How To Install Cadillac ATS Brembo Brakes On A NewEdge Mustang

No video

How To Install Cadillac ATS Brembo Brakes On A NewEdge Mustang

Рет қаралды 16,931

Күн бұрын

Our Turbo 4.6L 2v Mustang finally got a Brembo brake system upgrade! Not only do these brakes perform extremely well but they look incredible! You can find everything you'll need to do this swap below linked!
S&S Engineering: / ssengineeringllc
Brembo's: www.ebay.com/i...
Brake Rotors: amzn.to/3FP1SVV
Check Us Out ⬇️
MERCH: teespring.com/...
INSTAGRAM: www.instagram....
FACEBOOK: / ratchetwrenches
TIKTOK: vm.tiktok.com/...
What we use to film:
Camera: amzn.to/3kKIaiQ
GoPro: amzn.to/372F9mn
Vlog Case: amzn.to/2OxYyVP
Mic Adapter: amzn.to/2v70e1x
Mic: amzn.to/2udZfNa
Tripod: amzn.to/385Nxmq
Drone: amzn.to/34PJonv
Non Copyright music: www.epidemicso...

Пікірлер: 79

@aaronwilson5508 5 ай бұрын

Its neat to see updated instructions for these platforms. Ive been messjng with these cars for years and this was always one of my favorite mods

@RatchetWrenches 5 ай бұрын

Thanks! Yeah upgrading the brakes on these cars when you start to go faster is a must!

@NewEdgeDesigns 2 жыл бұрын

You always have to use the old bracket with the Taurus brakes no matter the year…Great work guys that is an awesome kit, and truly shows the popularity and expansiveness of the sn95 Mustangs aftermarket parts choices..

@RatchetWrenches 2 жыл бұрын

Thanks! And I didn't know that but kinda makes sense now thanks for the comment. Truly is awesome! So many companies doing awesome things

@RatchetWrenches 2 жыл бұрын

Every photo I've seen on the internet for this, the bleeders are up top. Even saw a photo of the guy who makes the kit comment on a photo saying caliper is on backwards when someone put the bleeder screws on the bottom

@shawnsilverstang2138 2 жыл бұрын

@@RatchetWrenches the bleeder goes on top, you’ll never get them to bleed if it faces down. Think about it, the air has to rise to fully bleed the system.

@NewEdgeDesigns 2 жыл бұрын

@@shawnsilverstang2138 yup you’re correct, the air has to be released out of the top…

@jacobhall1625 Жыл бұрын

I have everything in the garage to do this same setup on my 01. Not sure if you've looked into it anymore since you made this video but lmr sells a cobra rear brake kit that allows you to use cobra rear rotors and caliper brackets with the tauras calipers for even more braking power. Sure the improvement is insane either way though, im excited to see how it performs.

@RatchetWrenches Жыл бұрын

I actually haven't looked into that set up but I definitely will couldn't hurt I'm assuming. Would just have to make sure the breaking bias is equal enough. And yeah this front brembo upgrade really changed the car completely it brakes significantly better and looks 1000% better

@02HeroFitness 2 жыл бұрын

Jesus they look so freaking good! I painted my calipers and got some drilled/slotted rotors looks great but they look so small on an aggressive muscle car! The content is FIRE!!!🔥🔥

@RatchetWrenches 2 жыл бұрын

Thank you! Couldn't agree more they do look so good

@mauricionieto5778 Жыл бұрын

You got a new viewer. I love the content. And for me is gold I’m buying a new edge. Thank you for the videos.

@RatchetWrenches Жыл бұрын

Appreciate that thank you! Feel free to check out our NewEdge Mustang Playlist we put all videos relating to it on there!

@fishsquishguy1833 Жыл бұрын

Really great info and video! I’ve been looking into the 4 piston Brembo Ford Racing front kit for my 03 Mach but this looks to be basically the same thing at a much cheaper price. Thanks for the info! Now I wish somebody from the Mopar world would come up with a similar swap for my 10 Challenger RT that didn’t involve swapping to pricey SRT spindles. Mustangs are so much easier to mod for sure!

@RatchetWrenches Жыл бұрын

Thank you appreciate that! And yea this kit is very affordable compared to some of the other kits on the market for sure. Would highly recommend. And if only! Maybe one day someone will.

@Novagunner Жыл бұрын

Brembos have been available for the new edge as long as i can remember... but its sooo much damn money... 3k-9k depending on the model, as there are a few.

@87turbotbirds 2 жыл бұрын

Yes, Love the stang videos!! Keep em coming!!!

