HOW-TO Install LED Lights On Your Snowblower Without The Flicker!
Рет қаралды 223,241
Күн бұрынHOW-TO Install LED Lights On Your Snowblower Without The Flicker!
Help me make videos!
/ donyboy73
Forum article on installation;
www.snowblowerforum.com/forum/...
Lights in video were provided by AUXBEAM
Light used on ARIENS snowblower;
www.amazon.ca/Auxbeam-7200lm-...
Light used on TORO snowblower;
www.amazon.ca/Auxbeam-degree-...
See AUXBEAM'S line up of lights on AMAZON
www.amazon.com/s/ref=sr_as_oo...
AMAZON CANADA
www.amazon.ca/s/ref=nb_sb_nos...
Buy bridge rectifier here;
www.amazon.com/s/ref=nb_sb_no...
Buy capacitors here;
www.amazon.com/s/ref=nb_sb_ss...
Follow me on Facebook; / donybo. .
Twitter;
/ donyboy73
Instagram: / donyboy73
Due to factors beyond the control of DONYBOY73 “The Small Engine Doctor”, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. DONYBOY73 “The Small Engine Doctor” assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. DONYBOY73 “The Small Engine Doctor” recommends safe practices when working with power tools, hand tools, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of DONYBOY73 “The Small Engine Doctor”, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not DONYBOY73 “The Small Engine Doctor”.
#donyboy73 #smallenginerepair
@jepsdog3859 4 жыл бұрын
With your help I installed a 20” oxbeam led light on my ariens snow blower last year and it’s working great, I mounted it on the top of the intake to get better illumination, I have a tarp cab that was in the way, thanks doneyboy you saved the day again that was the prescription I needed.
@jtdundee 5 жыл бұрын
I did the hack - and it works great! I used the parts in the links, mounted them in a gray 4" Carlon plastic electrical box. Used those 4 spade connectors on the bridge rectifier and then soldered the wiring to the capacitors then used a LOT of hot melt glue to insulate the wires (it is non-conductive) and secure the parts in place in the box. On my Ariens 926LE I mounted the box on the bottom of the "dash" out of the way. For power, I just snipped the existing power supply wires to the lights and extended them into the box. For the light, I used an 8", 12 bulb LED light from Harbor Freight (Under $40 with the coupon) and mounted it near the top of the front of the auger housing. I had already mounted an hour meter; that remains hooked up to the original AC output wiring. No switch needed, the light turns on with the engine and there is no flickering when it is running at normal speed. Seems like about 25 times more light than the weak one that came with the blower, with the same wattage. Darn thing lights up my whole block. Thanks for your video!!!!!!!!!!!
@carlmiller1034 6 жыл бұрын
Excellent how-to video with adding lights to a snowblower! Those LEDs definitely look robust and well made. Thanks so much Don!
@marathoner43 10 ай бұрын
I decided to do this on the two snowblowers I have that have stators. I opted to leave out the capacitors and the toggle switch and decided to include an inline fuse. Your video made the process so simple. And I love the Auxbeam lights you recommended. Thanks Don!
@barrybebenek8691 6 жыл бұрын
Once again, a fantastic instructional vid from Don. You make this so easy! Thanks for this light idea. :)
@The1980toyota 3 жыл бұрын
Your last explanation was so much clearer than previous attempts. Thanks for this tutorial, demonstration and parts links!!!
@SteveStubbert 3 жыл бұрын
I followed your video and my LED light works great! I found one with the same 18 watt consumption as the original bulb to protect the stator from being over worked and disconnected original bulb. The lumens are 1100 now as opposed to 263 with original bulb. Thanks! Great video as always!
@Patrick4959 6 жыл бұрын
Bloody brilliant stuff there Donny i can already see this Leaf Blower too so you never miss a thing cheers from Australia to Canada ;)
@ronaldhildreth383 4 ай бұрын
Thanks for the video. I set mine up exactly as shown and the lights are very bright and no flicker. I cut and used the enclosed wire harness and fuse. Great instructions. Easy to follow. Thank-you Don.
@doublewide6 6 жыл бұрын
I like the auxbeam lights I put them on my zero turn and on the back of my pickup for plowing snow. Nice video hooking the lights to a snowblower is tricky wiring compared to a DC 12 battery application. Nice Job!
