Chevy 350 budget rebuild pt 9, oil pump, timing cover, and oil pan install

Рет қаралды 19,281

Cali530Marcos

2 жыл бұрын

Пікірлер: 51

@johngrepo9976 9 күн бұрын

I had the same problem, bought the install tool..😮 screen was installed in a minute!

@wreckanchor Жыл бұрын

Good video. One thing I use to double check I have at least 1/2 inch clearance between the oil pan and the pickup is to remove the drain plug and run a cheap bore scope camera in thru the drain hole so I can see the clearance. The scope cost like 30 bucks on Amazon and I use it for all sorts of stuff.

@cali530marcos3 Жыл бұрын

I need to buy me one, they come in handy

@labeledespjl 2 ай бұрын

Great video guy! About to do this tomorrow.

@cali530marcos3 2 ай бұрын

Thanks, and good luck

@heathergrupp6525 2 жыл бұрын

I like that this vato dont edit all the mistakes that la vida loca throws his way. We all have the world try to break us down. Its not perfect. But Holy Creator sees us through.

@cali530marcos3 2 жыл бұрын

thanks

@2010Flboy 9 ай бұрын

Nice tech tip regarding time gear dots.

@glennmanchester3666 Жыл бұрын

87 and up I believe is when the dipstick got moved to the passengers side and also the one piece rear ,main seal came into existence in lieu of the old two piece that always eventually leaks way worse and way sooner than the one piece one

@LifeAsItWeKnow Жыл бұрын

you have a excellent video here, plenty of light and I dont get dizzy from camera movement... very good.

@cali530marcos3 Жыл бұрын

Thanks, appreciate the support

@JAVIERHernandez-vt2nx 2 жыл бұрын

Good job bro

@cali530marcos3 2 жыл бұрын

Thanks

@elray2446 4 ай бұрын

She's looking good!

@cali530marcos3 4 ай бұрын

Thanks

@taxman3035 2 жыл бұрын

you gotta love the dog

@cali530marcos3 2 жыл бұрын

Yea, he's always next to me when I'm working in the back yard

@dennyr8492 Жыл бұрын

That's exactly what i say " REALLY" when i drop something that's not suppose to be dropped in .haha😂 or can't fine my wrench or socket i just put down a minute ago great video,

@cali530marcos3 Жыл бұрын

Seems to happen a lot to me, thanks on the support, I try to explain as much as I can without making the video too long

@dennyr8492 Жыл бұрын

So i got a question on your video on adjusting valve and pushrods. You put both dots away from each other facing up. For the Distributor to drop in. What so it will be sitting on number One cylinder on the compression side

@cali530marcos3 Жыл бұрын

@@dennyr8492 so first I do dot to dot so u can install the cam and timing chain and that gets all the valve train in sync, then u turn the dots away from each other so u can install the distributor and ur ready to fire it up, if u don’t u will be 180 degrees out and will just back fire when u go to start it

@dennyr8492 Жыл бұрын

@@cali530marcos3 so what cylinder will the rotor for the distributor be at ? I don't know if i do this wrong i set both dots together TDC then put the distributor rotor close to number one cylinder on the cap. Then if it's not firing right move the distributor till it fires.. sounds to me I'm off a little.i got Edelbrock aluminum heads and a Howard rattler cam in this 350 i don't want to ruin this motor

@cali530marcos3 Жыл бұрын

@@dennyr8492 on my cars I put the rotor between cylinder #1 and the thermostat housing

@earthbros6508 Жыл бұрын

Ahuevo! This video is helpful

@cali530marcos3 Жыл бұрын

Thanks, I tried to show most of it without making the video too long

@dgomes4464 2 жыл бұрын

With the dot on top you said the distributor is ready to go in, what position or cylinder? Do you have a video? Thank you.

@cali530marcos3 2 жыл бұрын

i do not have a video on that, but you point the rotor inside the distributer towards the #1 cylinder

@josecavada3830 7 ай бұрын

👍

@cali530marcos3 7 ай бұрын

Thanks

@jameswelch7516 2 жыл бұрын

Is this the end of the bild or are going to finish up with intake and carb extra

@cali530marcos3 2 жыл бұрын

i have one more vid on painting it, but thats it for now until i install it and do the first start up

@Supper_dad3 3 ай бұрын

I noticed your oil pump shaft didn’t engage to the pump and most vids I see they fit snug mine is like yours is that normal?

@cali530marcos3 3 ай бұрын

It depends if u have the plastic connector one or the metal shaft like mine, if it’s plastic it’s snugg and clips together, if it’s metal it just slides over it

@glennmanchester3666 Жыл бұрын

I just jumped in on this channel are you going to run a hei or a ,marine points distributor I've run both but of course prefer the hei

@cali530marcos3 Жыл бұрын

I’m using the marine distributor with an exterior coil

@jsolo7576 25 күн бұрын

What's so special about the marine points distributor?

@jsolo7576 25 күн бұрын

Ok. I just read a comment that says you're assembling a marine engine.

@TheMerm0311 Ай бұрын

What size are the 4 corner bolts for the oil pan?

@cali530marcos3 Ай бұрын

1/2 inch or 13mm

@glennmanchester3666 Жыл бұрын

Much better gasket kit anyway

@cali530marcos3 Жыл бұрын

Yea

@pennyraven1222 10 ай бұрын

I like you're pit bull. 4:33

@cali530marcos3 10 ай бұрын

Thanks, he’s 7 years old now and protects the hell out of my family

@lordsauto Жыл бұрын

did u check crankshaft end clearance. didnt see u do it

@cali530marcos3 Жыл бұрын

Yea, just did it off camera

@lordsauto Жыл бұрын

May I ask the process?

@fred1706 2 жыл бұрын

what grade of oil do you put

@cali530marcos3 2 жыл бұрын

I use 5w30 since everything in the engine is new

@JTsMechanicShop5748 2 жыл бұрын

Is that engine running yet

@cali530marcos3 2 жыл бұрын

Not yet, I just got done installing it in a 1987 Malibu ski boat, doing a video on installing all the accessories then imma do a first start up video

@glennmanchester3666 Жыл бұрын

Ski boat cool