HOW TO INSTALL THE OIL PUMP IN YOUR CHEVY 350 ENGINE!

Рет қаралды 7,498

Күн бұрын

Installing the oil pump and rebuilding this 50 year old Chevy 350 (CSB) engine block at HOME! No machine shop needed! Installing oil pump pickup.
Check out all my other links:
linktr.ee/garagegoblin

Пікірлер: 23

@robertwilson4400 4 ай бұрын

Finally, down to earth, straight to the point homemade garage with real talk! Thank you for this video you answered two days of searching KZfaq in 7:39 now I can do what needs to be done on my old GMT400 and be back on the road. Thanks again.

@pasqualedemaio919 21 күн бұрын

You made that sound so easy. I just wanna buy a 350 rip the oil pump out and put it back in thanks bud.

@TheGarageGoblin 21 күн бұрын

It is easy! Cars are just adult legos 😎

@Jeremiah.1 Жыл бұрын

Excellent video very well explained

@lukeskypwner278 Жыл бұрын

I don't even need to do this right now. You made this interesting to watch!

@TheGarageGoblin Жыл бұрын

Thank you! I’m glad you enjoyed it!

@chiliwhit747 Жыл бұрын

I would open my oil pump up 1st pack it will grease or valo. to make sure of prime. Very important....💯

@Texasmule Жыл бұрын

Omg thank you bro. I just took off the pan and now I need to take off the pump and replace it with a brand new one

@TheGarageGoblin Жыл бұрын

Glad I could help!

@Texasmule Жыл бұрын

@@TheGarageGoblin would you know how many ft/lb. Of TQ the bolt needs?

@TheGarageGoblin Жыл бұрын

@@Texasmule 60-70 Ft pound. I put 65 on here!

@Texasmule Жыл бұрын

@@TheGarageGoblin thanks! Do you think I should change the old bolts for ARP On my connecting rods? I wanted to do main bolts too but my knowledge isn't that huge so I just left them alone.

@Schlipperschlopper Жыл бұрын

Never use a Melling 55 (today made in China) oil pump! They break in parts, get a Moroso or Summit high flow pump! Better use a soft thin flat copper shim gasket between oil pump and main cap! You cant weld cast to steel....you need a clamp for securing the oil pump pickup to the body...can find it at Summit.

@Tricolor610 Жыл бұрын

Melling not so good …? I have a Stock ( New ) inside …. i have low oil pressure when the engine is hot …. Engine ( 383 is build 2015 ) … from first day … low oil pressure… hmmmmm, Greeting from Germany

@robertlee6936 Жыл бұрын

Is there no o ring anywhere for the oil pump Bc I just did this about a month ago and I’m getting low pressure again but it goes up and down a lot and up when I slow down? I don’t remember seeing a o ring when I did it myself

@Ceo8203 Жыл бұрын

Yes I'm sadistic 😂😂😂😂

@Tricolor610 Жыл бұрын

Hehehe…, looks like easy …. when the engine is outside but my 383 engine is still in my IROC…😵‍💫., I can not remove the oil pan…. , engine out or remove the k -member ( I need a hp pump , have low oil pressure when the engine is hot ) ..,, Greeting from Germany

@micheltremblay1667 Жыл бұрын

If the oil pick up is set to low,would that give you bad or low oil pressure?

@TheGarageGoblin Жыл бұрын

Unlikely, unless the oil pickup is sucking up dirt / sludge in the bottom of the oil pan and causing a clog. That clog could move into the oil galleys of your engine and could be potentially catastrophic. If you’re having low oil pressure definitely may end up needing to clean out the engine.

@micheltremblay1667 Жыл бұрын

Thank you

@jakewade7388 Жыл бұрын

Which camshaft are you going with?

@TheGarageGoblin Жыл бұрын

Edelbrock 2102 cam!

@maldo72 Жыл бұрын

🙄🙄🙄🙄🙄 you need to measure not just push the pan down over it and then push it down whatever feels good .... tack welding does not always work because you are welding cast iron to steel