@donyboy73 6 жыл бұрын
thanks
@charger19691 6 жыл бұрын
I am a huge fan on LED lighting, nice job Don!
@99carnot 6 жыл бұрын
Nice installation,, and good information. Thanks for posting and have a good weekend!
@donyboy73 6 жыл бұрын
thanks steve
@CHIBA280CRV 6 жыл бұрын
Fantastic Donny , thanks for the very informative video.
@mikedickson2925 6 жыл бұрын
LED lights are terrific!!! They sure made a difference with lighting your work area!!! Nice tips too on how to connect so as not to harm the LED's or the blower stator.
@jeremiahmnjohnson 2 жыл бұрын
Love your videos. Lots of great ideas and Your skills are very high in mechanical / Electrical
@aktrapper6126 5 жыл бұрын
Great information and very well presented. Thanks for all the research.
@chuckuu9294 3 жыл бұрын
Dony great video. Awesome explanation simple and start forward. Thanks brother
@luedekermeyer-castens4122 3 жыл бұрын
Enjoy your videos. Good explaining in details.
@johnropeleski6006 6 жыл бұрын
can`t beat led`s. super bright.nice video
@ALAl-zw8tq 8 ай бұрын
It’s working fine on my snowblower thank you for your video 🎉🎉🎉🎉🎉
@robrobi5876 6 жыл бұрын
Tres bien expliquer... sont bien montée tes vidéos...Merci DonyBoy
@richyrich1723 5 жыл бұрын
You Da Man. This light works great. I installed without the capacitors. I couldn't wait until they were shipped. I will install when they arrive. Thanks you. Keep up the good videos.
@richyrich1723 5 жыл бұрын
Re did with the capacitor. WOW. Not its bad ass. thanks again.
@Lilripper850 4 жыл бұрын
What do you need the capacitors for?
@AWoodworkersLife 4 жыл бұрын
tjc1ny I believe the capacitors take the pulse output of the rectifier and helps provide a more constant input to the led. These means no more flickering leds.
@dondupuis7798 6 жыл бұрын
That's great information. It helps a lot.
@Earthy0 6 жыл бұрын
I love your videos as I always learn something new.... I often wondered what that little white connector coming off my snowblower's Tecumseh engine was for.
@arciefan 6 жыл бұрын
I love those lights. No snowblower for me in the south, but I have two of the next bigger size mounted on the front of my boat, and two the size you have shown on the back of the boat. Running boat trails with the reflective posts marking the trails is now easier, and backing the boat up after dark is much easier to see as the two on the back of the boat now act as magnum back up lights. Like them so well and the cost is minimal, I'm considering adding two more on the rear bumper of my truck for additional back up lighting with or without the boat trailer behind. Also for seeing the bank while night time fishing, I have one of the smaller leds on a clamp on mount, that I can dim down with a pulse modulation switch , which is fairly inexpensive also.
@danstankiewicz8222 5 жыл бұрын
I appreciate the information on light installation!!! This would have been really helpful. I found a few lights with magnets located on their base, and set them on my (Ariens) snow blower's metal dash. I didn't have the patience for this modification, at the time. Thanks again.
@aleblanc3547 6 жыл бұрын
It looks like Aux Beam has a good opportunity to make and sell a premade adapter for an application like this one. Thanks, Dony! Nice comment from Russell Booth, too. It looks like he knows his stuff.
@dankotos61 5 ай бұрын
Wow that was a good video. I'm definitely going to do my I want to check those lights for my truck two
@adamflight1 4 жыл бұрын
Amazing video. SUBSCRIBED!
@andywisniewski4344 3 жыл бұрын
Amazing love your channel
@livingwaters7841 5 жыл бұрын
love this guy, awesome
@benmoule8705 6 жыл бұрын
Good job Don I wish we had snowblowers here in Australia soooo hot
@hermanchow1405 6 жыл бұрын
Ben Moule ha ha you have a wild fire to take care of the snow( grass n trees ) for you !!
@rau1367nt 6 жыл бұрын
Thanks for this information, I will use the links for the lights! Only wish my blower had an alternator on it, but a 12 ah battery is a good substitute. I can charge the battery off my garage door opener when not in use.
@rmojo23 6 жыл бұрын
Thanks for this!
