... идея отличная получилась и работа проделана огромная!-, для пылесоса осталось сделать или колёсики, или рукоятку для переноски и транспортировки, молодец, здоровья тебе и удачи во всём новых творческих успехов!!!

While it would add to the cost, you can use a PVC pipe fitting for the suction connection. As it turns out, shop vac hoses fit PVC fittings pretty well

This is a really cool build. Would love to see you iterate on it and make a better filtration system for it. A cyclonic system would work well. These pleated filters always clog in shop vacs and reduces the suction a lot.

Now that is something very useful, thank you for this

Best make yet, well done R&R. 👌

The wet vacuum demonstration = the moisture/vapour generated by the water being sucked up will damage & eventually kill this particular vacuum motor as it is for filtered dry air only - due to how it is cooled, and as it has “no” indication of when it is full of water = the motor will flood and die if a large amount of water [over the capacity of the lower box] is being vacuumed.

Cute idea, but not "powerful" as you stated. Upgrade your motor and filter for the next one. Nice effort

Finally someone found a use for Cherry MX blue.

Nice to see a vacuum cleaner with DC Inverter technology

Great execution but the filter might be too small, i worry your motor will burn out for lack of flow....

I love this boxes and now i love You 😘

Genius. Love that idea.

At one point i saw the chisel pointed at your hand securing the lid. Never keep your fleshy bits in the path of the chisel. If it slips its going straight into your hand.

Clever I just wouldn’t glue the clasps down without fasteners - you can easily enough seal the leaks made by fasteners

Wow, very cool 👍✌️👌 thanks my friend 👋

Where did you get the motor from? Would like to see another one with a cyclonic filtration and more portable one.

Nice idea to make this one

Циклон из круглого ведра эфективнее так как завехрения не позволяют пыли подыматься к двигателю!

In my opinion, i recommend dust bag near filter. It keeps filter clean and dust bag when is it full just throw it away and add new 🥰

What kind of vacuum motor was that that kind of looks like a motor that you would find to blow up a blow up mattress for camping. Is that what it was?

Ottima idea mi può indicare link del motore grazie

excellente réalisation , mais il manque une chicane entre l'entrée de l'air et ses saletés et son trajet vers le filtre, avec une chicane le filtre se bouche moins vite

Good project I need circuit diagram for how to wire the motor . I think i have 3 phase bldc motor .can you hlep me

Nice build! I like the modularity (assuming that you use Turnover Boxes extensively in your organizational system.) 2 suggestions if your are open to them. 1st when you put the latches on, I like that you install them before apply the sealing strip so that it will seal with the preser from the foam. If you put the latches on the top box or the "body of the vacuum" just like you did with the foam sealing strip then any turnover box of the appropriate size could be used as all necessary parts are on one piece. 2nd I agree with Samuel Fellows the motor electronics are quite vulnerable in this build perhaps an enclosed motor or shaft driven turbine and have the motor out of the air stream. Love the idea.

I reckon that pipe is to wide for a small motor like that but still awsome though good job 👍

Dope build man!

I guess sucking up the water would clean out the hose lol, good job,but I don't have a 3D printer as yet!!

Fun project with a compact result

You should make a vortex version of this .

Cool idea 👍 you happy with the results ?

La batería acostada..???? Todas van de pie...es más fácil sacarlas...

Same like the milwaukee packout vacuüm cleaner

Two motors. No wait; three.

用什么品牌的海帕？ 我之前也想做垃圾佬自己搞一个

I will buy that :)

No keycap on the switch... NOOO

Chique show 👍👍🎸!!!!

Идея интересная, но есть у меня сильное подозрение, что в такой конструкции двигатель проработает не долго. Перед ним нужен ещё один фильтр, или хотябы мелкая сеточка.

where did you get the motor from?

Super nápad👍

От чего мотор?

motor tanpa berus karbon, bumyi pun tak bising sangat

Potente.????

Part list?

need a filterbag~!!

I bought a vacuum cleaner for 32 eur instead

That hand and chisel don't look pretty

Второго фильтра не хватает. В виде мешка накидного. Из плотного полимерного полотна, типа синтипона.

why not just buy a vacuum?

维新

Step 1: Buy a 3d printer and form specialty parts

Or buy one

Cool build but it is NOT powerful.

Or you can just buy a vacuum.

It's... Not really a great design though. Sorry.

Too weak