Follow the link in description. You will find more interesting things.

In my case, is canbus enabled by navigation. In your case, you will probably connect to reverse lights.

I had a similar problem when the car was off the camera worked fine, but when i turned the car on no signal, then i connected the red and black wires to the wiper motor and now works fine.

I do not know how to call it, but it looks like fishing wire and is used by electricians for pulling wires throw the walls. I bought it from a bricolage store. Try at electrical store. Read my webpage, link in video. Maybe it helps.

I looked it up with the info you gave me and apparently it’s called electricians tape or a wire noodler! Weird!

you prob solved it but, no problem if u damage them but it would be a good idea to change it with new ones later one

For night, camera switch itself to black and white. Rear lights are enought. Don't need IR leds.

@@nichiforiuc Thanks for you answer :)

Yes

I believe is shorter.

Red wire is for power the camera. If you connected to navi, the other side of the wire need to be isolated. If you do not have navi, you can power the camera to the rear reverse light. So, in your case, you power the camera from the navi, you do not need to power it from the reverse light. Isolate the other side.

I use this rear camera with chinese navigation. The red wire is "+". The ground is on the video cable. The video cable is made of two wires: one is inside, for video signal, and the other one is around the first one and is for ground. My english is poor and is very hard for me to explain. Both red wires are for "+" and you can use one. No need to connect both. In my video, the ground is from RCA connector from navi.

@@nichiforiuc Did you need programming before installing the camera on the Chinese radio? Or just need it on the original radio

Hi, you have no Signal/ bad picture or we see that so on your radio?

I choose a wide camera, no setting needed. Plug and play.

170 degree lens

In weekend fac si review pt navigatie.

@@nichiforiuc Abia astept!

I didn't connect that wire to re erse lamp. I connected it to navigation.

Search for rearview camera on ebay. There are many cameras.

Nu stiu. Nu am incercat. Sigur o sa iti trebuiasca codare vcds.

Thx. Follow the link in description for more infos.

Red wire minute 17:40.

The head unit takes the reverse signal from Can-Bus.

@@nichiforiuc so the cam switch on using the wire for reverse triggering , it means no others wire need to be connected to 12v line, that is correct ?

Yes. No other wire. As in the video.

Maybe a stupid question but the long white cable you use i see it not in the beginning do it came with the package or why you choose for that wire thanks im waiting my system to arive this week

Under the carpet, use a hard wire.

In cazul meu, cablul video are cate un fir roșu la fiecare capăt. Cele doua fire rosii sunt pentru alimentarea camerei, și se folosește doar unul din ele. În cazul meu, am navigatie, și din navigație îmi ieșea un fir dedicat pentru a lega de firul rosu si astfel sa alimentez camera. Daca nu ai navigatie, poti alimenta prin firul rosu de la capatul dinspre camera, și ar trebui legat la becul de marsarier.

Vezi si pe site-ul meu, poate te ajuta vreo informație de acolo. Estre trecut și în video, și în bio.

I did not connect the red and black wires. I have navigation head unit, so I do not need the red and black wires. Navigation is powering the rear camera.

There are 2 red cables. One red cable on each end of the harness. If you have android navigation, you connect the red cable to navi, but if you don't have navi, you connect the other red cable from the trunk lid to rear white light. The red cable is powering the camera when you drive back.

Salut. Nu stiu. Scoate navigatia si vezi pe eticheta daca are vreo mufa pentru camera. Ar trebui sa aiba pentru ca navigatia a fost montata si pe modele de audi cu camera pe spate.

ovviamente tutto lo stereo