@philfalz01 6 жыл бұрын
thanks for the video with your help i wired my toro snowblower thay work great im in buffalo n.y,
@smokenjoe001 9 ай бұрын
THANK YOU THANK YOU THANK YOU! THIS IS EXACTLY WHAT I NEEDED!
@waynebrown5428 6 жыл бұрын
Good info! Thanks.
@gordbaker896 4 жыл бұрын
Power Chute Hack. I utilized an old 12 volt DC reversible drill and a double pole double throw switch with spring loaded neutral centre. Cut off the chute crank handle and chucked it into the drill and securely mounted the Drill to one of the control arms. Mounted my Garden Tractor battery on the Snowblower above the engine in small battery box and now at the touch of a switch I can turn my chute up to 190°. Battery stays charged all season. I have a canopy (highly recommended) and also run a mag base rotating blue light and rear LED red light on top. Because I could. I could easily run additional 12VDC lighting.
@jasonjohst48 4 жыл бұрын
Thinking about upgrading to an LED on my 10.5hp snowblower for either the end of this season (upstate NY)/the start of next season - very informative so thank you. Just out of curiousity do you think an HID headlight with a ballast/relay "could" be installed if someone were to come up with a mount or holder that fits the bulb (maybe in the OEM housing if gutted - or a waterproof enclosure). I've installed HID's on a few of my cars over the years and its pretty easy, this seems very similar without the ballasts - Is there any reason in particular LED is preferred over HID on a snowblower?
@famchez1 4 жыл бұрын
works!! thanks
@craigtimmons3468 6 жыл бұрын
For units without charging systems or electric start one could retro fit their unit with just a 12 volt battery of appropriate size for their equipment or even one from a motorcycle and just attach a battery tender to the battery so when not being used it could be plugged in to keep the battery at full charge. LED's draw very little power so a battery of proper size for your equipment would last many times longer than a rechargeable cordless tool battery and you would just install them as per the manufacturers instructions making your positive and negative connections to the battery. Not trying to beat you down DONYBOY73 but just saying there's more than one way to Skin that Cat. You have great informational and detailed videos thanks for your time.
@Flash1857 6 жыл бұрын
Craig Timmons did that on my tractor for a winch and Strobe light, works very well
@erikc3936 3 жыл бұрын
Great video! Could you use 40amp bridge rectifier in place of the 50amp? I have a 40amp 1000v bridge rectifier on hand. Thanks for your time and help.
@MrTarkus007 3 жыл бұрын
dony your 1 of the few who really posted a great video all the rest of the idiots talk about their beautiful snow blower you would think they were talking about their wives love your video's very thorough !
@bubbsy2002 6 жыл бұрын
I bought a led light that is ac/dc just spliced in same wattage, way more light. Keep up the good work though.
@chrispernette8752 7 ай бұрын
Hello I am adding two of the small aux beams like yours on my snowblower. Do I need to use 2 rectifiers or can I go with one and then tie the two lights in after the capacitors?
@pete70091 2 жыл бұрын
Excellent tutorial. The only thing I would do differently would be to put the switch between the AC wire from the engine and the rectifier. That way rectifier and capacitors aren't energized with no load when the light is off. Great video.
@demetriosa7646 6 ай бұрын
Perfect that’s exactly what I ended up doing. And u can only use a basic 2 prong switch not a lighted switch bc it won’t make the stock light as bright as it normally would !
@sylvainarseneault2501 3 жыл бұрын
Good job Body 👍
@TheShawna1 6 жыл бұрын
The wires coming from the blower are carrying AC voltage.The rectifier changes it to DC like your car. The capacitors filter the current ie: take out the pulsating that would be apparent with out them shrink wrap all of that well.wish my older ARIENS 521 had the magneto on the engine for lights.jim
@nickl1682 6 жыл бұрын
Nice job .
@danielrobert7181 3 жыл бұрын
Good video Donny, it doesn't matter which AC connector you elect as your positive or negative because that current "alternates" between + and -. So each terminal is alternatively positive and negative.
@donyboy73 3 жыл бұрын
thank you!
