Thanks for the video! Watching yours made me want to instal them myself instead of getting a shop to do them. Relatively simple but time consuming, a little bit of trial and error but not too bad. Love them. Thanks for the indirect encouragement!

Great Video Dustin! I'm about to install mine this week, thanks for the video, you did well!

Looks great. Can’t wait to get mine.

Awesome video bro!!! Keep up the great work

I have the electronic steps that were factory installed. It was 1000 dollars for them. But it was already installed on the truck that I purchased. The only thing I have noticed is that sometimes the step doesn’t fold In when I shut the door.

Great instructions my guy..thank you

I’m sold on em. Ordering some for my 17 LTZ.

Great job....Awesome thanks

Does anybody know if these can be adapted to an 83 k20?

Great video! Thanks!

Beautiful 😁👍👍👍

Does the motors go in front Or rear of truck and what side of the truck

Sweet video and truck I got a 2018 gmc sierra 1500 4x4 double cab on June 11th Do do you have any more Factory hacks you can sher with me

Hey Dustin, where did you run the wires from the passenger side to the OBD2 port?

Nice job

Great video brother! Keep up the good work.

How are these still holding up? I just bought the same set for my 2018 Sierra and love them.

I see u said u didn't have to use the u nut because u have pre drilled holes already. Did u drill them yourself or are they on there from the factory? Bout to install tomorrow on my 2016 silverado 1500 and don't really see were id put the u nut for the bracket

After installing steps they dont move when everything is hooked up.nothing happens when I open and close doors when I take motor off I open door motor turns counterclockwise wide when I close door nothing HELP

Where can I buy the obd2 plug and play conector ?

I just ordered these. How have they been holding up have you had any issues with them. Great video by the way !

Can I run these on my truck that has traction bars??

1ST!!!..U AND WALLIE B26 R THE 😎..COOLEST KZfaqRS

Thanks

No fender trimming? Called for in the instructions for the 2015 Silverado and Seirra.

Hey Dustin I hope all is well. I was wondering if the Amp Research running boards have been problem-free and if you would go this route again?

Hi I recently Installed my amp power steps after watching your video and i followed all the instructions but my steps aren't going up at all i can hear the motor power when i open and shut the driver and passenger door but nothing happens any idea what it could be

Hey bro the connection with the purple wires with obd2 connection come with the kit??

What all did you purchase with the kit?

Good video but don't look as strong as the factory step side factory has 4 mounts on each side compared to 2 mounts on each side. Would love if these came with a few more mounts to hold more Weight. Just doesn't look like they would hold a lot of weight. Wouldn't want a friend that is overweight breaking them.

JC... Where’s the GD dramamine???

I can't find the obd2 connection can you share link

Need more lighting my friend

I Work For The Company Its In Tustin,CA

How much do these run?

I bought this set for my brand new 2018 Ram 2500 Mega Cab and they gave me fits to install them! I followed the written instructions exactly to the letter. Got all done, was all proud. Put power to them… And the retracted up under the truck and wedged behind the pinch welds. I worked for hours putting brackets and linkages on than taking them back off numerous times, I adjusted brackets and linkages to NO avail. The boards jammed up and got stuck under the truck every time to the point where I had to remove the motors and pried them out from under my brand new truck scratching up the AMP Research running boards. Decided to call customer service. I called and spoke with Brian Weaver. I explained my situation and he seemed to know exactly what happened. Brian said “they got stuck behind the pinch weld right???” I said Yep!!! He said with a snarky little attitude “I’ll send you an email that’ll explain what to do”… So I get this email with an eight step process to remedy the problem. I followed that set of instructions to the letter again. Well step # 8 said if all else fails take a hammer and bend the pinch weld seam over to make it fit. I tried but I would have had to bend that seam over 45 degrees and I didn’t want to go that far with the sledge hammer. Long story short I had to take a 4” angle grinder, remove ¼” + off the top of the pinch weld seam to get my new $1500 AMP Research’s running boards to operate on my $70,000 brand new truck. Needless to say I was PISSED!!!! For that amount of money the AMP Research product should have fit like a glove. If you are looking to buy a set of nice power retractable running boards LOOK SOMEWHERE ELSE! Don’t spend your money here, You will be Disappointed !!!!! PS… I took the AMP Research badges off the steps so they don’t get any free advertising from me. They better run flawlessly for a long time… If they so much as hiccup I’m going to unbolt them and throw them into the dumpster……. I’ll definitely let you know…….

I don't think you know the difference between nuts and bolts at 10:13 you called a bolt as a nut!!

Audio stinks

If you're going to make a video make a full one no skipping the install on the rear thumbs down