@RatchetWrenches 2 жыл бұрын

Thank you! We sure will 👍🏼

@cloudrehzii 2 ай бұрын

How’s the stopping power with this setup ? Planning to do the exact same . And thank you for the lines and other info you provided much appreciated dude

@RatchetWrenches 2 ай бұрын

Anytime! And it's NOTICEABLY better. You really do feel a big difference IMO. I love the new brakes and they look 10x better too!

@bullet2096 2 ай бұрын

Doing this swap now. Unfortunately 950.61001 brake hoses are the wrong thread size for my GT hard brake lines.

@RatchetWrenches 2 ай бұрын

Good luck with the swap! You're gonna love the upgraded braking ability now. And ahh that's unfortunate!

@bullet2096 2 ай бұрын

@@RatchetWrenches There is a right and left side. Almost finished. Keep making videos your channel is helpful.

@Adam_S281 2 жыл бұрын

Those brake hoses should fit. They are side specific, grab the other hose and it should install no problem

@RatchetWrenches 2 жыл бұрын

Ah damn thanks for the input. I already returned them so maybe I'll buy them again.

@mchristr 3 ай бұрын

Nice. And you need some jaw protectors for your vise so you don't chew up items made of softer metal.

@TPMach1 2 жыл бұрын

Hey man I love the video/content! I’m currently doing this same brake it on my ‘03 Mach1! I just wanted to ask where did y’all get y’all rear calipers from? That’s the last thing I need! Thanks for this! Never knew this was possible!

@RatchetWrenches 2 жыл бұрын

That's awesome! So I bought the rear calipers at Autozone. Its crazy how well the kit works I love them

@TPMach1 2 жыл бұрын

@@RatchetWrenches gotcha! Also with that setup did you have to use that rotors only or could you use a different one? I bought the EBC rotors for my setup like this but I haven’t put them in yet. I’ve just still been doing a lot of research to make sure they fit first. I have a ‘03 Mach1 and they’re made for that car. I just want to be safe than sorry man lol

@RidinDirtyRollinBurnouts Жыл бұрын

I don't think you'll need to do the rears, our Mach 1s come with Cobra brakes already

@ElMachChingon Жыл бұрын

@@RidinDirtyRollinBurnoutsThere’s a vid here on YT that says you’ll need to upgrade the rear calipers if doing the ATS upgrade. Reason being the brake balance will be corrected and brought back to spec with the bigger piston Taurus caliper. If you don’t upgrade the rear calipers, you’ll be more likely to lock the brakes up and crash, IIRC

@steviefresh4602 Ай бұрын

Hell yeah Dude!! This is exactly what I was looking for!! But now im stuck lmao do i buy pads and rotors for the 99 dual piston calipers i have laying around for my 94 Sn95 (believe it or not, the new edge dual piston caliper is an upgrade over the single piston caliper on the earlier model Sn95) to hold me over till i don't mind spending the money on this brembo swap? Or should i just suck it up and start buying parts for the brembo swap out the gate? Lmao either way, my shit needs brakes ASAP!! One of the only thing's along with a couple other parts i have laying around that i want to install before i put her back on the streets😫😫🤣

@RatchetWrenches Ай бұрын

If I was in your shoes I'd just suck it up and start buying parts for the brembo swap! Might as well put all your money towards that off the bat and don't have to go back and do brakes again. It's definitely worth the money

@TheNightmare692009 2 жыл бұрын

If I ever change wheels to one that will clear the calipers I’m doing this.

@RatchetWrenches 2 жыл бұрын

You should! I just drove the car around today and it's a night and day difference.

@tommyhoule9907 Жыл бұрын

Nice setup 👌Can you do a favor for me can you mesurre between front center hub and the end yo caliper i want to know if i can clear my 18 wheel plz before i make a move thx

@cme3172 25 күн бұрын

What brake line did you use the factory lined up? Or did you have to go aftermarket

@RatchetWrenches 21 күн бұрын

I used factory but you can definitely upgrade to an aftermarket SS line if you want

@rickcharles9778 2 ай бұрын

Does anyone know if charger scat pack breaks will fit???

@RatchetWrenches 2 ай бұрын

I am not sure if they will. Possibly a Facebook forum could help you out

@phillipstein9099 6 ай бұрын

You need an adjustable proportioning valve and those pad are crap.

@RatchetWrenches 6 ай бұрын

What pads would you recommend? I haven't had any issues with these

@TheJrt1983 3 ай бұрын

Stupid question but I have a set of 2020 GT 4 piston brake calipers and I was wondering if anyone knew what it would consist of putting them on my 99 GT?