@lbettio5637 2 жыл бұрын
Hi Don, you are providing great videos. Thanks. Ok this question may have been asked but am curious to know if u can get hand warmers installed on my 2007 Toro Max 826 LE? Also wanted to know how the steering assist on some newer snow blowers differs to the non steering assist ones, mechanically? In other words how does steering assist work? Is there any steering mods one can do to say the Toro 826 LE? Probably no or too expensive, I just was wondering. Loris
@redskool8498 6 жыл бұрын
kool don you seeing the light haha .... have a good weekend .. †
@WhatIThinkNation 2 жыл бұрын
Does the rectifier heat up at all ?? im debating to make a nice 3D printed enclosure for the rectifier and the capacitors so its a nicely sealed up unit for my honda. The larger honda boys have an onboard 12v battery so its a much easier upgrade :) My little unit only has a direct power line.
@robrobi5876 6 жыл бұрын
Merci Donyboy73 ... j'ai fait mon montage de mes fils exactement comme tu la expliquée pour les lumières de souffleuse Capacitors + 50 Amp 1000 Volt KBPC5010 et c'est fou comme ca fonctionne bien merci. j'ai acheter mes lumières 4 pouces sur Ebay d'un vendeur en ontario voila son nom... ailight...vraiment pas cher...et tu devrait faire en francais l'ajustement de carburateur et le bras du engine speed ca serait bien... la j'ai un peu de misère a suivre. mais tes vidéos son toujours bien montée avec tout les détails. Bonne journée Ps: J'ai une veille souffleuse Columbia 10-28 1986
@misterfakeid 3 жыл бұрын
So I can put a higher wattage light bar than the 18w that I've seen on other videos?
@amichke 4 жыл бұрын
AWESOME instructions! I successfully followed the directions and installed a set of LED flood lamps on Troy-Bilt 28 dual-stage snowblower (that has heated grips). The only additional modifications that I made were to use heat-shrink tubing to help isolate/insulate the wire/connections points for the rectifier and splices to the power out from the engine.
@NR1853 2 жыл бұрын
Can I leave power to the lights which came with the snowblower and add the bar light to the front of the blower using your method?
@johncalhoun637 3 жыл бұрын
You’ve been a big help making my old junker run better. Looking at your capacitors, looks like electrolytic. Have you had trouble with them in the cold? I might try some thin film or ceramic caps instead? Also looks like your just running both caps in parallel, across the output of the rectifier, but a little hard to tell for sure? Thanks! Btw, I just swapped the 12hp off my old yard king with a junk final drive onto a slightly newer snow king that had an anemic 10hp but a much better final drive design. It’s now a beast that needs a better light.
@DJW1985 3 жыл бұрын
If you have a DC Alternator can you hook the leds directly to the dc side. I have a 3/5 amp AC/DC alternator. I want to add an led light to an 80's Ariens blower, no other electronics. Can I hook right into that 3 amp DC side without a rectifier/etc?
@rogermalonson7613 3 жыл бұрын
I have a Ariens pro 28 926065 and I want to add 2 18watt led no lights. Have rectifier is that all I need?.
@ALAl-zw8tq 8 ай бұрын
I’m not sure on to connect the capacitor ? is there one on each wire going to the light ? Or they are connected together ?
@turboprop50 3 жыл бұрын
Hi Donyboy73. Can this light kit be installed in the Ariens Hydro EFI engine model? Thank you.
@MustangsTrainsMowers 4 жыл бұрын
I installed a new 7hp Tecumseh Snow King engine on my late 80’s JD 524 snowblower almost 10 years ago. It has 110 volt electric start. Can I power a light from the engine? If not I was wondering if I could change pulleys on the engine PTO and install a GM one wire alternator to power lights?
@Fixitmike508 2 жыл бұрын
I love your videos....thank you for sharing your knowledge on KZfaq! Why do you need two capacitors in the circuit? Does it have to do with the amount of LED's you installed?
@joev3315 6 жыл бұрын
like the idea, but with all the vibration will they loosen and come apart . great job , good info. have a great weekend
@daniellele9634 3 жыл бұрын
I see that auxbeam offers bigger ledbars... is there a limit on how high i can go on the wattage with this setup?
@JoeN938 7 ай бұрын
I know this video are quite old but Donny did a great job explaining and I really appreciate you get out the community. @Donny, I have a Toro 1038 Tecumseh and a Toro 1128 Briggs and Stratton. If I follow your method using two pods of 18W, would both engine produce enough voltage to power 36W total?? Can anyone help me answer this question please? Thanks in advance.
