2KsZiDXB0f-hhKZtAzO_wuO_

Do the boards come down when you remote start???

Or…. (hear me out)… You can just play the install fast n loose 12 beers deep and then ur steps will be wired inverse of each other so when u open the driver side the passenger side comes down, would highly recommend it😎

What's the maximum weight capacity for these?

What if you have something plugged into that ODB???

Why do the instructions call for you to go through the body mount if you can just install them the way you did?

Mucho bueno

Spend 1k on steps and have to put the motor on myself? That doesn’t make sense.

should of connected the two purple to the back of ADL outlet and not using the ADL plug.

Very Noice !! 👍🏼

Just looks so weak on how the boards mounts to the bracket 4 small screws holding the weight. Really don't see why they didn't extend a metal plate under the step supporting the weight.

Really don't like that they only have 2 mounts on each side. Doesn't look like they would hold a lot of weight compared to factory that has 4 mounts per side. Just wouldn't want a friend being overweight breaking them. Would buy them if they had the same as the factory step sides.

I dont understand why all these companies don't make these mount to the frame instead of to the body where its half as strong and is prone to rot... i love these steps but I won't buy them until there's a way to mount them to my frame instead I dont like anything mounted to the body that I have to step on with all my weight... there used to be steps that mointed to the frame and then everyone started mounting them to the body ... doesnt make sense...here let's give them a place where dirt and salt etc can build up against the body... love the steps hate the mounting place :)

🤢tywraps🤮

Not worth the 1200 for them and then the headache to install them or the 300 to 500 to have someone do them. Regular steps or hoops are just fine.