Oh crap! You're right! I think I got confused with the length of the plexiglass. Good call! 8 hours of editing and I still made a little mistake, woops 😬

Thank you for watching! And I'm really glad this was helpful. Be sure to check the pinned comment because while editing I did made a small mistake. But just to make sire you won't actually make that mistake while making an enclosure

I'm glad you found it helpful 😁

No problem! I actually didn't use the tracks until after I made my first 3 enclosures lol The tracks work a lot better for sure.

@@jpslizards what did you use to secure the track to your wood??

Just silicone. Used clamps to hold them for 24 hours

@@jpslizards thank you!!

No problem 😊

That's what I did when I knew the extra room was going to be my reptile room haha good luck with the enclosures!

I use a lamp stand, this way I can move it however I want and also put the basking spot where ever I want. And no problem! ☺

No problem. I'm glad this is helpful 😃 Good luck

No problem bro. Just to make sure, what do you mean a cut list?

@@jpslizards I know I need to buy a 8'x4' 3/4" board. Could you just simply give me the dimensions needed to cut it down so I will have all the pieces to assemble it. Sorry for being so confusing lol.

I was the one that got confused bro, sorry. You were being literal lol I'm going to watch the video again because I was sure I added the measurements of the pieces. If not I will measure my set up to be exact and will get back to you later

@@joshuaburns7427 at 2:46 I show the measurements bro 😁

Thank you!

Thank you bro. This video was not easy to make at all. At first it didn't really get much views but it's doing a lot better now. I'm glad a few people have found this video helpful 😁

@@jpslizards how toes are always a great thing because people will always need youtube for DIY projects.

True! Once I make an enclosure that I have in mind I will record it as well

@@jpslizards Yes that will give you big views.

Nope, not at all. These set ups are big and have good ventilation.

That's really good. You're welcome

Thank you! 😁

Naw, since it's a big set up it has plenty of ventilation. It would probably only be bad if you want to add 2 basking areas

On future set up that I make for my lizards I won't be adding vents anymore

That's the way I was using them at first but the impact was making it easier to drill as well lol But thank you!

On the vent that is on the right side I cut one corner and ran the cords from there. In minute 6:36 you can see it. Sorry if I forgot to mention that!

That too! I just didn't want to do that because there was going to be another set up on top

Definitely, but it would have to go inside. Exact how? That I wouldn't really know because I don't use them. You would need to make sure the mat is below something that can let the heat go thru, like glass

I would cut what dried on the outside. Normally you want to clean what comes out after nailing it together

I used it along the inside four corner of the back the tops and sides, as my build had quite a few gaps along the inside where the boards met (uneven cuts) There is a generous amount of this liquid nails now, I accidentally used it in replace of the silicone, will any residue or chemicals soak into the bedding and cause issues with my Boas skin? (I’m not worried about it being peeled of or eaten)

Oh ok, I thought it was a lizard set up. As far as I know, no, it will be completely dry after a couple of days. I would still cut the extra stuff though. You can never be too careful. You can also waterproof the set up with drylock

Thank you 😄 Hope the video is helpful!

Oh that's nothing, you should hear me in the videos where I talk a lot more haha 😂

I know other have done it but I haven't. I wouldn't know what to suggest to be honest. I have only used drylok before

I think it's 19mm

Might as well go bigger in my opinion. Basically a small room lol that would be so awesome

@@jpslizards I want to build it to look like furniture. Her current enclosure is 24W×48Lx38H

Thank you! And to think that it was just to save a few bucks lol

Oh yeah, I have 2 stacked.

Yeah you missed the picture lol but no worries, I found it for you. I used tracks, which you can get from Amazon. In minute 2:23 you can see a picture of the one I got

Sorry, I'm just not sure what more info I could have given

I'm pretty sure 1/4 of an inch

It would be ok for both. More for leopard geckos but yes, it can also be used for a crested gecko, you would just have to waterproof it. This would be a mansion for either one of them lol

I'm pretty sure it was maple. They also had cedar and oak if I remember correctly

You can only use screws if you want. Silicone is just to make it hold a little better and to cover the edges

@@jpslizards thank you

Unless you plan to try to make it waterproof. Then it's a must

@@jpslizards no its for a thai bamboo rat snake so just high humidity low temp

If it needs high humidity then I suggest to water proof it. Unless you make the enclosure from pvc

Yeap, I need to by a better saw. Or get a table saw