@the.artist.donaldb Жыл бұрын
Great video, but one question, where does one get the male connector with cord for the stator female connector wire coming from the engine?
@rh5549 Жыл бұрын
Does it matter on the Uf rating on the capacitor? I have some but they arent 2200
@jimvanderlinden7249 3 жыл бұрын
What is the voltage coming out of the snow blower? Are you increasing the voltage for the LED?
@cwsrad 5 жыл бұрын
Do the lenses yellow after 1-2 years of use or outdoor exposure?
@kingtut5923 4 жыл бұрын
Don this will work for me, how many lights can I install? Also can you get 12 volt charge to charge a battery? I want to install on garden tractor need 12 volt starter. Thanks Ben
@garyduran1 5 жыл бұрын
Thank you..
@hakanjansson1082 3 жыл бұрын
Just bought a ST1032 and wonder how much power the alternator provides ? I bought a 27W LED , would that work ?
@Ricky-eo5ym 5 ай бұрын
How many watts was the light you installed and does it matter ? Thanks in advance.
@gregsgarage6387 3 жыл бұрын
I have a 2019 husqvarna 42” riding mower, it came with normal 1156 bulbs. I piggy backed the oem light wiring to power the twin 6-led bars, did I need to add the rectifier and capacitors? What will happen?
@merqury5 4 жыл бұрын
Does anyone know what kind of volatge and current one can get from the flywheel stator of a tecumseh 8-10hp? Those lamps can quickly be 20-30 w, I dont know if the engine can provide this.
@smokenjoe001 9 ай бұрын
Could you run both of those smaller lights with the lower amperage stator wire?
@Colossus854 6 жыл бұрын
thanx i will try that
@ALAl-zw8tq Жыл бұрын
Do they make 12 volts LED lights ready to be install without rectifier and capacitor ?
@Thibault_95 7 ай бұрын
my blower has a 18 watt alternator what size lights can i use ? i think i have 2 18 watt cube led laying around would that be to much for the system ?
@zx8401ztv 6 жыл бұрын
That made a hell of a difference, like night and day :-D. It makes no difference the polarity of the input to the rectifier, its a bridge of 4 diodes that channel the ac phases to the + output and - output. Even applying d.c to the inputs will be corrected to the outputs :-) The capacitors smooth out the gaps between pulsed peaks, so its smooooooth lol :-D
@brasha78 2 жыл бұрын
Oh Danny boy, you have a surplus of information though I am not looking to put a light like this on my unit, and I don’t already have a light on my snowblower. I just wanted to throw a comment out there for a super video though it doesn’t hit right where I need to be, you are right on time. Additionally, the pipes the pipes are calling Many thanks laddy Also shame on me I did not watch this video from beginning to end so it may have solved my problem though I suspect that it wouldn’t have, by my leave Patrick Begora. (Pardon the Disney reference)
@o0Avalon0o 4 жыл бұрын
I might need to buy some tools & do this myself. I currently use my old clip on LED light from firefighting, BUT it accidentally fell off once; I don't want to be stuck in the dark like that again.
@davidsproat8986 5 жыл бұрын
Wired according to video. My blower puts out 13.4 volts led lights 36 watts 3watts each X 12 installed and grounded out to the blower chasis and starts well. When i switch on the light it lights up and than stallls out the motor??
@tigger1998ca 6 ай бұрын
Great video, going to install one soon. Just wondering what gauge wire you would use
@donyboy73 6 ай бұрын
I think i used 14g
@pj2418 4 жыл бұрын
Donyboy: I love your videos and have learned a great deal. My puzzle is a bit different: I have the identical 18 watt led (fog light) as yours which POPPED the moment I powered it up. So I clearly need to clean up my system for the reasons your are suggesting, maybe... In my case I have a new 13 HP 420CC predator motor that has a starter and a modest charging circuit consisting of just one coil on the flywheel. I am adding a a small 10AH lead acid battery for starting but would also like to run my 18 watt light (just 1 light) and possible my original Toro hand-warmers, even though this may drain my battery as the single charging coil may not keep up with the power drain. Of course I might have to run one or the other and may install a DPDT switch for this purpose. Please tell me this; can I install just a simple voltage regulator to control and convert the voltage coming from the motor to safely run my lights & grip warmers while also charging my battery our would I still need capacitors even with the 12 volt lead acid battery now in the mix? Thanks again for all of the great videos you have created to help out the rest of us!