@RatchetWrenches 2 ай бұрын

That's a good question I actually have no idea! I'm sure some FB groups could give you an answer

@cloudrehzii 2 ай бұрын

Just went through this headache . A guy used to make a kit for it to work (went out of business) but the spacers needed to even do it makes your wheels poke . I just sold my s550 calipers to just run the ats brembos they have the kit and the offset isn’t destroyed as much

@DriveWayMafia Ай бұрын

what are your front wheel specs to fit these

@RatchetWrenches Ай бұрын

I have a 17x9 and they clear but literally by millimeters. I was told by the guy who owns S&S Engineering but I'd definitely recommend a different wheel or this in an 18"

@kriskodatt4240 Жыл бұрын

Have you heard about rovos durbans 18 fitting ?

@RatchetWrenches Жыл бұрын

I haven't heard but most 18's should clear its the 17" wheels that have issues

@quarawlisstafford487 Жыл бұрын

Im struggling to find The brake pad pins... anyone have a parts #

@keshawnroberson782 2 жыл бұрын

I love the set-up.. I'm actually starting on my 02 gt mustang 🐎. So question about it.... Everything is stock now but I'm planning on putting all the mods in then stage 3 cam Do you have any guess it will go pass 330 HP??? With me putting that stage 3 cam in?? Because after my next step will be a supercharger or a coyote swap and put the cams in the coyote engine

@RatchetWrenches 2 жыл бұрын

Thank you! And to give you perspective I have a "Stage 2" Comp Cam. Before I went turbo I was FBO and made 289rwhp. 330 might be a stretch but with supporting mods you could get close. If you plan on supercharger or coyote swapping, I wouldn't waste your time with staying NA and putting all the time and money into a stage 3 cam just my opinion. If you went with a supercharger, they make specific cams that work better with them and their powerbands.

@keshawnroberson782 2 жыл бұрын

@@RatchetWrenches thanks for the advice 🤝🏾✊🏾💪🏾💯 And for Coyote swap do Yu perfect f150 coyote engine or mustang coyote engine?? I'm new to this by the way just trying to join the trend 🙂

@doctorsquirts3643 Жыл бұрын

@@keshawnroberson782 you wont hit 330, only way to get close to 330 is cams and heads. With that cam and a set of trick flow twisted wedge heads you might see 330 but thats the only way to get that kinda power NA in a 2V without boost or giggle juice

@mrprfct7069 Жыл бұрын

How did those new calipers feel and compare to stoping power from what you had ? Also it looks like the G2 paint flaked off

@RatchetWrenches Жыл бұрын

It's a night and day difference honestly. And yeah a little bit did due to brake fluid but I touched it up later

@mrprfct7069 Жыл бұрын

@@RatchetWrenches do you happen to know how wide the caliper is ? I am trying to find wheels.

@cme3172 9 ай бұрын

Where do you buy the inserts for the caliber?

@RatchetWrenches 9 ай бұрын

Check the video description for the link. S&S Engineering

@x04svtx Жыл бұрын

Will stock brake lines fit back of brembos

@RatchetWrenches Жыл бұрын

Yeah

@dondo84svo Жыл бұрын

Where did you get the paint from?

@RatchetWrenches Жыл бұрын

Ebay

@ChandlerDeansMachine 2 жыл бұрын

What rotor did you guys end up using on the rear?

@RatchetWrenches 2 жыл бұрын

Whatever one I had on from before. I'll probably upgrade them later this year or whenever they need it

@shelbyGT40 9 ай бұрын

Think these are better than the cobra calipers?

@RatchetWrenches 9 ай бұрын

I don't know too much about the cobra calipers so I can't speak too much about them but I have heard a lot of people run them

@steviefresh4602 Ай бұрын

4 piston brembos are def superior to the OEM cobra upgrade

@umakemerandy3669 2 жыл бұрын

Is this the video of why we havent seen the mustang in a while?

@RatchetWrenches 2 жыл бұрын

One of 2 haha

@umakemerandy3669 2 жыл бұрын

@@RatchetWrenches are we waiting on the other one er did i miss it somewhere lol

@RatchetWrenches 2 жыл бұрын

@@umakemerandy3669 it's being edited currently! Should be up this week

@umakemerandy3669 2 жыл бұрын

@@RatchetWrenches sweet sweet ill be waitin! Got my turbo kit in but still not tuned. Ordered a terminator x in february but it keeps getting delayed! So its nice to be able to watch your similar build in the meantime lol. I wanna see some full rev range pulls from beginning of 2nd to end of 4th :)

@bullet2096 2 жыл бұрын

What rims are those 17s?

@RatchetWrenches 2 жыл бұрын

Yep. These barely and I mean barely clear due to the contour of the inner wheel. I would recommend going 18's or different wheel with the brembo set up.

@RidinDirtyRollinBurnouts Жыл бұрын

@@RatchetWrenches did you have to shave anything to fit with the 17s? Strongly considering these over the Cobra R brake kit as the R came with 18s and can't get an answer on if they fit 17s ot not.