@richchristman1598 3 жыл бұрын
I used a KBPC 2504 thinking any rectifier would work, but am only getting about 8v dc output... but do have between 12-13v ac input. is this rectifier different than the one you are using (which I just ordered by the way).
@baronftball 3 жыл бұрын
Hey, need some advice I have an old snapper 824 series 1 snowblower. I got an LED light which I mounted to the snowblower and ran the wires to a fuse and bridge rectifier. The LED light comes on for about 15-20 seconds then shuts off. Did some checking with the voltmeter and from the motor 22 volt Ac at 349 hertz? And on the dc side, it's 22 volts. Do you know if the bridge rectifier is overloaded? The fuse didn't blow and the light still works when hooked up to a 20v drill battery. Help please.
@chrisoutdoors8998 6 жыл бұрын
Cool! Can you show how to put these lights on your enduro. My KTM 530 EXC could use more light. Thanks.
@BIGGBULLxxx 3 жыл бұрын
Hi how much will you charge to do my troy Arctic storm 34" 2 stage snow blower.
@billk5727 6 жыл бұрын
Great video Don. I see a lot of comments about overloading the alternator. These snow thrower alternators are just like the lawn tractor ones and when someone runs the battery down trying to start their lawn tractor the alternator is working as hard as it can to bring the battery back up. Even if the tractor has a voltage regulator that regulator only limits voltage, not current. I have only seen these alternators damaged when somebody jump starts the tractor with the jumper cables on backwards and pops the little diode in the wiring harness. Bill
@geojor 6 жыл бұрын
thank you ...
@mikelangieri6602 3 жыл бұрын
This is an awesome video. I've got an older MTD Yard Machine 8/24 with electric start that has one (1) wire coming out with a bullet connector. I don't know how much voltage or wattage that one wire provides, so if anyone can help me out on that I would definitely like to build a light setup. I was hoping to put two (2) small lights on the blower... one on the left-hand side of the bucket to focus on the rear immediately in front of the bucket/auger, the other mounted up high on the "dashboard" off to the right and focused out to a greater distance. So if I used two 18W lights, would that work or is there more powerful lights that could be rigged with Donny's wiring idea?
@FreedomRock44 5 жыл бұрын
Also end of video at 9:59 it looks as though after you tidied up the wires you added a Fat yellow wire and a fat Red Wire which were not seen at previous mentioned times of 4:34 and 9:12 of this video. I am not being a pest I just noticed it and am not very savvy when it comes to wiring. Also Don you mentioned a toggle switch......Any Volt or amps on a toggle switch or ???? When I look up toggle switches they seem to be all different volts and amps 12v/20A.....12v/30A.....then wattage???? Appreciate your help.
@leafer655 6 жыл бұрын
Great vid as usual Don. On snowblower with a 12 v onboard battery can the light be wired direct to the battery without rectifiers or capacitors?
@donyboy73 6 жыл бұрын
yes
@leafer655 6 жыл бұрын
Thanks!
@marshallguerra7429 Жыл бұрын
Nice video. But I have two older Arien’s snowtrowers for the 70’s with no lites on them. How would I do this ???
@suburban91 5 жыл бұрын
Hi. Will these components become hot ? Maybe put them inside a small waterproof box ? Thanks, Bard
@eagle5720 4 жыл бұрын
I have a troy bilt storm 2410 snowblower but it doesn't come with a stator so I'm buying a flywheel with the magnet on ebay and a stator so I hope they all fit
@FrostyTheBeerMan 6 жыл бұрын
Hi Don ! Do you have any video available that shows how to oil a shaft that has a grease nipple on a snowblower ? I have an Ariens brand snowblower and need some help. Thanks if you can post a link if you have done this sort of tutorial. ! Thanks for all your great videos, the best channel out there !
@donyboy73 6 жыл бұрын
if there is a grease nipple then use a grease gun to grease it
Двое играют | Наташа и Вова
Рет қаралды 6 МЛН